Currently UFS HCI uses UFS_BIT() macro to get various bit position for the hardware registers status bits. Which makes code longer instead of shorter. This macro does not improve code readability as well. Lets re-write these macro definition with the actual bit position. Suggested-by: Bart Van Assche <Bart.VanAssche@xxxxxxx> Signed-off-by: Alim Akhtar <alim.akhtar@xxxxxxxxxxx> --- This patch is only complied tested, appreciate testing on actual h/w. Please see https://lkml.org/lkml/2017/8/28/786 discussion. drivers/scsi/ufs/ufshcd.h | 14 +++++----- drivers/scsi/ufs/ufshci.h | 69 ++++++++++++++++++++++++----------------------- 2 files changed, 43 insertions(+), 40 deletions(-) diff --git a/drivers/scsi/ufs/ufshcd.h b/drivers/scsi/ufs/ufshcd.h index cdc8bd0..ce2920b 100644 --- a/drivers/scsi/ufs/ufshcd.h +++ b/drivers/scsi/ufs/ufshcd.h @@ -544,13 +544,13 @@ struct ufs_hba { bool is_irq_enabled; /* Interrupt aggregation support is broken */ - #define UFSHCD_QUIRK_BROKEN_INTR_AGGR UFS_BIT(0) + #define UFSHCD_QUIRK_BROKEN_INTR_AGGR 0x1 /* * delay before each dme command is required as the unipro * layer has shown instabilities */ - #define UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS UFS_BIT(1) + #define UFSHCD_QUIRK_DELAY_BEFORE_DME_CMDS 0x2 /* * If UFS host controller is having issue in processing LCC (Line @@ -559,21 +559,21 @@ struct ufs_hba { * the LCC transmission on UFS device (by clearing TX_LCC_ENABLE * attribute of device to 0). */ - #define UFSHCD_QUIRK_BROKEN_LCC UFS_BIT(2) + #define UFSHCD_QUIRK_BROKEN_LCC 0x4 /* * The attribute PA_RXHSUNTERMCAP specifies whether or not the * inbound Link supports unterminated line in HS mode. Setting this * attribute to 1 fixes moving to HS gear. */ - #define UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP UFS_BIT(3) + #define UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP 0x8 /* * This quirk needs to be enabled if the host contoller only allows * accessing the peer dme attributes in AUTO mode (FAST AUTO or * SLOW AUTO). */ - #define UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE UFS_BIT(4) + #define UFSHCD_QUIRK_DME_PEER_ACCESS_AUTO_MODE 0x10 /* * This quirk needs to be enabled if the host contoller doesn't @@ -581,13 +581,13 @@ struct ufs_hba { * is enabled, standard UFS host driver will call the vendor specific * ops (get_ufs_hci_version) to get the correct version. */ - #define UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION UFS_BIT(5) + #define UFSHCD_QUIRK_BROKEN_UFS_HCI_VERSION 0x20 /* * This quirk needs to be enabled if the host contoller regards * resolution of the values of PRDTO and PRDTL in UTRD as byte. */ - #define UFSHCD_QUIRK_PRDT_BYTE_GRAN UFS_BIT(7) + #define UFSHCD_QUIRK_PRDT_BYTE_GRAN 0x80 unsigned int quirks; /* Deviations from standard UFSHCI spec. */ diff --git a/drivers/scsi/ufs/ufshci.h b/drivers/scsi/ufs/ufshci.h index f60145d..5a60a8f 100644 --- a/drivers/scsi/ufs/ufshci.h +++ b/drivers/scsi/ufs/ufshci.h @@ -119,22 +119,24 @@ enum { #define MANUFACTURE_ID_MASK UFS_MASK(0xFFFF, 0) #define PRODUCT_ID_MASK UFS_MASK(0xFFFF, 16) -#define UFS_BIT(x) (1L << (x)) - -#define UTP_TRANSFER_REQ_COMPL UFS_BIT(0) -#define UIC_DME_END_PT_RESET UFS_BIT(1) -#define UIC_ERROR UFS_BIT(2) -#define UIC_TEST_MODE UFS_BIT(3) -#define UIC_POWER_MODE UFS_BIT(4) -#define UIC_HIBERNATE_EXIT UFS_BIT(5) -#define UIC_HIBERNATE_ENTER UFS_BIT(6) -#define UIC_LINK_LOST UFS_BIT(7) -#define UIC_LINK_STARTUP UFS_BIT(8) -#define UTP_TASK_REQ_COMPL UFS_BIT(9) -#define UIC_COMMAND_COMPL UFS_BIT(10) -#define DEVICE_FATAL_ERROR UFS_BIT(11) -#define CONTROLLER_FATAL_ERROR UFS_BIT(16) -#define SYSTEM_BUS_FATAL_ERROR UFS_BIT(17) +#define UFS_BIT(x) (1L << (x)) +/* + * IS - Interrupt Status - 20h + */ +#define UTP_TRANSFER_REQ_COMPL 0x1 +#define UIC_DME_END_PT_RESET 0x2 +#define UIC_ERROR 0x4 +#define UIC_TEST_MODE 0x8 +#define UIC_POWER_MODE 0x10 +#define UIC_HIBERNATE_EXIT 0x20 +#define UIC_HIBERNATE_ENTER 0x40 +#define UIC_LINK_LOST 0x80 +#define UIC_LINK_STARTUP 0x100 +#define UTP_TASK_REQ_COMPL 0x200 +#define UIC_COMMAND_COMPL 0x400 +#define DEVICE_FATAL_ERROR 0x800 +#define CONTROLLER_FATAL_ERROR 0x10000 +#define SYSTEM_BUS_FATAL_ERROR 0x20000 #define UFSHCD_UIC_PWR_MASK (UIC_HIBERNATE_ENTER |\ UIC_HIBERNATE_EXIT |\ @@ -152,10 +154,10 @@ enum { SYSTEM_BUS_FATAL_ERROR) /* HCS - Host Controller Status 30h */ -#define DEVICE_PRESENT UFS_BIT(0) -#define UTP_TRANSFER_REQ_LIST_READY UFS_BIT(1) -#define UTP_TASK_REQ_LIST_READY UFS_BIT(2) -#define UIC_COMMAND_READY UFS_BIT(3) +#define DEVICE_PRESENT 0x1 +#define UTP_TRANSFER_REQ_LIST_READY 0x2 +#define UTP_TASK_REQ_LIST_READY 0x4 +#define UIC_COMMAND_READY 0x8 #define HOST_ERROR_INDICATOR UFS_BIT(4) #define DEVICE_ERROR_INDICATOR UFS_BIT(5) #define UIC_POWER_MODE_CHANGE_REQ_STATUS_MASK UFS_MASK(0x7, 8) @@ -174,46 +176,47 @@ enum { }; /* HCE - Host Controller Enable 34h */ -#define CONTROLLER_ENABLE UFS_BIT(0) +#define CONTROLLER_ENABLE 0x1 #define CONTROLLER_DISABLE 0x0 -#define CRYPTO_GENERAL_ENABLE UFS_BIT(1) +#define CRYPTO_GENERAL_ENABLE 0x2 /* UECPA - Host UIC Error Code PHY Adapter Layer 38h */ -#define UIC_PHY_ADAPTER_LAYER_ERROR UFS_BIT(31) +#define UIC_PHY_ADAPTER_LAYER_ERROR 0x80000000 #define UIC_PHY_ADAPTER_LAYER_ERROR_CODE_MASK 0x1F #define UIC_PHY_ADAPTER_LAYER_LANE_ERR_MASK 0xF /* UECDL - Host UIC Error Code Data Link Layer 3Ch */ -#define UIC_DATA_LINK_LAYER_ERROR UFS_BIT(31) +#define UIC_DATA_LINK_LAYER_ERROR 0x80000000 #define UIC_DATA_LINK_LAYER_ERROR_CODE_MASK 0x7FFF #define UIC_DATA_LINK_LAYER_ERROR_PA_INIT 0x2000 #define UIC_DATA_LINK_LAYER_ERROR_NAC_RECEIVED 0x0001 #define UIC_DATA_LINK_LAYER_ERROR_TCx_REPLAY_TIMEOUT 0x0002 /* UECN - Host UIC Error Code Network Layer 40h */ -#define UIC_NETWORK_LAYER_ERROR UFS_BIT(31) +#define UIC_NETWORK_LAYER_ERROR 0x80000000 #define UIC_NETWORK_LAYER_ERROR_CODE_MASK 0x7 /* UECT - Host UIC Error Code Transport Layer 44h */ -#define UIC_TRANSPORT_LAYER_ERROR UFS_BIT(31) +#define UIC_TRANSPORT_LAYER_ERROR 0x80000000 #define UIC_TRANSPORT_LAYER_ERROR_CODE_MASK 0x7F /* UECDME - Host UIC Error Code DME 48h */ -#define UIC_DME_ERROR UFS_BIT(31) +#define UIC_DME_ERROR 0x80000000 #define UIC_DME_ERROR_CODE_MASK 0x1 +/* UTRIACR - Interrupt Aggregation control register - 0x4Ch */ #define INT_AGGR_TIMEOUT_VAL_MASK 0xFF #define INT_AGGR_COUNTER_THRESHOLD_MASK UFS_MASK(0x1F, 8) -#define INT_AGGR_COUNTER_AND_TIMER_RESET UFS_BIT(16) -#define INT_AGGR_STATUS_BIT UFS_BIT(20) -#define INT_AGGR_PARAM_WRITE UFS_BIT(24) -#define INT_AGGR_ENABLE UFS_BIT(31) +#define INT_AGGR_COUNTER_AND_TIMER_RESET 0x10000 +#define INT_AGGR_STATUS_BIT 0x100000 +#define INT_AGGR_PARAM_WRITE 0x1000000 +#define INT_AGGR_ENABLE 0x80000000 /* UTRLRSR - UTP Transfer Request Run-Stop Register 60h */ -#define UTP_TRANSFER_REQ_LIST_RUN_STOP_BIT UFS_BIT(0) +#define UTP_TRANSFER_REQ_LIST_RUN_STOP_BIT 0x1 /* UTMRLRSR - UTP Task Management Request Run-Stop Register 80h */ -#define UTP_TASK_REQ_LIST_RUN_STOP_BIT UFS_BIT(0) +#define UTP_TASK_REQ_LIST_RUN_STOP_BIT 0x1 /* UICCMD - UIC Command */ #define COMMAND_OPCODE_MASK 0xFF -- 2.7.4
