Hi Sunyeal,
On 7/5/24 11:11, Sunyeal Hong wrote:
> Add cmu_top, cmu_peric0 clock nodes and
> switch USI clocks instead of dummy fixed-rate-clock.
>
> Signed-off-by: Sunyeal Hong <sunyeal.hong@xxxxxxxxxxx>
> ---
> .../arm64/boot/dts/exynos/exynosautov920.dtsi | 40 +++++++++++++------
> 1 file changed, 27 insertions(+), 13 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> index c1c8566d74f5..1659c0a375c9 100644
> --- a/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> +++ b/arch/arm64/boot/dts/exynos/exynosautov920.dtsi
> @@ -6,6 +6,7 @@
> *
> */
>
> +#include <dt-bindings/clock/samsung,exynosautov920.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> #include <dt-bindings/soc/samsung,exynos-usi.h>
>
> @@ -38,17 +39,6 @@ xtcxo: clock {
> clock-output-names = "oscclk";
> };
>
> - /*
> - * FIXME: Keep the stub clock for serial driver, until proper clock
> - * driver is implemented.
> - */
> - clock_usi: clock-usi {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <200000000>;
> - clock-output-names = "usi";
> - };
> -
> cpus: cpus {
> #address-cells = <2>;
> #size-cells = <0>;
> @@ -182,6 +172,28 @@ chipid@10000000 {
> reg = <0x10000000 0x24>;
> };
>
> + cmu_peric0: clock-controller@10800000 {
> + compatible = "samsung,exynosautov920-cmu-peric0";
> + reg = <0x10800000 0x8000>;
> + #clock-cells = <1>;
> +
> + clocks = <&xtcxo>,
> + <&cmu_top DOUT_CLKCMU_PERIC0_NOC>,
> + <&cmu_top DOUT_CLKCMU_PERIC0_IP>;
> + clock-names = "oscclk",
> + "dout_clkcmu_peric0_noc",
> + "dout_clkcmu_peric0_ip";
> + };
> +
> + cmu_top: clock-controller@11000000 {
> + compatible = "samsung,exynosautov920-cmu-top";
> + reg = <0x11000000 0x8000>;
> + #clock-cells = <1>;
> +
> + clocks = <&xtcxo>;
> + clock-names = "oscclk";
> + };
> +
> gic: interrupt-controller@10400000 {
> compatible = "arm,gic-v3";
> #interrupt-cells = <3>;
> @@ -213,7 +225,8 @@ usi_0: usi@108800c0 {
> #address-cells = <1>;
> #size-cells = <1>;
> ranges;
> - clocks = <&clock_usi>, <&clock_usi>;
> + clocks = <&cmu_peric0 CLK_DOUT_PERIC0_USI00_USI>,
> + <&cmu_peric0 CLK_MOUT_PERIC0_NOC_USER>;
it seems that the clocks have been switched.
CLK_DOUT_PERIC0_USI00_USI is ipclk and CLK_MOUT_PERIC0_NOC_USER is pclk of USI.
> clock-names = "pclk", "ipclk";
> status = "disabled";
>
> @@ -224,7 +237,8 @@ serial_0: serial@10880000 {
> interrupts = <GIC_SPI 764 IRQ_TYPE_LEVEL_HIGH>;
> pinctrl-names = "default";
> pinctrl-0 = <&uart0_bus>;
> - clocks = <&clock_usi>, <&clock_usi>;
> + clocks = <&cmu_peric0 CLK_MOUT_PERIC0_NOC_USER>,
> + <&cmu_peric0 CLK_DOUT_PERIC0_USI00_USI>;
> clock-names = "uart", "clk_uart_baud0";
> samsung,uart-fifosize = <256>;
> status = "disabled";
Thanks
Jaewon Kim
