Add support for the Exynos USB 3.1 DRD combo phy, as found in Exynos 9
SoCs like Google GS101. It supports USB SS, HS and DisplayPort.
In terms of UTMI+, this is very similar to the existing Exynos850
support in this driver. The difference is that it supports both UTMI+
(HS) and PIPE3 (SS).
The number of ports for each can be determined using the LINKPORT
register (which also exists on Exynos E850).
For SuperSpeed (SS), the PIPE3 interface is new compared to Exynos
E850, and also very different from the existing support for older
Exynos SoCs in this driver.
It needs a bit more configuration work and register tuning for signal
quality to work reliably, presumably due to the higher frequency, e.g.
to account for different board layouts.
This commit adds the necessary changes for USB HS and SS to work.
DisplayPort is out of scope in this commit.
Notes:
* For the register tuning, exynos5_usbdrd_apply_phy_tunes() has been
added with the appropriate data structures to support tuning at
various stages during initialisation. Since these are hardware
specific, the platform data is supposed to be populated accordingly.
The implementation is loosely modelled after the Samsung UFS PHY
driver.
There is one tuning state for UTMI+, PTS_UTMI_POSTINIT, to execute
after init and generally intended for HS signal tuning, as done in
this commit.
PTS_PIPE3_PREINIT PTS_PIPE3_INIT PTS_PIPE3_POSTINIT
PTS_PIPE3_POSTLOCK are tuning states for PIPE3. In the downstream
driver, preinit differs by Exynos SoC, and postinit and postlock
are different per board. The latter haven't been implemented for
gs101 here, because downstream doesn't use them on gs101 either.
* Signal lock acquisition for SS depends on the orientation of the
USB-C plug. Since there currently is no infrastructure to chain
connector events to both the USB DWC3 driver and this phy driver, a
work-around has been added in
exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock() to check both
registers if it failed in one of the orientations.
* Equally, we can only establish SS speed in one of the connector
orientations due to programming differences when selecting the lane
mux in exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(), which really
needs to be dynamic, based on the orientation of the connector.
* As is, we can establish a HS link using any cable, and an SS link in
one orientation of the plug, falling back to HS if the orientation is
reversed to the expectation.
Signed-off-by: André Draszik <andre.draszik@xxxxxxxxxx>
---
drivers/phy/samsung/phy-exynos5-usbdrd.c | 610 +++++++++++++++++++++++++++-
include/linux/soc/samsung/exynos-regs-pmu.h | 4 +
2 files changed, 608 insertions(+), 6 deletions(-)
diff --git a/drivers/phy/samsung/phy-exynos5-usbdrd.c b/drivers/phy/samsung/phy-exynos5-usbdrd.c
index 63933029ffa7..48a5b84feaea 100644
--- a/drivers/phy/samsung/phy-exynos5-usbdrd.c
+++ b/drivers/phy/samsung/phy-exynos5-usbdrd.c
@@ -133,11 +133,27 @@
/* Exynos850: USB DRD PHY registers */
#define EXYNOS850_DRD_LINKCTRL 0x04
+#define LINKCTRL_FORCE_RXELECIDLE BIT(18)
+#define LINKCTRL_FORCE_PHYSTATUS BIT(17)
+#define LINKCTRL_FORCE_PIPE_EN BIT(16)
#define LINKCTRL_FORCE_QACT BIT(8)
#define LINKCTRL_BUS_FILTER_BYPASS(_x) ((_x) << 4)
+#define EXYNOS850_DRD_LINKPORT 0x08
+#define LINKPORT_HOST_NUM_U3 GENMASK(19, 16)
+#define LINKPORT_HOST_NUM_U2 GENMASK(15, 12)
+
#define EXYNOS850_DRD_CLKRST 0x20
+/*
+ * On versions without SS ports (like E850), bit 3 is for the 2.0 phy (HS),
+ * while on versions with (like gs101), bits 2 and 3 are for the 3.0 phy (SS)
+ * and bits 12 & 13 for the 2.0 phy.
+ */
+#define CLKRST_PHY20_SW_POR BIT(13)
+#define CLKRST_PHY20_SW_POR_SEL BIT(12)
+#define CLKRST_LINK_PCLK_SEL BIT(7)
#define CLKRST_PHY_SW_RST BIT(3)
+#define CLKRST_PHY_RESET_SEL BIT(2)
#define CLKRST_PORT_RST BIT(1)
#define CLKRST_LINK_SW_RST BIT(0)
@@ -159,12 +175,173 @@
#define HSP_EN_UTMISUSPEND BIT(9)
#define HSP_COMMONONN BIT(8)
+#define EXYNOS850_DRD_HSPPARACON 0x58
+#define HSPPARACON_TXVREF GENMASK(31, 28)
+#define HSPPARACON_TXRISE GENMASK(25, 24)
+#define HSPPARACON_TXRES GENMASK(22, 21)
+#define HSPPARACON_TXPREEMPPULSE BIT(20)
+#define HSPPARACON_TXPREEMPAMP GENMASK(19, 18)
+#define HSPPARACON_TXHSXV GENMASK(17, 16)
+#define HSPPARACON_TXFSLS GENMASK(15, 12)
+#define HSPPARACON_SQRX GENMASK(10, 8)
+#define HSPPARACON_OTG GENMASK(6, 4)
+#define HSPPARACON_COMPDIS GENMASK(2, 0)
+
#define EXYNOS850_DRD_HSP_TEST 0x5c
#define HSP_TEST_SIDDQ BIT(24)
+/* Exynos9 - GS101 */
+#define EXYNOS850_DRD_SECPMACTL 0x48
+#define SECPMACTL_PMA_ROPLL_REF_CLK_SEL GENMASK(13, 12)
+#define SECPMACTL_PMA_LCPLL_REF_CLK_SEL GENMASK(11, 10)
+#define SECPMACTL_PMA_REF_FREQ_SEL GENMASK(9, 8)
+#define SECPMACTL_PMA_LOW_PWR BIT(4)
+#define SECPMACTL_PMA_TRSV_SW_RST BIT(3)
+#define SECPMACTL_PMA_CMN_SW_RST BIT(2)
+#define SECPMACTL_PMA_INIT_SW_RST BIT(1)
+#define SECPMACTL_PMA_APB_SW_RST BIT(0)
+
+/* PMA registers */
+#define EXYNOS9_PMA_USBDP_CMN_REG0008 0x0020
+#define CMN_REG0008_OVRD_AUX_EN BIT(3)
+#define CMN_REG0008_AUX_EN BIT(2)
+
+#define EXYNOS9_PMA_USBDP_CMN_REG00B8 0x02e0
+#define CMN_REG00B8_LANE_MUX_SEL_DP GENMASK(3, 0)
+
+#define EXYNOS9_PMA_USBDP_CMN_REG01C0 0x0700
+#define CMN_REG01C0_ANA_LCPLL_LOCK_DONE BIT(7)
+#define CMN_REG01C0_ANA_LCPLL_AFC_DONE BIT(6)
+
+/* these have similar register layout, for lanes 0 and 2 */
+#define EXYNOS9_PMA_USBDP_TRSV_REG03C3 0x0f0c
+#define EXYNOS9_PMA_USBDP_TRSV_REG07C3 0x1f0c
+#define TRSV_REG03C3_LN0_MON_RX_CDR_AFC_DONE BIT(3)
+#define TRSV_REG03C3_LN0_MON_RX_CDR_CAL_DONE BIT(2)
+#define TRSV_REG03C3_LN0_MON_RX_CDR_FLD_PLL_MODE_DONE BIT(1)
+#define TRSV_REG03C3_LN0_MON_RX_CDR_LOCK_DONE BIT(0)
+
+/* TRSV_REG0413 and TRSV_REG0813 have similar register layout */
+#define EXYNOS9_PMA_USBDP_TRSV_REG0413 0x104c
+#define TRSV_REG0413_OVRD_LN1_TX_RXD_COMP_EN BIT(7)
+#define TRSV_REG0413_OVRD_LN1_TX_RXD_EN BIT(5)
+
+#define EXYNOS9_PMA_USBDP_TRSV_REG0813 0x204c
+#define TRSV_REG0813_OVRD_LN3_TX_RXD_COMP_EN BIT(7)
+#define TRSV_REG0813_OVRD_LN3_TX_RXD_EN BIT(5)
+
+/* PCS registers */
+#define EXYNOS9_PCS_NS_VEC_PS1_N1 0x010c
+#define EXYNOS9_PCS_NS_VEC_PS2_N0 0x0110
+#define EXYNOS9_PCS_NS_VEC_PS3_N0 0x0118
+#define NS_VEC_NS_REQ GENMASK(31, 24)
+#define NS_VEC_ENABLE_TIMER BIT(22)
+#define NS_VEC_SEL_TIMEOUT GENMASK(21, 20)
+#define NS_VEC_INV_MASK GENMASK(19, 16)
+#define NS_VEC_COND_MASK GENMASK(11, 8)
+#define NS_VEC_EXP_COND GENMASK(3, 0)
+
+#define EXYNOS9_PCS_OUT_VEC_2 0x014c
+#define EXYNOS9_PCS_OUT_VEC_3 0x0150
+#define PCS_OUT_VEC_B9_DYNAMIC BIT(19)
+#define PCS_OUT_VEC_B9_SEL_OUT BIT(18)
+#define PCS_OUT_VEC_B8_DYNAMIC BIT(17)
+#define PCS_OUT_VEC_B8_SEL_OUT BIT(16)
+#define PCS_OUT_VEC_B7_DYNAMIC BIT(15)
+#define PCS_OUT_VEC_B7_SEL_OUT BIT(14)
+#define PCS_OUT_VEC_B6_DYNAMIC BIT(13)
+#define PCS_OUT_VEC_B6_SEL_OUT BIT(12)
+#define PCS_OUT_VEC_B5_DYNAMIC BIT(11)
+#define PCS_OUT_VEC_B5_SEL_OUT BIT(10)
+#define PCS_OUT_VEC_B4_DYNAMIC BIT(9)
+#define PCS_OUT_VEC_B4_SEL_OUT BIT(8)
+#define PCS_OUT_VEC_B3_DYNAMIC BIT(7)
+#define PCS_OUT_VEC_B3_SEL_OUT BIT(6)
+#define PCS_OUT_VEC_B2_DYNAMIC BIT(5)
+#define PCS_OUT_VEC_B2_SEL_OUT BIT(4)
+#define PCS_OUT_VEC_B1_DYNAMIC BIT(3)
+#define PCS_OUT_VEC_B1_SEL_OUT BIT(2)
+#define PCS_OUT_VEC_B0_DYNAMIC BIT(1)
+#define PCS_OUT_VEC_B0_SEL_OUT BIT(0)
+
+#define EXYNOS9_PCS_TIMEOUT_0 0x0170
+
+#define EXYNOS9_PCS_TIMEOUT_3 0x017c
+
+#define EXYNOS9_PCS_EBUF_PARAM 0x0304
+#define EBUF_PARAM_SKP_REMOVE_TH_EMPTY_MODE GENMASK(29, 24)
+
+#define EXYNOS9_PCS_BACK_END_MODE_VEC 0x030c
+#define BACK_END_MODE_VEC_FORCE_EBUF_EMPTY_MODE BIT(1)
+#define BACK_END_MODE_VEC_DISABLE_DATA_MASK BIT(0)
+
+#define EXYNOS9_PCS_RX_CONTROL 0x03f0
+#define RX_CONTROL_EN_BLOCK_ALIGNER_TYPE_B BIT(22)
+
+#define EXYNOS9_PCS_RX_CONTROL_DEBUG 0x03f4
+#define RX_CONTROL_DEBUG_EN_TS_CHECK BIT(5)
+#define RX_CONTROL_DEBUG_NUM_COM_FOUND GENMASK(3, 0)
+
+#define EXYNOS9_PCS_LOCAL_COEF 0x040c
+#define LOCAL_COEF_PMA_CENTER_COEF GENMASK(21, 16)
+#define LOCAL_COEF_LF GENMASK(13, 8)
+#define LOCAL_COEF_FS GENMASK(5, 0)
+
+#define EXYNOS9_PCS_HS_TX_COEF_MAP_0 0x0410
+#define HS_TX_COEF_MAP_0_SSTX_DEEMP GENMASK(17, 12)
+#define HS_TX_COEF_MAP_0_SSTX_LEVEL GENMASK(11, 6)
+#define HS_TX_COEF_MAP_0_SSTX_PRE_SHOOT GENMASK(5, 0)
+
+
#define KHZ 1000
#define MHZ (KHZ * KHZ)
+#define PHY_TUNING_ENTRY_PHY(o, m, v) { \
+ .off = (o), \
+ .mask = (m), \
+ .val = (v), \
+ .region = PTR_PHY \
+ }
+
+#define PHY_TUNING_ENTRY_PCS(o, m, v) { \
+ .off = (o), \
+ .mask = (m), \
+ .val = (v), \
+ .region = PTR_PCS \
+ }
+
+#define PHY_TUNING_ENTRY_PMA(o, m, v) { \
+ .off = (o), \
+ .mask = (m), \
+ .val = (v), \
+ .region = PTR_PMA, \
+ }
+
+#define PHY_TUNING_ENTRY_LAST { .region = PTR_INVALID }
+
+#define for_each_phy_tune(tune) \
+ for (; (tune)->region != PTR_INVALID; ++(tune))
+
+struct exynos5_usbdrd_phy_tuning {
+ u32 off;
+ u32 mask;
+ u32 val;
+ char region;
+#define PTR_INVALID 0
+#define PTR_PHY 1
+#define PTR_PCS 2
+#define PTR_PMA 3
+};
+
+enum exynos5_usbdrd_phy_tuning_state {
+ PTS_UTMI_POSTINIT,
+ PTS_PIPE3_PREINIT,
+ PTS_PIPE3_INIT,
+ PTS_PIPE3_POSTINIT,
+ PTS_PIPE3_POSTLOCK,
+ PTS_MAX,
+};
+
enum exynos5_usbdrd_phy_id {
EXYNOS5_DRDPHY_UTMI,
EXYNOS5_DRDPHY_PIPE3,
@@ -183,6 +360,7 @@ struct exynos5_usbdrd_phy_config {
struct exynos5_usbdrd_phy_drvdata {
const struct exynos5_usbdrd_phy_config *phy_cfg;
+ const struct exynos5_usbdrd_phy_tuning **phy_tunes;
const struct phy_ops *phy_ops;
u32 pmu_offset_usbdrd0_phy;
u32 pmu_offset_usbdrd0_phy_ss;
@@ -194,6 +372,8 @@ struct exynos5_usbdrd_phy_drvdata {
* struct exynos5_usbdrd_phy - driver data for USB 3.0 PHY
* @dev: pointer to device instance of this platform device
* @reg_phy: usb phy controller register memory base
+ * @reg_pcs: usb phy physical coding sublayer register memory base
+ * @reg_pma: usb phy physical media attachment register memory base
* @phy_clks: phy clocks for register access
* @n_phy_clks: number of phy clocks for register access
* @pipeclk: clock for pipe3 phy
@@ -212,6 +392,8 @@ struct exynos5_usbdrd_phy_drvdata {
struct exynos5_usbdrd_phy {
struct device *dev;
void __iomem *reg_phy;
+ void __iomem *reg_pcs;
+ void __iomem *reg_pma;
struct clk_bulk_data *phy_clks;
size_t n_phy_clks;
struct clk *pipeclk;
@@ -363,6 +545,45 @@ exynos5_usbdrd_utmi_set_refclk(struct phy_usb_instance *inst)
return reg;
}
+static void
+exynos5_usbdrd_apply_phy_tunes(struct exynos5_usbdrd_phy *phy_drd,
+ enum exynos5_usbdrd_phy_tuning_state state)
+{
+ const struct exynos5_usbdrd_phy_tuning *tune;
+
+ tune = phy_drd->drv_data->phy_tunes[state];
+ if (!tune)
+ return;
+
+ for_each_phy_tune(tune) {
+ void __iomem *reg_base;
+ u32 reg = 0;
+
+ switch (tune->region) {
+ case PTR_PHY:
+ reg_base = phy_drd->reg_phy;
+ break;
+ case PTR_PCS:
+ reg_base = phy_drd->reg_pcs;
+ break;
+ case PTR_PMA:
+ reg_base = phy_drd->reg_pma;
+ break;
+ default:
+ dev_warn_once(phy_drd->dev,
+ "unknown phy region %d\n", tune->region);
+ continue;
+ }
+
+ if (~tune->mask) {
+ reg = readl(reg_base + tune->off);
+ reg &= ~tune->mask;
+ }
+ reg |= tune->val;
+ writel(reg, reg_base + tune->off);
+ }
+}
+
static void exynos5_usbdrd_pipe3_init(struct exynos5_usbdrd_phy *phy_drd)
{
u32 reg;
@@ -378,6 +599,159 @@ static void exynos5_usbdrd_pipe3_init(struct exynos5_usbdrd_phy *phy_drd)
writel(reg, phy_drd->reg_phy + EXYNOS5_DRD_PHYTEST);
}
+static void
+exynos5_usbdrd_usbdp_g2_v4_ctrl_pma_ready(struct exynos5_usbdrd_phy *phy_drd)
+{
+ void __iomem *regs_base = phy_drd->reg_phy;
+ u32 reg;
+
+ /* link pipe_clock selection to pclk of PMA */
+ reg = readl(regs_base + EXYNOS850_DRD_CLKRST);
+ reg |= CLKRST_LINK_PCLK_SEL;
+ writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
+
+ reg = readl(regs_base + EXYNOS850_DRD_SECPMACTL);
+ reg &= ~SECPMACTL_PMA_REF_FREQ_SEL;
+ reg |= FIELD_PREP_CONST(SECPMACTL_PMA_REF_FREQ_SEL, 1);
+ /* SFR reset */
+ reg |= (SECPMACTL_PMA_LOW_PWR | SECPMACTL_PMA_APB_SW_RST);
+ reg &= ~(SECPMACTL_PMA_ROPLL_REF_CLK_SEL |
+ SECPMACTL_PMA_LCPLL_REF_CLK_SEL);
+ /* PMA power off */
+ reg |= (SECPMACTL_PMA_TRSV_SW_RST | SECPMACTL_PMA_CMN_SW_RST |
+ SECPMACTL_PMA_INIT_SW_RST);
+ writel(reg, regs_base + EXYNOS850_DRD_SECPMACTL);
+
+ udelay(1);
+
+ reg = readl(regs_base + EXYNOS850_DRD_SECPMACTL);
+ reg &= ~SECPMACTL_PMA_LOW_PWR;
+ writel(reg, regs_base + EXYNOS850_DRD_SECPMACTL);
+
+ udelay(1);
+
+ /* release override */
+ reg = readl(regs_base + EXYNOS850_DRD_LINKCTRL);
+ reg &= ~LINKCTRL_FORCE_PIPE_EN;
+ writel(reg, regs_base + EXYNOS850_DRD_LINKCTRL);
+
+ udelay(1);
+
+ /* APB enable */
+ reg = readl(regs_base + EXYNOS850_DRD_SECPMACTL);
+ reg &= ~SECPMACTL_PMA_APB_SW_RST;
+ writel(reg, regs_base + EXYNOS850_DRD_SECPMACTL);
+}
+
+static void
+exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(struct exynos5_usbdrd_phy *phy_drd)
+{
+ void __iomem *regs_base = phy_drd->reg_pma;
+ u32 reg;
+
+ /* lane configuration: USB on all lanes */
+ reg = readl(regs_base + EXYNOS9_PMA_USBDP_CMN_REG00B8);
+ reg &= ~CMN_REG00B8_LANE_MUX_SEL_DP;
+ writel(reg, regs_base + EXYNOS9_PMA_USBDP_CMN_REG00B8);
+
+ /*
+ * FIXME: below code supports one connector orientation only. It needs
+ * updating once we can receive connector events.
+ */
+ /* override of TX receiver detector and comparator: lane 1 */
+ reg = readl(regs_base + EXYNOS9_PMA_USBDP_TRSV_REG0413);
+ reg &= ~TRSV_REG0413_OVRD_LN1_TX_RXD_COMP_EN;
+ reg &= ~TRSV_REG0413_OVRD_LN1_TX_RXD_EN;
+ writel(reg, regs_base + EXYNOS9_PMA_USBDP_TRSV_REG0413);
+
+ /* lane 3 */
+ reg = readl(regs_base + EXYNOS9_PMA_USBDP_TRSV_REG0813);
+ reg |= TRSV_REG0813_OVRD_LN3_TX_RXD_COMP_EN;
+ reg |= TRSV_REG0813_OVRD_LN3_TX_RXD_EN;
+ writel(reg, regs_base + EXYNOS9_PMA_USBDP_TRSV_REG0813);
+}
+
+static int
+exynos5_usbdrd_usbdp_g2_v4_pma_check_pll_lock(struct exynos5_usbdrd_phy *phy_drd)
+{
+ static const unsigned int timeout_us = 40000;
+ static const unsigned int sleep_us = 40;
+ static const u32 locked = (CMN_REG01C0_ANA_LCPLL_LOCK_DONE |
+ CMN_REG01C0_ANA_LCPLL_AFC_DONE);
+ u32 reg;
+ int err;
+
+ err = readl_poll_timeout(
+ phy_drd->reg_pma + EXYNOS9_PMA_USBDP_CMN_REG01C0,
+ reg, (reg & locked) == locked, sleep_us, timeout_us);
+ if (err)
+ dev_err(phy_drd->dev,
+ "timed out waiting for PLL lock: %#.8x\n", reg);
+
+ return err;
+}
+
+static void
+exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock(struct exynos5_usbdrd_phy *phy_drd)
+{
+ static const unsigned int timeout_us = 40000;
+ static const unsigned int sleep_us = 40;
+ static const u32 locked =
+ (TRSV_REG03C3_LN0_MON_RX_CDR_AFC_DONE
+ | TRSV_REG03C3_LN0_MON_RX_CDR_CAL_DONE
+ | TRSV_REG03C3_LN0_MON_RX_CDR_FLD_PLL_MODE_DONE
+ | TRSV_REG03C3_LN0_MON_RX_CDR_LOCK_DONE);
+ u32 reg;
+ int err;
+
+ err = readl_poll_timeout(
+ phy_drd->reg_pma + EXYNOS9_PMA_USBDP_TRSV_REG03C3,
+ reg, (reg & locked) == locked, sleep_us, timeout_us);
+ if (!err)
+ return;
+
+ dev_err(phy_drd->dev,
+ "timed out waiting for CDR lock (l0): %#.8x, retrying\n", reg);
+
+ /* based on cable orientation, this might be on the other phy port */
+ err = readl_poll_timeout(
+ phy_drd->reg_pma + EXYNOS9_PMA_USBDP_TRSV_REG07C3,
+ reg, (reg & locked) == locked, sleep_us, timeout_us);
+ if (err)
+ dev_err(phy_drd->dev,
+ "timed out waiting for CDR lock (l2): %#.8x\n", reg);
+}
+
+static void exynos5_usbdrd_gs101_pipe3_init(struct exynos5_usbdrd_phy *phy_drd)
+{
+ void __iomem *regs_pma = phy_drd->reg_pma;
+ void __iomem *regs_phy = phy_drd->reg_phy;
+ u32 reg;
+
+ exynos5_usbdrd_usbdp_g2_v4_ctrl_pma_ready(phy_drd);
+
+ /* force aux off */
+ reg = readl(regs_pma + EXYNOS9_PMA_USBDP_CMN_REG0008);
+ reg &= ~CMN_REG0008_AUX_EN;
+ reg |= CMN_REG0008_OVRD_AUX_EN;
+ writel(reg, regs_pma + EXYNOS9_PMA_USBDP_CMN_REG0008);
+
+ exynos5_usbdrd_apply_phy_tunes(phy_drd, PTS_PIPE3_PREINIT);
+ exynos5_usbdrd_apply_phy_tunes(phy_drd, PTS_PIPE3_INIT);
+ exynos5_usbdrd_apply_phy_tunes(phy_drd, PTS_PIPE3_POSTINIT);
+
+ exynos5_usbdrd_usbdp_g2_v4_pma_lane_mux_sel(phy_drd);
+
+ /* reset release from port */
+ reg = readl(regs_phy + EXYNOS850_DRD_SECPMACTL);
+ reg &= ~(SECPMACTL_PMA_TRSV_SW_RST | SECPMACTL_PMA_CMN_SW_RST |
+ SECPMACTL_PMA_INIT_SW_RST);
+ writel(reg, regs_phy + EXYNOS850_DRD_SECPMACTL);
+
+ if (!exynos5_usbdrd_usbdp_g2_v4_pma_check_pll_lock(phy_drd))
+ exynos5_usbdrd_usbdp_g2_v4_pma_check_cdr_lock(phy_drd);
+}
+
static void exynos5_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
{
u32 reg;
@@ -736,10 +1110,29 @@ static const struct phy_ops exynos5_usbdrd_phy_ops = {
.owner = THIS_MODULE,
};
+static void
+exynos5_usbdrd_usb_v3p1_pipe_override(struct exynos5_usbdrd_phy *phy_drd)
+{
+ void __iomem *regs_base = phy_drd->reg_phy;
+ u32 reg;
+
+ /* force pipe3 signal for link */
+ reg = readl(regs_base + EXYNOS850_DRD_LINKCTRL);
+ reg &= ~LINKCTRL_FORCE_PHYSTATUS;
+ reg |= LINKCTRL_FORCE_PIPE_EN | LINKCTRL_FORCE_RXELECIDLE;
+ writel(reg, regs_base + EXYNOS850_DRD_LINKCTRL);
+
+ /* PMA disable */
+ reg = readl(regs_base + EXYNOS850_DRD_SECPMACTL);
+ reg |= SECPMACTL_PMA_LOW_PWR;
+ writel(reg, regs_base + EXYNOS850_DRD_SECPMACTL);
+}
+
static void exynos850_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
{
void __iomem *regs_base = phy_drd->reg_phy;
u32 reg;
+ u32 ss_ports;
/*
* Disable HWACG (hardware auto clock gating control). This will force
@@ -750,8 +1143,16 @@ static void exynos850_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
reg |= LINKCTRL_FORCE_QACT;
writel(reg, regs_base + EXYNOS850_DRD_LINKCTRL);
+ reg = readl(regs_base + EXYNOS850_DRD_LINKPORT);
+ ss_ports = FIELD_GET(LINKPORT_HOST_NUM_U3, reg);
+
/* Start PHY Reset (POR=high) */
reg = readl(regs_base + EXYNOS850_DRD_CLKRST);
+ if (ss_ports) {
+ reg |= CLKRST_PHY20_SW_POR;
+ reg |= CLKRST_PHY20_SW_POR_SEL;
+ reg |= CLKRST_PHY_RESET_SEL;
+ }
reg |= CLKRST_PHY_SW_RST;
writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
@@ -812,6 +1213,10 @@ static void exynos850_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
/* Finish PHY reset (POR=low) */
udelay(10); /* required before doing POR=low */
reg = readl(regs_base + EXYNOS850_DRD_CLKRST);
+ if (ss_ports) {
+ reg |= CLKRST_PHY20_SW_POR_SEL;
+ reg &= ~CLKRST_PHY20_SW_POR;
+ }
reg &= ~(CLKRST_PHY_SW_RST | CLKRST_PORT_RST);
writel(reg, regs_base + EXYNOS850_DRD_CLKRST);
udelay(75); /* required after POR=low for guaranteed PHY clock */
@@ -820,6 +1225,13 @@ static void exynos850_usbdrd_utmi_init(struct exynos5_usbdrd_phy *phy_drd)
reg = readl(regs_base + EXYNOS850_DRD_HSP);
reg &= ~HSP_FSV_OUT_EN;
writel(reg, regs_base + EXYNOS850_DRD_HSP);
+
+ if (ss_ports)
+ exynos5_usbdrd_usb_v3p1_pipe_override(phy_drd);
+
+ if (phy_drd->drv_data->phy_tunes)
+ exynos5_usbdrd_apply_phy_tunes(phy_drd,
+ PTS_UTMI_POSTINIT);
}
static int exynos850_usbdrd_phy_init(struct phy *phy)
@@ -848,6 +1260,9 @@ static int exynos850_usbdrd_phy_exit(struct phy *phy)
u32 reg;
int ret;
+ if (inst->phy_cfg->id != EXYNOS5_DRDPHY_UTMI)
+ return 0;
+
ret = clk_bulk_prepare_enable(phy_drd->n_phy_clks, phy_drd->phy_clks);
if (ret)
return ret;
@@ -884,8 +1299,16 @@ static const struct phy_ops exynos850_usbdrd_phy_ops = {
.owner = THIS_MODULE,
};
+static const struct phy_ops gs101_usbdrd_phy_ops = {
+ .init = exynos850_usbdrd_phy_init,
+ .exit = exynos850_usbdrd_phy_exit,
+ .power_on = exynos5_usbdrd_phy_power_on,
+ .power_off = exynos5_usbdrd_phy_power_off,
+ .owner = THIS_MODULE,
+};
+
static const char * const phy_clk_list[] = {
- "phy",
+ "phy", "ctrl_aclk", "ctrl_pclk", "scl_pclk",
};
static int exynos5_usbdrd_phy_clk_handle(struct exynos5_usbdrd_phy *phy_drd)
@@ -971,6 +1394,150 @@ static const struct exynos5_usbdrd_phy_config phy_cfg_exynos850[] = {
},
};
+static const struct exynos5_usbdrd_phy_config phy_cfg_gs101[] = {
+ {
+ .id = EXYNOS5_DRDPHY_UTMI,
+ .phy_isol = exynos5_usbdrd_phy_isol,
+ .phy_init = exynos850_usbdrd_utmi_init,
+ },
+ {
+ .id = EXYNOS5_DRDPHY_PIPE3,
+ .phy_isol = exynos5_usbdrd_phy_isol,
+ .phy_init = exynos5_usbdrd_gs101_pipe3_init,
+ },
+};
+
+static const struct exynos5_usbdrd_phy_tuning gs101_tunes_utmi_postinit[] = {
+ PHY_TUNING_ENTRY_PHY(EXYNOS850_DRD_HSPPARACON,
+ (HSPPARACON_TXVREF | HSPPARACON_TXRES |
+ HSPPARACON_TXPREEMPAMP | HSPPARACON_SQRX |
+ HSPPARACON_COMPDIS),
+ (FIELD_PREP_CONST(HSPPARACON_TXVREF, 6) |
+ FIELD_PREP_CONST(HSPPARACON_TXRES, 1) |
+ FIELD_PREP_CONST(HSPPARACON_TXPREEMPAMP, 3) |
+ FIELD_PREP_CONST(HSPPARACON_SQRX, 5) |
+ FIELD_PREP_CONST(HSPPARACON_COMPDIS, 7))),
+ PHY_TUNING_ENTRY_LAST
+};
+
+static const struct exynos5_usbdrd_phy_tuning gs101_tunes_pipe3_preinit[] = {
+ /* preinit */
+ /* CDR data mode exit GEN1 ON / GEN2 OFF */
+ PHY_TUNING_ENTRY_PMA(0x0c8c, -1, 0xff),
+ PHY_TUNING_ENTRY_PMA(0x1c8c, -1, 0xff),
+ PHY_TUNING_ENTRY_PMA(0x0c9c, -1, 0x7d),
+ PHY_TUNING_ENTRY_PMA(0x1c9c, -1, 0x7d),
+ /* improve EDS distribution */
+ PHY_TUNING_ENTRY_PMA(0x0e7c, -1, 0x06),
+ PHY_TUNING_ENTRY_PMA(0x09e0, -1, 0x00),
+ PHY_TUNING_ENTRY_PMA(0x09e4, -1, 0x36),
+ PHY_TUNING_ENTRY_PMA(0x1e7c, -1, 0x06),
+ PHY_TUNING_ENTRY_PMA(0x1e90, -1, 0x00),
+ PHY_TUNING_ENTRY_PMA(0x1e94, -1, 0x36),
+ /* improve LVCC */
+ PHY_TUNING_ENTRY_PMA(0x08f0, -1, 0x30),
+ PHY_TUNING_ENTRY_PMA(0x18f0, -1, 0x30),
+ /* LFPS RX VIH shmoo hole */
+ PHY_TUNING_ENTRY_PMA(0x0a08, -1, 0x0c),
+ PHY_TUNING_ENTRY_PMA(0x1a08, -1, 0x0c),
+ /* remove unrelated option for v4 phy */
+ PHY_TUNING_ENTRY_PMA(0x0a0c, -1, 0x05),
+ PHY_TUNING_ENTRY_PMA(0x1a0c, -1, 0x05),
+ /* improve Gen2 LVCC */
+ PHY_TUNING_ENTRY_PMA(0x00f8, -1, 0x1c),
+ PHY_TUNING_ENTRY_PMA(0x00fc, -1, 0x54),
+ /* Change Vth of RCV_DET because of TD 7.40 Polling Retry Test */
+ PHY_TUNING_ENTRY_PMA(0x104c, -1, 0x07),
+ PHY_TUNING_ENTRY_PMA(0x204c, -1, 0x07),
+ /* reduce Ux Exit time, assuming 26MHz clock */
+ /* Gen1 */
+ PHY_TUNING_ENTRY_PMA(0x0ca8, -1, 0x00),
+ PHY_TUNING_ENTRY_PMA(0x0cac, -1, 0x04),
+ PHY_TUNING_ENTRY_PMA(0x1ca8, -1, 0x00),
+ PHY_TUNING_ENTRY_PMA(0x1cac, -1, 0x04),
+ /* Gen2 */
+ PHY_TUNING_ENTRY_PMA(0x0cb8, -1, 0x00),
+ PHY_TUNING_ENTRY_PMA(0x0cbc, -1, 0x04),
+ PHY_TUNING_ENTRY_PMA(0x1cb8, -1, 0x00),
+ PHY_TUNING_ENTRY_PMA(0x1cbc, -1, 0x04),
+ /* RX impedance setting */
+ PHY_TUNING_ENTRY_PMA(0x0bb0, 0x03, 0x01),
+ PHY_TUNING_ENTRY_PMA(0x0bb4, 0xf0, 0xa0),
+ PHY_TUNING_ENTRY_PMA(0x1bb0, 0x03, 0x01),
+ PHY_TUNING_ENTRY_PMA(0x1bb4, 0xf0, 0xa0),
+
+ PHY_TUNING_ENTRY_LAST
+};
+
+static const struct exynos5_usbdrd_phy_tuning gs101_tunes_pipe3_init[] = {
+ /* init */
+ /* abnormal common pattern mask */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_BACK_END_MODE_VEC,
+ BACK_END_MODE_VEC_DISABLE_DATA_MASK, 0),
+ /* de-serializer enabled when U2 */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_OUT_VEC_2, PCS_OUT_VEC_B4_DYNAMIC,
+ PCS_OUT_VEC_B4_SEL_OUT),
+ /* TX Keeper Disable, Squelch on when U3 */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_OUT_VEC_3, PCS_OUT_VEC_B7_DYNAMIC,
+ PCS_OUT_VEC_B7_SEL_OUT | PCS_OUT_VEC_B2_SEL_OUT),
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_NS_VEC_PS1_N1, -1,
+ (FIELD_PREP_CONST(NS_VEC_NS_REQ, 5) |
+ NS_VEC_ENABLE_TIMER |
+ FIELD_PREP_CONST(NS_VEC_SEL_TIMEOUT, 3))),
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_NS_VEC_PS2_N0, -1,
+ (FIELD_PREP_CONST(NS_VEC_NS_REQ, 1) |
+ NS_VEC_ENABLE_TIMER |
+ FIELD_PREP_CONST(NS_VEC_SEL_TIMEOUT, 3) |
+ FIELD_PREP_CONST(NS_VEC_COND_MASK, 2) |
+ FIELD_PREP_CONST(NS_VEC_EXP_COND, 2))),
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_NS_VEC_PS3_N0, -1,
+ (FIELD_PREP_CONST(NS_VEC_NS_REQ, 1) |
+ NS_VEC_ENABLE_TIMER |
+ FIELD_PREP_CONST(NS_VEC_SEL_TIMEOUT, 3) |
+ FIELD_PREP_CONST(NS_VEC_COND_MASK, 7) |
+ FIELD_PREP_CONST(NS_VEC_EXP_COND, 7))),
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_TIMEOUT_0, -1, 112),
+ /* Block Aligner Type B */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_RX_CONTROL, 0,
+ RX_CONTROL_EN_BLOCK_ALIGNER_TYPE_B),
+ /* Block align at TS1/TS2 for Gen2 stability (Gen2 only) */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_RX_CONTROL_DEBUG,
+ RX_CONTROL_DEBUG_NUM_COM_FOUND,
+ (RX_CONTROL_DEBUG_EN_TS_CHECK |
+ /*
+ * increase pcs ts1 adding packet-cnt 1 --> 4
+ * lnx_rx_valid_rstn_delay_rise_sp/ssp :
+ * 19.6us(0x200) -> 15.3us(0x4)
+ */
+ FIELD_PREP_CONST(RX_CONTROL_DEBUG_NUM_COM_FOUND, 4))),
+ /* Gen1 Tx DRIVER pre-shoot, de-emphasis, level ctrl */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_HS_TX_COEF_MAP_0,
+ (HS_TX_COEF_MAP_0_SSTX_DEEMP | HS_TX_COEF_MAP_0_SSTX_LEVEL |
+ HS_TX_COEF_MAP_0_SSTX_PRE_SHOOT),
+ (FIELD_PREP_CONST(HS_TX_COEF_MAP_0_SSTX_DEEMP, 8) |
+ FIELD_PREP_CONST(HS_TX_COEF_MAP_0_SSTX_LEVEL, 0xb) |
+ FIELD_PREP_CONST(HS_TX_COEF_MAP_0_SSTX_PRE_SHOOT, 0))),
+ /* Gen2 Tx DRIVER level ctrl */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_LOCAL_COEF,
+ LOCAL_COEF_PMA_CENTER_COEF,
+ FIELD_PREP_CONST(LOCAL_COEF_PMA_CENTER_COEF, 0xb)),
+ /* Gen2 U1 exit LFPS duration : 900ns ~ 1.2us */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_TIMEOUT_3, -1, 4096),
+ /* set skp_remove_th 0x2 -> 0x7 for avoiding retry problem. */
+ PHY_TUNING_ENTRY_PCS(EXYNOS9_PCS_EBUF_PARAM,
+ EBUF_PARAM_SKP_REMOVE_TH_EMPTY_MODE,
+ FIELD_PREP_CONST(EBUF_PARAM_SKP_REMOVE_TH_EMPTY_MODE, 0x7)),
+
+ PHY_TUNING_ENTRY_LAST
+};
+
+static const struct exynos5_usbdrd_phy_tuning *gs101_tunes[] = {
+ [PTS_UTMI_POSTINIT] = gs101_tunes_utmi_postinit,
+ [PTS_PIPE3_PREINIT] = gs101_tunes_pipe3_preinit,
+ [PTS_PIPE3_INIT] = gs101_tunes_pipe3_init,
+};
+
+
static const struct exynos5_usbdrd_phy_drvdata exynos5420_usbdrd_phy = {
.phy_cfg = phy_cfg_exynos5,
.phy_ops = &exynos5_usbdrd_phy_ops,
@@ -1008,8 +1575,20 @@ static const struct exynos5_usbdrd_phy_drvdata exynos850_usbdrd_phy = {
.has_common_clk_gate = true,
};
+static const struct exynos5_usbdrd_phy_drvdata gs101_usbd31rd_phy = {
+ .phy_cfg = phy_cfg_gs101,
+ .phy_tunes = gs101_tunes,
+ .phy_ops = &gs101_usbdrd_phy_ops,
+ .pmu_offset_usbdrd0_phy = GS101_PHY_CTRL_USB20,
+ .pmu_offset_usbdrd0_phy_ss = GS101_PHY_CTRL_USBDP,
+ .has_common_clk_gate = true,
+};
+
static const struct of_device_id exynos5_usbdrd_phy_of_match[] = {
{
+ .compatible = "google,gs101-usb31drd-phy",
+ .data = &gs101_usbd31rd_phy
+ }, {
.compatible = "samsung,exynos5250-usbdrd-phy",
.data = &exynos5250_usbdrd_phy
}, {
@@ -1048,16 +1627,35 @@ static int exynos5_usbdrd_phy_probe(struct platform_device *pdev)
dev_set_drvdata(dev, phy_drd);
phy_drd->dev = dev;
- phy_drd->reg_phy = devm_platform_ioremap_resource(pdev, 0);
- if (IS_ERR(phy_drd->reg_phy))
- return PTR_ERR(phy_drd->reg_phy);
-
drv_data = of_device_get_match_data(dev);
if (!drv_data)
return -EINVAL;
-
phy_drd->drv_data = drv_data;
+ if (of_property_present(dev->of_node, "reg-names")) {
+ void __iomem *reg;
+
+ reg = devm_platform_ioremap_resource_byname(pdev, "phy");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+ phy_drd->reg_phy = reg;
+
+ reg = devm_platform_ioremap_resource_byname(pdev, "pcs");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+ phy_drd->reg_pcs = reg;
+
+ reg = devm_platform_ioremap_resource_byname(pdev, "pma");
+ if (IS_ERR(reg))
+ return PTR_ERR(reg);
+ phy_drd->reg_pma = reg;
+ } else {
+ /* DTB with just a single region */
+ phy_drd->reg_phy = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(phy_drd->reg_phy))
+ return PTR_ERR(phy_drd->reg_phy);
+ }
+
ret = exynos5_usbdrd_phy_clk_handle(phy_drd);
if (ret) {
dev_err(dev, "Failed to initialize clocks\n");
diff --git a/include/linux/soc/samsung/exynos-regs-pmu.h b/include/linux/soc/samsung/exynos-regs-pmu.h
index aa840ed043e1..6765160eaab2 100644
--- a/include/linux/soc/samsung/exynos-regs-pmu.h
+++ b/include/linux/soc/samsung/exynos-regs-pmu.h
@@ -657,4 +657,8 @@
#define EXYNOS5433_PAD_RETENTION_UFS_OPTION (0x3268)
#define EXYNOS5433_PAD_RETENTION_FSYSGENIO_OPTION (0x32A8)
+/* For GS101 */
+#define GS101_PHY_CTRL_USB20 0x3eb0
+#define GS101_PHY_CTRL_USBDP 0x3eb4
+
#endif /* __LINUX_SOC_EXYNOS_REGS_PMU_H */
--
2.44.0.769.g3c40516874-goog
