Re: [PATCH 2/4] arm64: dts: exynos: gs101: add chipid node

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/02/2024 15:11, Peter Griffin wrote:
> Hi Krzysztof,
> 
> Thanks for your feedback.
> 
> On Tue, 6 Feb 2024 at 10:10, Krzysztof Kozlowski
> <krzysztof.kozlowski@xxxxxxxxxx> wrote:
>>
>> On 05/02/2024 15:36, Peter Griffin wrote:
>>> Hi Alexey & Krysztof,
>>>
>>> On Thu, 1 Feb 2024 at 17:22, Alexey Klimov <alexey.klimov@xxxxxxxxxx> wrote:
>>>>
>>>> Signed-off-by: Alexey Klimov <alexey.klimov@xxxxxxxxxx>
>>>> ---
>>>>  arch/arm64/boot/dts/exynos/google/gs101.dtsi | 5 +++++
>>>>  1 file changed, 5 insertions(+)
>>>>
>>>> diff --git a/arch/arm64/boot/dts/exynos/google/gs101.dtsi b/arch/arm64/boot/dts/exynos/google/gs101.dtsi
>>>> index d838e3a7af6e..156fec2575bc 100644
>>>> --- a/arch/arm64/boot/dts/exynos/google/gs101.dtsi
>>>> +++ b/arch/arm64/boot/dts/exynos/google/gs101.dtsi
>>>> @@ -283,6 +283,11 @@ soc: soc@0 {
>>>>                 #size-cells = <1>;
>>>>                 ranges = <0x0 0x0 0x0 0x40000000>;
>>>>
>>>> +               chipid@10000000 {
>>>> +                       compatible = "google,gs101-chipid";
>>>> +                       reg = <0x10000000 0xd000>;
>>>> +               };
>>>> +
>>>
>>> I was wondering about the 0xd000 size here, as most upstream platforms
>>> use a chipid size of 0x100 or 0x24. I see the downstream gs101 kernel
>>> also uses 0xd000. Looking a bit more, that is because gs-chipid.c also
>>> has support for dumping other areas of the OTP SFR bank like asv table
>>> (offset 0x9000) hpm_asv (offset 0xa000) and hw_tune (0xc000).
>>>
>>> I checked Exynos850 and that also has ASV tables at those same offsets
>>> above, but it currently uses a chipid size of 0x100 upstream.
>>> Exynos-asv.c driver is part of exynos-chipid.c upstream so it seems
>>> reasonable to have the increased size including those SFR registers.
>>> Currently exynos-asv.c driver only supports Exynos5422 upstream.
>>>
>>> @Krzysztof - From a process PoV what is the best/correct thing to do
>>> here? Have the increased size in DT that includes ASV parts of the OTP
>>> bank from the get-go?
>>
>> ChipID so far had only size of 0x30 or something like that. What you
>> refer to does not look like old ChipID but full blown OTP, which also
>> includes ChipID.
> 
> OK so in some previous Exynos SoCs chipid had its own separate memory
> mapped SFRs as well as being present in the OTP area?

None of the Exynos I know, have OTP area. There was only chipid. It
seems that few newer designs come with OTP, in entirely separate address
space. Exynos850 looks like the first which comes with integrated chipid
into OTP, so OTP is not separate address.

> 
>>  Although I am not entirely sure about that, either.
>> Depends whether they share clocks, for example.
> 
> This address is the OTP area, and I can't see chipid regs mentioned
> anywhere else in the memory map other than OTP. Unfortunately there
> are lots of separate docs for different IP blocks, so it isn't just a
> case of searching a giant SoC TRM pdf.
> 
> e850 though looks to be the same (the address defined in DT is the otp
> area), that is one large PDF and the chipid regs aren't mentioned
> anywhere else, Given the chipid reg offset is the same (0x10000000)
> for exynosautov9.dtsi, exynosautov920.dtsi, exynos850.dtsi, exynos7885
> and exynos5433 I suspect this could be the same for all those SoCs as
> well.
> 
>>
>> I don't have any GS101 information so I don't know what's there. It
>> seems you ask me to give you decision based on guessing... If you have
>> one block, so if there is OTP, which contains ChipID, then define OTP.
> 
> I believe there is one block that contains ChipID, therefore based on
> the above info we should define full OTP size?
> 
>> Not ChipID+OTP.
>>
>> I think Exynos850 DTSI is wrong here. That's OTP block, not ChipID.
> 
> Yes agreed, and quite possibly the other Exynos SoCs as well.

If ChipID and OTP are in the same block (in OTP), then assume they both
might need the same clocks or some other resources. Therefore we should
not model them as two separate device nodes ChipID and OTP. Instead
there should be one device node with entire OTP address space, which
should not use ChipID compatible to avoid confusion.

Best regards,
Krzysztof





[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux for Synopsys ARC Processors]    
  • [Linux on Unisoc (RDA Micro) SoCs]     [Linux Actions SoC]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  •   Powered by Linux