All registers of the IP have 32 bits. Use u32 variables when reading
or writing from/to the registers. The purpose of those variables becomes
clearer.
Reviewed-by: Sam Protsenko <semen.protsenko@xxxxxxxxxx>
Signed-off-by: Tudor Ambarus <tudor.ambarus@xxxxxxxxxx>
---
drivers/tty/serial/samsung_tty.c | 79 ++++++++++++++++----------------
1 file changed, 39 insertions(+), 40 deletions(-)
diff --git a/drivers/tty/serial/samsung_tty.c b/drivers/tty/serial/samsung_tty.c
index b9b91ff6a1d7..8b396c950933 100644
--- a/drivers/tty/serial/samsung_tty.c
+++ b/drivers/tty/serial/samsung_tty.c
@@ -199,7 +199,7 @@ static void wr_reg(const struct uart_port *port, u32 reg, u32 val)
/* Byte-order aware bit setting/clearing functions. */
static inline void s3c24xx_set_bit(const struct uart_port *port, int idx,
- unsigned int reg)
+ u32 reg)
{
unsigned long flags;
u32 val;
@@ -212,7 +212,7 @@ static inline void s3c24xx_set_bit(const struct uart_port *port, int idx,
}
static inline void s3c24xx_clear_bit(const struct uart_port *port, int idx,
- unsigned int reg)
+ u32 reg)
{
unsigned long flags;
u32 val;
@@ -245,8 +245,8 @@ static void s3c24xx_serial_rx_enable(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long flags;
- unsigned int ucon, ufcon;
int count = 10000;
+ u32 ucon, ufcon;
uart_port_lock_irqsave(port, &flags);
@@ -269,7 +269,7 @@ static void s3c24xx_serial_rx_disable(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long flags;
- unsigned int ucon;
+ u32 ucon;
uart_port_lock_irqsave(port, &flags);
@@ -591,7 +591,7 @@ static inline const struct s3c2410_uartcfg
}
static int s3c24xx_serial_rx_fifocnt(const struct s3c24xx_uart_port *ourport,
- unsigned long ufstat)
+ u32 ufstat)
{
const struct s3c24xx_uart_info *info = ourport->info;
@@ -663,7 +663,7 @@ static void s3c64xx_start_rx_dma(struct s3c24xx_uart_port *ourport)
static void enable_rx_dma(struct s3c24xx_uart_port *ourport)
{
struct uart_port *port = &ourport->port;
- unsigned int ucon;
+ u32 ucon;
/* set Rx mode to DMA mode */
ucon = rd_regl(port, S3C2410_UCON);
@@ -686,7 +686,7 @@ static void enable_rx_dma(struct s3c24xx_uart_port *ourport)
static void enable_rx_pio(struct s3c24xx_uart_port *ourport)
{
struct uart_port *port = &ourport->port;
- unsigned int ucon;
+ u32 ucon;
/* set Rx mode to DMA mode */
ucon = rd_regl(port, S3C2410_UCON);
@@ -711,13 +711,14 @@ static void s3c24xx_serial_rx_drain_fifo(struct s3c24xx_uart_port *ourport);
static irqreturn_t s3c24xx_serial_rx_chars_dma(void *dev_id)
{
- unsigned int utrstat, received;
struct s3c24xx_uart_port *ourport = dev_id;
struct uart_port *port = &ourport->port;
struct s3c24xx_uart_dma *dma = ourport->dma;
struct tty_struct *tty = tty_port_tty_get(&ourport->port.state->port);
struct tty_port *t = &port->state->port;
struct dma_tx_state state;
+ unsigned int received;
+ u32 utrstat;
utrstat = rd_regl(port, S3C2410_UTRSTAT);
rd_regl(port, S3C2410_UFSTAT);
@@ -759,9 +760,9 @@ static irqreturn_t s3c24xx_serial_rx_chars_dma(void *dev_id)
static void s3c24xx_serial_rx_drain_fifo(struct s3c24xx_uart_port *ourport)
{
struct uart_port *port = &ourport->port;
- unsigned int ufcon, ufstat, uerstat;
unsigned int fifocnt = 0;
int max_count = port->fifosize;
+ u32 ufcon, ufstat, uerstat;
u8 ch, flag;
while (max_count-- > 0) {
@@ -945,7 +946,7 @@ static irqreturn_t s3c64xx_serial_handle_irq(int irq, void *id)
{
const struct s3c24xx_uart_port *ourport = id;
const struct uart_port *port = &ourport->port;
- unsigned int pend = rd_regl(port, S3C64XX_UINTP);
+ u32 pend = rd_regl(port, S3C64XX_UINTP);
irqreturn_t ret = IRQ_HANDLED;
if (pend & S3C64XX_UINTM_RXD_MSK) {
@@ -964,7 +965,7 @@ static irqreturn_t apple_serial_handle_irq(int irq, void *id)
{
const struct s3c24xx_uart_port *ourport = id;
const struct uart_port *port = &ourport->port;
- unsigned int pend = rd_regl(port, S3C2410_UTRSTAT);
+ u32 pend = rd_regl(port, S3C2410_UTRSTAT);
irqreturn_t ret = IRQ_NONE;
if (pend & (APPLE_S5L_UTRSTAT_RXTHRESH | APPLE_S5L_UTRSTAT_RXTO)) {
@@ -983,8 +984,8 @@ static irqreturn_t apple_serial_handle_irq(int irq, void *id)
static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
{
const struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned long ufstat = rd_regl(port, S3C2410_UFSTAT);
- unsigned long ufcon = rd_regl(port, S3C2410_UFCON);
+ u32 ufstat = rd_regl(port, S3C2410_UFSTAT);
+ u32 ufcon = rd_regl(port, S3C2410_UFCON);
if (ufcon & S3C2410_UFCON_FIFOMODE) {
if ((ufstat & info->tx_fifomask) != 0 ||
@@ -999,7 +1000,7 @@ static unsigned int s3c24xx_serial_tx_empty(struct uart_port *port)
/* no modem control lines */
static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port)
{
- unsigned int umstat = rd_reg(port, S3C2410_UMSTAT);
+ u32 umstat = rd_reg(port, S3C2410_UMSTAT);
if (umstat & S3C2410_UMSTAT_CTS)
return TIOCM_CAR | TIOCM_DSR | TIOCM_CTS;
@@ -1009,8 +1010,8 @@ static unsigned int s3c24xx_serial_get_mctrl(struct uart_port *port)
static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
{
- unsigned int umcon = rd_regl(port, S3C2410_UMCON);
- unsigned int ucon = rd_regl(port, S3C2410_UCON);
+ u32 umcon = rd_regl(port, S3C2410_UMCON);
+ u32 ucon = rd_regl(port, S3C2410_UCON);
if (mctrl & TIOCM_RTS)
umcon |= S3C2410_UMCOM_RTS_LOW;
@@ -1030,7 +1031,7 @@ static void s3c24xx_serial_set_mctrl(struct uart_port *port, unsigned int mctrl)
static void s3c24xx_serial_break_ctl(struct uart_port *port, int break_state)
{
unsigned long flags;
- unsigned int ucon;
+ u32 ucon;
uart_port_lock_irqsave(port, &flags);
@@ -1188,7 +1189,7 @@ static void apple_s5l_serial_shutdown(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
- unsigned int ucon;
+ u32 ucon;
ucon = rd_regl(port, S3C2410_UCON);
ucon &= ~(APPLE_S5L_UCON_TXTHRESH_ENA_MSK |
@@ -1214,7 +1215,7 @@ static int s3c64xx_serial_startup(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long flags;
- unsigned int ufcon;
+ u32 ufcon;
int ret;
wr_regl(port, S3C64XX_UINTM, 0xf);
@@ -1259,7 +1260,7 @@ static int apple_s5l_serial_startup(struct uart_port *port)
{
struct s3c24xx_uart_port *ourport = to_ourport(port);
unsigned long flags;
- unsigned int ufcon;
+ u32 ufcon;
int ret;
wr_regl(port, S3C2410_UTRSTAT, APPLE_S5L_UTRSTAT_ALL_FLAGS);
@@ -1344,7 +1345,7 @@ static void s3c24xx_serial_pm(struct uart_port *port, unsigned int level,
static inline int s3c24xx_serial_getsource(struct uart_port *port)
{
const struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned int ucon;
+ u32 ucon;
if (info->num_clks == 1)
return 0;
@@ -1358,7 +1359,7 @@ static void s3c24xx_serial_setsource(struct uart_port *port,
unsigned int clk_sel)
{
const struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned int ucon;
+ u32 ucon;
if (info->num_clks == 1)
return;
@@ -1475,9 +1476,8 @@ static void s3c24xx_serial_set_termios(struct uart_port *port,
struct clk *clk = ERR_PTR(-EINVAL);
unsigned long flags;
unsigned int baud, quot, clk_sel = 0;
- unsigned int ulcon;
- unsigned int umcon;
unsigned int udivslot = 0;
+ u32 ulcon, umcon;
/*
* We don't support modem control lines.
@@ -1759,7 +1759,7 @@ static void s3c24xx_serial_resetport(struct uart_port *port,
const struct s3c2410_uartcfg *cfg)
{
const struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned long ucon = rd_regl(port, S3C2410_UCON);
+ u32 ucon = rd_regl(port, S3C2410_UCON);
ucon &= (info->clksel_mask | info->ucon_mask);
wr_regl(port, S3C2410_UCON, ucon | cfg->ucon);
@@ -1905,7 +1905,7 @@ static int s3c24xx_serial_init_port(struct s3c24xx_uart_port *ourport,
wr_regl(port, S3C64XX_UINTSP, 0xf);
break;
case TYPE_APPLE_S5L: {
- unsigned int ucon;
+ u32 ucon;
ucon = rd_regl(port, S3C2410_UCON);
ucon &= ~(APPLE_S5L_UCON_TXTHRESH_ENA_MSK |
@@ -2109,7 +2109,7 @@ static int s3c24xx_serial_resume_noirq(struct device *dev)
/* restore IRQ mask */
switch (ourport->info->type) {
case TYPE_S3C6400: {
- unsigned int uintm = 0xf;
+ u32 uintm = 0xf;
if (ourport->tx_enabled)
uintm &= ~S3C64XX_UINTM_TXD_MSK;
@@ -2125,7 +2125,7 @@ static int s3c24xx_serial_resume_noirq(struct device *dev)
break;
}
case TYPE_APPLE_S5L: {
- unsigned int ucon;
+ u32 ucon;
int ret;
ret = clk_prepare_enable(ourport->clk);
@@ -2187,10 +2187,10 @@ static const struct dev_pm_ops s3c24xx_serial_pm_ops = {
static struct uart_port *cons_uart;
static int
-s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon)
+s3c24xx_serial_console_txrdy(struct uart_port *port, u32 ufcon)
{
const struct s3c24xx_uart_info *info = s3c24xx_port_to_info(port);
- unsigned long ufstat, utrstat;
+ u32 ufstat, utrstat;
if (ufcon & S3C2410_UFCON_FIFOMODE) {
/* fifo mode - check amount of data in fifo registers... */
@@ -2206,7 +2206,7 @@ s3c24xx_serial_console_txrdy(struct uart_port *port, unsigned int ufcon)
}
static bool
-s3c24xx_port_configured(unsigned int ucon)
+s3c24xx_port_configured(u32 ucon)
{
/* consider the serial port configured if the tx/rx mode set */
return (ucon & 0xf) != 0;
@@ -2221,7 +2221,7 @@ s3c24xx_port_configured(unsigned int ucon)
static int s3c24xx_serial_get_poll_char(struct uart_port *port)
{
const struct s3c24xx_uart_port *ourport = to_ourport(port);
- unsigned int ufstat;
+ u32 ufstat;
ufstat = rd_regl(port, S3C2410_UFSTAT);
if (s3c24xx_serial_rx_fifocnt(ourport, ufstat) == 0)
@@ -2233,8 +2233,8 @@ static int s3c24xx_serial_get_poll_char(struct uart_port *port)
static void s3c24xx_serial_put_poll_char(struct uart_port *port,
unsigned char c)
{
- unsigned int ufcon = rd_regl(port, S3C2410_UFCON);
- unsigned int ucon = rd_regl(port, S3C2410_UCON);
+ u32 ufcon = rd_regl(port, S3C2410_UFCON);
+ u32 ucon = rd_regl(port, S3C2410_UCON);
/* not possible to xmit on unconfigured port */
if (!s3c24xx_port_configured(ucon))
@@ -2250,7 +2250,7 @@ static void s3c24xx_serial_put_poll_char(struct uart_port *port,
static void
s3c24xx_serial_console_putchar(struct uart_port *port, unsigned char ch)
{
- unsigned int ufcon = rd_regl(port, S3C2410_UFCON);
+ u32 ufcon = rd_regl(port, S3C2410_UFCON);
while (!s3c24xx_serial_console_txrdy(port, ufcon))
cpu_relax();
@@ -2261,7 +2261,7 @@ static void
s3c24xx_serial_console_write(struct console *co, const char *s,
unsigned int count)
{
- unsigned int ucon = rd_regl(cons_uart, S3C2410_UCON);
+ u32 ucon = rd_regl(cons_uart, S3C2410_UCON);
unsigned long flags;
bool locked = true;
@@ -2288,11 +2288,9 @@ s3c24xx_serial_get_options(struct uart_port *port, int *baud,
int *parity, int *bits)
{
struct clk *clk;
- unsigned int ulcon;
- unsigned int ucon;
- unsigned int ubrdiv;
unsigned long rate;
unsigned int clk_sel;
+ u32 ulcon, ucon, ubrdiv;
char clk_name[MAX_CLK_NAME_LENGTH];
ulcon = rd_regl(port, S3C2410_ULCON);
@@ -2742,7 +2740,8 @@ static int samsung_early_read(struct console *con, char *s, unsigned int n)
{
struct earlycon_device *dev = con->data;
const struct samsung_early_console_data *data = dev->port.private_data;
- int ch, ufstat, num_read = 0;
+ int num_read = 0;
+ u32 ch, ufstat;
while (num_read < n) {
ufstat = rd_regl(&dev->port, S3C2410_UFSTAT);
--
2.43.0.429.g432eaa2c6b-goog
