Re: [PATCH v2] docs: dt-bindings: add DTS Coding Style document

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Il 20/11/23 15:57, Krzysztof Kozlowski ha scritto:
On 20/11/2023 12:43, AngeloGioacchino Del Regno wrote:
Il 20/11/23 09:40, Krzysztof Kozlowski ha scritto:
Document preferred coding style for Devicetree sources (DTS and DTSI),
to bring consistency among all (sub)architectures and ease in reviews.

Cc: Andrew Davis <afd@xxxxxx>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxx>
Cc: Arnd Bergmann <arnd@xxxxxxxx>
Cc: Bjorn Andersson <andersson@xxxxxxxxxx>
Cc: Geert Uytterhoeven <geert+renesas@xxxxxxxxx>
Cc: Heiko Stuebner <heiko@xxxxxxxxx>
Cc: Konrad Dybcio <konrad.dybcio@xxxxxxxxxx>
Cc: Matthias Brugger <matthias.bgg@xxxxxxxxx>
Cc: Michal Simek <michal.simek@xxxxxxx>
Cc: Neil Armstrong <neil.armstrong@xxxxxxxxxx>
Cc: Nishanth Menon <nm@xxxxxx>
Cc: Olof Johansson <olof@xxxxxxxxx>
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>

---

Merging idea: Rob/DT bindings

Changes in v2
=============
1. Hopefully incorporate entire feedback from comments:
a. Fix \ { => / { (Rob)
b. Name: dts-coding-style (Rob)
c. Exceptions for ordering nodes by name for Renesas and pinctrl (Geert,
     Konrad)
d. Ordering properties by common/vendor (Rob)
e. Array entries in <> (Rob)

2. New chapter: Organizing DTSI and DTS

3. Several grammar fixes (missing articles)

Cc: linux-rockchip@xxxxxxxxxxxxxxxxxxx
Cc: linux-mediatek@xxxxxxxxxxxxxxxxxxx
Cc: linux-samsung-soc@xxxxxxxxxxxxxxx
Cc: linux-amlogic@xxxxxxxxxxxxxxxxxxx
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
Cc: linux-arm-msm@xxxxxxxxxxxxxxx
---
   .../devicetree/bindings/dts-coding-style.rst  | 163 ++++++++++++++++++
   Documentation/devicetree/bindings/index.rst   |   1 +
   2 files changed, 164 insertions(+)
   create mode 100644 Documentation/devicetree/bindings/dts-coding-style.rst

diff --git a/Documentation/devicetree/bindings/dts-coding-style.rst b/Documentation/devicetree/bindings/dts-coding-style.rst
new file mode 100644
index 000000000000..cc7e3b4d1b92
--- /dev/null
+++ b/Documentation/devicetree/bindings/dts-coding-style.rst
@@ -0,0 +1,163 @@
+.. SPDX-License-Identifier: GPL-2.0
+.. _dtscodingstyle:
+
+=====================================
+Devicetree Sources (DTS) Coding Style
+=====================================
+
+When writing Devicetree Sources (DTS) please observe below guidelines.  They
+should be considered complementary to any rules expressed already in Devicetree
+Specification and dtc compiler (including W=1 and W=2 builds).
+
+Individual architectures and sub-architectures can add additional rules, making
+the style stricter.
+
+Naming and Valid Characters
+---------------------------
+
+1. Node and property names are allowed to use only:
+
+   * lowercase characters: [a-z]
+   * digits: [0-9]
+   * dash: -
+
+2. Labels are allowed to use only:
+
+   * lowercase characters: [a-z]
+   * digits: [0-9]
+   * underscore: _
+
+3. Unit addresses should use lowercase hex, without leading zeros (padding).

This is imperative, so: s/should/shall/g

Sure, fine.


+
+4. Hex values in properties, e.g. "reg", should use lowercase hex.  The address
+   part can be padded with leading zeros.
+

Same here, I'd say.... :-)

+Example::
+
+	gpi_dma2: dma-controller@800000 {
+		compatible = "qcom,sm8550-gpi-dma", "qcom,sm6350-gpi-dma";
+		reg = <0x0 0x00800000 0x0 0x60000>;
+	}
+
+Order of Nodes
+--------------
+
+1. Nodes within any bus, thus using unit addresses for children, shall be
+   ordered incrementally by unit address.
+   Alternatively for some sub-architectures, nodes of the same type can be
+   grouped together (e.g. all I2C controllers one after another even if this
+   breaks unit address ordering).
+
+2. Nodes without unit addresses should be ordered alpha-numerically by the node
+   name.  For a few types of nodes, they can be ordered by the main property
+   (e.g. pin configuration states ordered by value of "pins" property).
+
+3. When extending nodes in the board DTS via &label, the entries should be
+   ordered alpha-numerically.
+
+Example::
+

Hmm, comments!

+	// SoC DTSI

....speaking of commenting, should we at least suggest to use C-style comments?

	/* SoC DTSI */

I can switch it to C-style in the example, but we are going with Linux
Coding Style which soon will allow // judging by Linus' statements.


Right. That wasn't a strong opinion anyway, so it's totally okay as well.


+
+	/ {
+		cpus {
+			// ...
+		};
+
+		psci {
+			// ...
+		};
+
+		soc@ {
+			dma: dma-controller@10000 {
+				// ...
+			};
+
+			clk: clock-controller@80000 {
+				// ...
+			};
+		};
+	};
+
+	// Board DTS
+
+	&clk {
+		// ...
+	};
+
+	&dma {
+		// ...
+	};
+
+
+Order of Properties in Device Node
+----------------------------------
+
+Following order of properties in device nodes is preferred:
+
+1. compatible
+2. reg
+3. ranges
+4. Standard/common properties (defined by common bindings, e.g. without
+   vendor-prefixes)
+5. Vendor-specific properties
+6. status (if applicable)
+7. Child nodes, where each node is preceded with a blank line
+
+The "status" property is by default "okay", thus it can be omitted.
+
+Example::
+
+	// SoC DTSI
+
+	usb_1_hsphy: phy@88e3000 {
+		compatible = "qcom,sm8550-snps-eusb2-phy";
+		reg = <0x0 0x088e3000 0x0 0x154>;
+		#phy-cells = <0>;
+		resets = <&gcc GCC_QUSB2PHY_PRIM_BCR>;
+		status = "disabled";
+	};

Since this describes vendor-specific properties and vendor prefixes as well
as standard properties, I think it would be clearer if we use something more
complex that actually contains those as an example.

There's a few. One is MediaTek:

	vdo1_rdma0: dma-controller@1c104000 {
		compatible = "mediatek,mt8195-vdo1-rdma";
		reg = <0 0x1c104000 0 0x1000>;
		#dma-cells = <1>;
		clocks = <&vdosys1 CLK_VDO1_MDP_RDMA0>;
		interrupts = <GIC_SPI 495 IRQ_TYPE_LEVEL_HIGH 0>;
		iommus = <&iommu_vdo M4U_PORT_L2_MDP_RDMA0>;
		power-domains = <&spm MT8195_POWER_DOMAIN_VDOSYS1>;
		mediatek,gce-client-reg = <&gce0 SUBSYS_1c10XXXX 0x4000 0x1000>;
	};

...or other one can be nVidia:

	mipi: mipi@700e3000 {
		compatible = "nvidia,tegra210-mipi";
		reg = <0x0 0x700e3000 0x0 0x100>;
		clocks = <&tegra_car TEGRA210_CLK_MIPI_CAL>;
		clock-names = "mipi-cal";
		power-domains = <&pd_sor>;
		#nvidia,mipi-calibrate-cells = <1>;
	};

...or we could make an example out of fantasy, which could work even better
as far as describing goes.

	/* SoC DTSI */

	device_node: device-class@6789abc {
		compatible = "vendor,device";

Yep. I'll use this, unless checkpatch complains about undocumented
compatible. :) This allows to show the child node.


If checkpatch complains about undocumented compatible, could we perhaps use one
that does actually exist, while still retaining the actual mockup examples?

I understand the eventual concern about somewhat wrongly documenting said device,
but it's also true that this is documentation about something else that is not
related to a specific device (so perhaps a "warning: this is for representation
purposes only, and may contain properties that the devices pointed by the currently
used compatible string may not accept" might work to avoid confusion?).

		reg = <0 0x06789abc 0 0xa123>;
		ranges = <0 0 0x6789abc 0x1000>;
		#dma-cells = <1>;
		clocks = <&clock_controller SOC_CLOCK>;
		clock-names = "dev-clk";
		#vendor,custom-cells = <2>;
		status = "disabled";

		child_node: child-class@100 {
			reg = <0x100 0x200>;
			/* ... */
		};
	};

	/* Board DTS */

	&device_node {
		device-supply = <&board_vreg1>;
		status = "okay";
	}

+
+	// Board DTS
+
+	&usb_1_hsphy {
+		clocks = <&tcsr TCSR_USB2_CLKREF_EN>;
+		clock-names = "ref";
+		status = "okay";
+	};
+
+
+Indentation
+-----------
+
+1. Use indentation according to :ref:`codingstyle`.
+2. For arrays spanning across lines, it is preferred to align the continued
+   entries with opening < from the first line.
+3. Each entry in arrays with multiple cells (e.g. "reg" with two IO addresses)
+   should be enclosed in <>.
+
+Example::
+
+	thermal-sensor@c271000 {
+		compatible = "qcom,sm8550-tsens", "qcom,tsens-v2";
+		reg = <0x0 0x0c271000 0x0 0x1000>,
+		      <0x0 0x0c222000 0x0 0x1000>;
+	};
+
+Organizing DTSI and DTSthat +-----------------------
+
+The DTSI and DTS files should be organized in a way representing the common
+(and re-usable) parts of the hardware.  Typically this means organizing DTSI

                                          ^^^^
There's a double space here, it was probably unintentional.

I think I used everywhere double-spaces. At least this was my intention,
so I will fix single-spaces :)


Oh! Okay, yeah, that also works :-D

Cheers,
Angelo





[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux for Synopsys ARC Processors]    
  • [Linux on Unisoc (RDA Micro) SoCs]     [Linux Actions SoC]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  •   Powered by Linux