Re: [PATCH v3 18/20] arm64: dts: google: Add initial Oriole/pixel 6 board support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Oct 11, 2023 at 1:49 PM Peter Griffin <peter.griffin@xxxxxxxxxx> wrote:
>
> Add initial board support for the Pixel 6 phone code named Oriole. This
> has been tested with a minimal busybox initramfs and boots to a shell.
>
> Signed-off-by: Peter Griffin <peter.griffin@xxxxxxxxxx>
> ---
>  arch/arm64/boot/dts/google/Makefile         |  4 ++
>  arch/arm64/boot/dts/google/gs101-oriole.dts | 79 +++++++++++++++++++++
>  2 files changed, 83 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/google/Makefile
>  create mode 100644 arch/arm64/boot/dts/google/gs101-oriole.dts
>
> diff --git a/arch/arm64/boot/dts/google/Makefile b/arch/arm64/boot/dts/google/Makefile
> new file mode 100644
> index 000000000000..5cea8ff27141
> --- /dev/null
> +++ b/arch/arm64/boot/dts/google/Makefile
> @@ -0,0 +1,4 @@
> +# SPDX-License-Identifier: GPL-2.0
> +
> +dtb-$(CONFIG_ARCH_GOOGLE_TENSOR) += \
> +       gs101-oriole.dtb \
> diff --git a/arch/arm64/boot/dts/google/gs101-oriole.dts b/arch/arm64/boot/dts/google/gs101-oriole.dts
> new file mode 100644
> index 000000000000..3bebca989d34
> --- /dev/null
> +++ b/arch/arm64/boot/dts/google/gs101-oriole.dts
> @@ -0,0 +1,79 @@
> +// SPDX-License-Identifier: GPL-2.0-only
> +/*
> + * Oriole Device Tree
> + *
> + * Copyright 2021-2023 Google,LLC
> + */
> +
> +/dts-v1/;
> +/plugin/;

Why is this needed? Is that really not possible to build this board
dts as actual dtb, not dtbo (and remove this 'plugin' line)? If GS
bootloader is similar to Exynos850 bootloader, it should be possible
to only use dtb, and flash empty dtbo image. Just a thought.

> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include "gs101-pinctrl.h"
> +#include "gs101.dtsi"
> +
> +/ {
> +       model = "Oriole";
> +       compatible = "google,gs101-oriole", "google,gs101";
> +
> +       chosen {
> +               bootargs = "earlycon=exynos4210,mmio32,0x10A00000 console=ttySAC0";

Why is that earlycon is needed here? The serial should work fine (and
actually even better) without that. Might be very useful for debugging
though, but in production dts I'd remove that bit. Also, not sure why
console is needed. Isn't it enough to just have something like:

        stdout-path = &serial_0;

inside of /chosen node?

Btw, why isn't serial node enabled somewhere in this dts?

> +       };
> +
> +       gpio-keys {
> +               compatible = "gpio-keys";
> +               pinctrl-names = "default";
> +               pinctrl-0 = <&key_voldown &key_volup &key_power>;
> +
> +               button-vol-down {
> +                       label = "KEY_VOLUMEDOWN";
> +                       linux,code = <KEY_VOLUMEDOWN>;
> +                       gpios = <&gpa7 3 GPIO_ACTIVE_LOW>;
> +                       wakeup-source;
> +               };
> +
> +               button-vol-up {
> +                       label = "KEY_VOLUMEUP";
> +                       linux,code = <KEY_VOLUMEUP>;
> +                       gpios = <&gpa8 1 GPIO_ACTIVE_LOW>;
> +                       wakeup-source;
> +               };
> +
> +               button-power {
> +                       label = "KEY_POWER";
> +                       linux,code = <KEY_POWER>;
> +                       gpios = <&gpa10 1 GPIO_ACTIVE_LOW>;
> +                       wakeup-source;
> +               };
> +       };
> +};
> +
> +&pinctrl_1 {
> +       key_voldown: key-voldown-pins {
> +               samsung,pins = "gpa7-3";
> +               samsung,pin-function = <0xf>;
> +               samsung,pin-pud = <0>;

Here and further: maybe replace pid-function and pin-pud hard-coded
values with corresponding named constants?

> +               samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
> +       };
> +
> +       key_volup: key-volup-pins {
> +               samsung,pins = "gpa8-1";
> +               samsung,pin-function = <0xf>;
> +               samsung,pin-pud = <0>;
> +               samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
> +       };
> +};
> +
> +&pinctrl_0 {
> +       key_power: key-power-pins {
> +               samsung,pins = "gpa10-1";
> +               samsung,pin-function = <0xf>;
> +               samsung,pin-pud = <0>;
> +               samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
> +       };
> +};
> +
> +&watchdog_cl0 {
> +       timeout-sec = <30>;

No status = "okay" here? The same question goes for wdt_cl1.

> +};
> --
> 2.42.0.655.g421f12c284-goog
>




[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux for Synopsys ARC Processors]    
  • [Linux on Unisoc (RDA Micro) SoCs]     [Linux Actions SoC]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  •   Powered by Linux