On 16/12/2021 20:40, Sam Protsenko wrote:
> On Wed, 15 Dec 2021 at 18:47, Krzysztof Kozlowski
> <krzysztof.kozlowski@xxxxxxxxxxxxx> wrote:
>>
(...)
>>> + serial0 = &serial_0;
>>> + serial1 = &serial_1;
>>> + serial2 = &serial_2;
>>> + i2c0 = &i2c_0;
>>> + i2c1 = &i2c_1;
>>> + i2c2 = &i2c_2;
>>> + i2c3 = &i2c_3;
>>> + i2c4 = &i2c_4;
>>> + i2c5 = &i2c_5;
>>> + i2c6 = &i2c_6;
>>> + i2c7 = &hsi2c_0;
>>> + i2c8 = &hsi2c_1;
>>> + i2c9 = &hsi2c_2;
>>> + i2c10 = &hsi2c_3;
>>> + i2c11 = &hsi2c_4;
>>> + };
>>> +
>>> + arm-pmu {
>>> + compatible = "arm,cortex-a55-pmu";
>>> + interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 108 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 109 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>,
>>> + <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>;
>>> + interrupt-affinity = <&cpu0>, <&cpu1>, <&cpu2>, <&cpu3>,
>>> + <&cpu4>, <&cpu5>, <&cpu6>, <&cpu7>;
>>> + };
>>> +
>>> + /* Main system clock (XTCXO); external, must be 26 MHz */
>>> + oscclk: clock-oscclk {
>>> + compatible = "fixed-clock";
>>> + clock-output-names = "oscclk";
>>> + #clock-cells = <0>;
>>> + };
>>> +
>>> + /* RTC clock (XrtcXTI); external, must be 32.768 kHz */
>>
>> This clock is usually provided by PMIC, so instead I expect updating
>> s2mps11-clk driver. It's not correct to mock it with fixed-clock, but in
>> some cases might be needed. Then I would need an explanation and maybe a
>> TODO note.
>>
>> I wonder if we already discussed this...
>>
>
> Don't really remember discussing that. That's actually something new
> for me :) I was planning to add PMIC support as a part of separate
> activity later, it might not be so easy: S2MPU12 uses I3C connection.
> And RTC clock is not handled even in downstream kernel. So I'll have
> to implement that by PMIC datasheet. I'll keep some TODO comment for
> now, hope it's ok with you?
Assuming it is really coming from the PMIC (should be visible in the
board schematics), it should be using s2mps11-clk. I am fine with
keeping fixed-clock now + TODO note, but please move it to the board
DTS. It's not the property of the SoC.
>
>>> + rtcclk: clock-rtcclk {> + compatible = "fixed-clock";
>>> + clock-output-names = "rtcclk";
>>> + #clock-cells = <0>;
>>> + };
>>> +
Best regards,
Krzysztof
