USIv2 IP-core provides selectable serial protocol (UART, SPI or
High-Speed I2C); only one can be chosen at a time. This series
implements USIv2 driver, which allows one to select particular USI
function in device tree, and also performs USI block initialization.
With that driver implemented, it's not needed to do USI initialization
in protocol drivers anymore, so that code is removed from the serial
driver.
Because USI driver is tristate (can be built as a module), serial driver
was reworked so it's possible to use its console part as a module too.
This way we can load serial driver module from user space and still have
serial console functional.
Make it impossible to build UART/SPI/I2C driver as a built-in when USIv2
driver built as a module: USIv2 configuration must be always done before
tinkering with particular protocol it implements.
Design features:
- "reg" property contains USI registers start address (0xc0 offset);
it's used in the driver to access USI_CON and USI_OPTION registers.
This way all USI initialization (reset, HWACG, etc) can be done in
USIv2 driver separately, rather than duplicating that code over
UART/SPI/I2C drivers
- System Register (system controller node) and its SW_CONF register
offset are provided in "samsung,sysreg" property; it's used to
select USI function (protocol to be used)
- USI function is specified in "samsung,mode" property; integer value
is used to simplify parsing
- there is "samsung,clkreq-on" bool property, which makes driver
disable HWACG control (needed for UART to work properly)
- PCLK and IPCLK clocks are both provided to USI node; apparently both
need to be enabled to access USI registers
- protocol nodes are embedded (as a child nodes) in USI node; it
allows correct init order, and reflects HW properly
- USIv2 driver is a tristate: can be also useful from Android GKI
requirements point of view
- driver functions are implemented with further development in mind:
we might want to add some SysFS interface later for example, or
provide some functions to serial drivers with EXPORT_SYMBOL(), etc;
also another USI revisions could be added (like USIv1)
Changes in v2:
- Renamed all 'usi_v2' wording to just 'usi' everywhere
- Removed patches adding dependency on EXYNOS_USI for UART/I2C/SPI
drivers
- Added patch: "tty: serial: samsung: Fix console registration from
module"
- Combined dt-bindings doc and dt-bindings header patches
- Reworked USI driver to be ready for USIv1 addition
- Improved dt-bindings
- Added USI_V2_NONE mode value
Sam Protsenko (5):
dt-bindings: soc: samsung: Add Exynos USI bindings
soc: samsung: Add USI driver
tty: serial: samsung: Remove USI initialization
tty: serial: samsung: Enable console as module
tty: serial: samsung: Fix console registration from module
.../bindings/soc/samsung/exynos-usi.yaml | 135 +++++++++
drivers/soc/samsung/Kconfig | 14 +
drivers/soc/samsung/Makefile | 2 +
drivers/soc/samsung/exynos-usi.c | 274 ++++++++++++++++++
drivers/tty/serial/Kconfig | 2 +-
drivers/tty/serial/samsung_tty.c | 78 ++---
include/dt-bindings/soc/samsung,exynos-usi.h | 17 ++
include/linux/serial_s3c.h | 9 -
8 files changed, 483 insertions(+), 48 deletions(-)
create mode 100644 Documentation/devicetree/bindings/soc/samsung/exynos-usi.yaml
create mode 100644 drivers/soc/samsung/exynos-usi.c
create mode 100644 include/dt-bindings/soc/samsung,exynos-usi.h
--
2.30.2
