Re: [PATCH 12/12] arm64: dts: exynos: Add Exynos850 SoC support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 30/07/2021 16:49, Sam Protsenko wrote:
> Samsung Exynos850 is ARMv8-based mobile-oriented SoC.
> 
> Features:
>  * CPU: Cortex-A55 Octa (8 cores), up to 2 GHz
>  * Memory interface: LPDDR4/4x 2 channels (12.8 GB/s)
>  * SD/MMC: SD 3.0, eMMC5.1 DDR 8-bit
>  * Modem: 4G LTE, 3G, GSM/GPRS/EDGE
>  * RF: Quad GNSS, WiFi 5 (802.11ac), Bluetooth 5.0
>  * GPU: Mali-G52 MP1
>  * Codec: 1080p 60fps H64, HEVC, JPEG HW Codec
>  * Display: Full HD+ (2520x1080)@60fps LCD
>  * Camera: 16+5MP/13+8MP ISP, MIPI CSI 4/4/2, FD, DRC
>  * Connectivity: USB 2.0 DRD, USI (SPI/UART/I2C), HSI2C, I3C, ADC, Audio

Please document first the features you add (and are working) and
afterwards mention all others capabilities.

> 
> This patch adds minimal SoC support. Particular board device tree files
> can include exynos850.dtsi file to get SoC related nodes, and then
> reference those nodes further as needed.
> 
> Signed-off-by: Sam Protsenko <semen.protsenko@xxxxxxxxxx>
> ---
>  .../boot/dts/exynos/exynos850-pinctrl.dtsi    | 782 ++++++++++++++++++
>  arch/arm64/boot/dts/exynos/exynos850-usi.dtsi |  30 +
>  arch/arm64/boot/dts/exynos/exynos850.dtsi     | 245 ++++++

Not buildable. Missing Makefile, missing DTS. Please submit with initial
DTS, otherwise no one is able to verify it even compiles.

>  3 files changed, 1057 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850-usi.dtsi
>  create mode 100644 arch/arm64/boot/dts/exynos/exynos850.dtsi
> 
> diff --git a/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> new file mode 100644
> index 000000000000..4cf0a22cc6db
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850-pinctrl.dtsi
> @@ -0,0 +1,782 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos850 SoC pin-mux and pin-config device tree source
> + *
> + * Copyright (C) 2017 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung's Exynos850 SoC pin-mux and pin-config options are listed as device
> + * tree nodes in this file.
> + */
> +
> +#include <dt-bindings/interrupt-controller/exynos850.h>
> +
> +/ {
> +	/* ALIVE */
> +	pinctrl@11850000 {
> +		gpa0: gpa0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;

That's odd a little, why three cells? How this would be used/referenced?

> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			    <GIC_SPI INTREQ__ALIVE_EINT0 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT1 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT2 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT3 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT4 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT5 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT6 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT7 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpa1: gpa1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			    <GIC_SPI INTREQ__ALIVE_EINT8 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT9 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT10 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT11 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT12 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT13 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT14 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT15 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpa2: gpa2 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			    <GIC_SPI INTREQ__ALIVE_EINT16 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT17 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT18 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT19 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT20 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT21 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT22 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT23 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpa3: gpa3 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			    <GIC_SPI INTREQ__ALIVE_EINT24 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT25 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT26 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT27 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT28 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT29 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT30 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT31 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpa4: gpa4 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			    <GIC_SPI INTREQ__ALIVE_EINT32 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT33 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT34 IRQ_TYPE_LEVEL_HIGH>,
> +			    <GIC_SPI INTREQ__ALIVE_EINT35 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpq0: gpq0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		/* USI_PERI_UART_DBG */
> +		uart0_bus: uart0-bus {
> +			samsung,pins = "gpq0-0", "gpq0-1";
> +			samsung,pin-function = <2>;

EXYNOS_PIN_FUNC_2

> +			samsung,pin-pud = <0>;

EXYNOS_PIN_PULL_xx?

> +		};
> +
> +		decon_f_te_on: decon_f_te_on {

1. Where is it used?
2. Use hyphens in node names.
Please build it with W=1 and fix the warnings.

> +			samsung,pins = "gpa4-1";

Order the nodes based on first pin name, so:
i2c5_bus
i2c6_bus
decon_f_te_on
uart0_bus

> +			samsung,pin-function = <0xf>;
> +		};
> +
> +		decon_f_te_off: decon_f_te_off {

Where is it used?

> +			samsung,pins = "gpa4-1";
> +			samsung,pin-function = <0x0>;
> +		};
> +
> +		/* I2C_5 | CAM_PMIC_I2C */

This comment is confusing. I2C-5 is obvious from node name and label.
CAM_PMIC_I2C does not look like property of SoC but board.

> +		i2c5_bus: i2c5-bus {
> +			samsung,pins = "gpa3-5", "gpa3-6";
> +			samsung,pin-function = <3>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* I2C_6 | MOTOR_I2C */
> +		i2c6_bus: i2c6-bus {
> +			samsung,pins = "gpa3-7", "gpa4-0";
> +			samsung,pin-function = <3>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +	};
> +
> +	/* CMGP */
> +	pinctrl@11c30000 {
> +		gpm0: gpm0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			  <GIC_SPI INTREQ__CMGP_EXT_INTM00 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpm1: gpm1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			  <GIC_SPI INTREQ__CMGP_EXT_INTM01 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpm2: gpm2 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			  <GIC_SPI INTREQ__CMGP_EXT_INTM02 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpm3: gpm3 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			  <GIC_SPI INTREQ__CMGP_EXT_INTM03 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpm4: gpm4 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			  <GIC_SPI INTREQ__CMGP_EXT_INTM04 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		gpm5: gpm5 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <3>;
> +			interrupt-parent = <&gic>;
> +			interrupts =
> +			  <GIC_SPI INTREQ__CMGP_EXT_INTM05 IRQ_TYPE_LEVEL_HIGH>;
> +		};
> +
> +		/* usi_cmgp00 */
> +		hsi2c3_bus: hsi2c3-bus {
> +			samsung,pins = "gpm0-0", "gpm1-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* usi_cmgp01 */
> +		hsi2c4_bus: hsi2c4-bus {
> +			samsung,pins = "gpm4-0", "gpm5-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* spi usi_cmgp00 */
> +		spi1_bus: spi1-bus {
> +			samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		spi1_cs: spi1-cs {
> +			samsung,pins = "gpm3-0";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		spi1_cs_func: spi1-cs-func {
> +			samsung,pins = "gpm3-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* spi usi_cmgp01 */
> +		spi2_bus: spi2-bus {
> +			samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		spi2_cs: spi2-cs {
> +			samsung,pins = "gpm7-0";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		spi2_cs_func: spi2-cs-func {
> +			samsung,pins = "gpm7-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* usi_cmgp00_uart */
> +		uart1_bus_single: uart1-bus {
> +			samsung,pins = "gpm0-0", "gpm1-0", "gpm2-0", "gpm3-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +		};
> +
> +		uart1_bus_dual: uart1-bus-dual {
> +			samsung,pins = "gpm0-0", "gpm1-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +		};
> +
> +		/* usi_cmgp01_uart */
> +		uart2_bus_single: uart2-bus {
> +			samsung,pins = "gpm4-0", "gpm5-0", "gpm6-0", "gpm7-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +		};
> +
> +		uart2_bus_dual: uart2-bus-dual {
> +			samsung,pins = "gpm4-0", "gpm5-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +		};
> +	};
> +
> +	/* AUD */
> +	pinctrl@14a60000 {
> +		gpb0: gpb0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpb1: gpb1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		aud_codec_mclk: aud-codec-mclk {
> +			samsung,pins = "gpb0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_codec_mclk_idle: aud-codec-mclk-idle {
> +			samsung,pins = "gpb0-0";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_i2s0_bus: aud-i2s0-bus {
> +			samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_i2s0_idle: aud-i2s0-idle {
> +			samsung,pins = "gpb0-1", "gpb0-2", "gpb0-3", "gpb0-4";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_i2s1_bus: aud-i2s1-bus {
> +			samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_i2s1_idle: aud-i2s1-idle {
> +			samsung,pins = "gpb1-0", "gpb1-1", "gpb1-2", "gpb1-3";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_fm_bus: aud-fm-bus {
> +			samsung,pins = "gpb1-4";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <1>;
> +		};
> +
> +		aud_fm_idle: aud-fm-idle {
> +			samsung,pins = "gpb1-4";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <1>;
> +		};
> +	};
> +
> +	/* HSI */
> +	pinctrl@13430000 {
> +		gpf2: gpf2 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		sd2_clk: sd2-clk {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sd2_cmd: sd2-cmd {
> +			samsung,pins = "gpf2-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <2>;
> +		 };
> +
> +		sd2_bus1: sd2-bus-width1 {
> +			samsung,pins = "gpf2-2";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sd2_bus4: sd2-bus-width4 {
> +			samsung,pins = "gpf2-3", "gpf2-4", "gpf2-5";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sd2_clk_fast_slew_rate_1x: sd2-clk_fast_slew_rate_1x {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		sd2_clk_fast_slew_rate_1_5x: sd2-clk_fast_slew_rate_1_5x {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <1>;
> +		};
> +
> +		sd2_clk_fast_slew_rate_2x: sd2-clk_fast_slew_rate_2x {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sd2_clk_fast_slew_rate_2_5x: sd2-clk_fast_slew_rate_2_5x {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd2_clk_fast_slew_rate_3x: sd2-clk_fast_slew_rate_3x {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <4>;
> +		};
> +
> +		sd2_clk_fast_slew_rate_4x: sd2-clk_fast_slew_rate_4x {
> +			samsung,pins = "gpf2-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <5>;
> +		};
> +
> +		sd2_pins_as_pdn: sd2-pins-as-pdn {
> +			samsung,pins = "gpf2-0", "gpf2-1", "gpf2-2", "gpf2-3",
> +				       "gpf2-4", "gpf2-5";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <2>;
> +		};
> +

No need for blank line.

> +	};
> +
> +	/* CORE */
> +	pinctrl@12070000 {
> +		gpf0: gpf0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		sd0_clk: sd0-clk {
> +			samsung,pins = "gpf0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd0_cmd: sd0-cmd {
> +			samsung,pins = "gpf0-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd0_rdqs: sd0-rdqs {
> +			samsung,pins = "gpf0-2";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <1>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd0_nreset: sd0-nreset {
> +			samsung,pins = "gpf0-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd0_clk_fast_slew_rate_1x: sd0-clk_fast_slew_rate_1x {
> +			samsung,pins = "gpf0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <1>;
> +		};
> +
> +		sd0_clk_fast_slew_rate_2x: sd0-clk_fast_slew_rate_2x {
> +			samsung,pins = "gpf0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sd0_clk_fast_slew_rate_3x: sd0-clk_fast_slew_rate_3x {
> +			samsung,pins = "gpf0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sd0_clk_fast_slew_rate_4x: sd0-clk_fast_slew_rate_4x {
> +			samsung,pins = "gpf0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		gpf1: gpf1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		sd0_bus1: sd0-bus-width1 {
> +			samsung,pins = "gpf1-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd0_bus4: sd0-bus-width4 {
> +			samsung,pins = "gpf1-1", "gpf1-2", "gpf1-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <3>;
> +		};
> +
> +		sd0_bus8: sd0-bus-width8 {
> +			samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <3>;
> +		};
> +	};
> +
> +	/* PERI */
> +	pinctrl@139b0000 {
> +		gpg0: gpg0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpp0: gpp0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +		gpp1: gpp1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpp2: gpp2 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpg1: gpg1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpg2: gpg2 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpg3: gpg3 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpc0: gpc0 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		gpc1: gpc1 {
> +			gpio-controller;
> +			#gpio-cells = <2>;
> +
> +			interrupt-controller;
> +			#interrupt-cells = <2>;
> +		};
> +
> +		xclkout: xclkout {
> +			samsung,pins = "gpq0-2";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +		};
> +
> +		/* usi_hsi2c_0 */

Comment seems to duplicate node name/label.

> +		hsi2c0_bus: hsi2c0-bus {
> +			samsung,pins = "gpc1-0", "gpc1-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* usi_hsi2c_1 */
> +		hsi2c1_bus: hsi2c1-bus {
> +			samsung,pins = "gpc1-2", "gpc1-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* usi_hsi2c_2 */
> +		hsi2c2_bus: hsi2c2-bus {
> +			samsung,pins = "gpc1-4", "gpc1-5";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		/* usi_spi_0 */
> +		spi0_bus: spi0-bus {
> +			samsung,pins = "gpp2-0", "gpp2-2", "gpp2-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		spi0_cs: spi0-cs {
> +			samsung,pins = "gpp2-1";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		spi0_cs_func: spi0-cs-func {
> +			samsung,pins = "gpp2-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		i2c0_bus: i2c0-bus {
> +			samsung,pins = "gpp0-0", "gpp0-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		i2c1_bus: i2c1-bus {
> +			samsung,pins = "gpp0-2", "gpp0-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		i2c2_bus: i2c2-bus {
> +			samsung,pins = "gpp0-4", "gpp0-5";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		i2c3_bus: i2c3-bus {
> +			samsung,pins = "gpp1-0", "gpp1-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		i2c4_bus: i2c4-bus {
> +			samsung,pins = "gpp1-2", "gpp1-3";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <3>;
> +			samsung,pin-drv = <0>;
> +		};
> +
> +		fm_lna_en: fm-lna-en {
> +			samsung,pins = "gpg2-3";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-val = <0>;
> +		};
> +
> +		sensor_mclk0_in: sensor-mclk0-in {
> +			samsung,pins = "gpc0-0";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk0_out: sensor-mclk0-out {
> +			samsung,pins = "gpc0-0";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <1>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk0_fn: sensor-mclk0-fn {

No, seriously. What sensor is it? In SoC?

> +			samsung,pins = "gpc0-0";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk1_in: sensor-mclk1-in {
> +			samsung,pins = "gpc0-1";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk1_out: sensor-mclk1-out {
> +			samsung,pins = "gpc0-1";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <1>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk1_fn: sensor-mclk1-fn {
> +			samsung,pins = "gpc0-1";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk2_in: sensor-mclk2-in {
> +			samsung,pins = "gpc0-2";
> +			samsung,pin-function = <0>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk2_out: sensor-mclk2-out {
> +			samsung,pins = "gpc0-2";
> +			samsung,pin-function = <1>;
> +			samsung,pin-pud = <1>;
> +			samsung,pin-drv = <2>;
> +		};
> +
> +		sensor_mclk2_fn: sensor-mclk2-fn {
> +			samsung,pins = "gpc0-2";
> +			samsung,pin-function = <2>;
> +			samsung,pin-pud = <0>;
> +			samsung,pin-drv = <2>;
> +		};
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/exynos/exynos850-usi.dtsi b/arch/arm64/boot/dts/exynos/exynos850-usi.dtsi
> new file mode 100644
> index 000000000000..fb243e0a6260
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850-usi.dtsi
> @@ -0,0 +1,30 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung's Exynos850 SoC USI device tree source
> + *
> + * Copyright (C) 2019 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung's Exynos850 SoC USI channels are listed in this file as device tree
> + * nodes.

Why here not in exynos850.dtsi?

> + */
> +
> +#include <dt-bindings/clock/exynos850.h>
> +
> +/ {
> +	aliases {
> +		uart0 = &serial_0;
> +	};
> +
> +	/* USI_UART */
> +	serial_0: uart@13820000 {

This should ne in soc node.

> +		compatible = "samsung,exynos850-uart";
> +		reg = <0x0 0x13820000 0x100>;
> +		interrupts = <GIC_SPI INTREQ__UART IRQ_TYPE_LEVEL_HIGH>;
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&uart0_bus>;
> +		clocks = <&clock GATE_UART_QCH>, <&clock DOUT_UART>;
> +		clock-names = "gate_uart_clk0", "uart";
> +		status = "disabled";
> +	};
> +};
> diff --git a/arch/arm64/boot/dts/exynos/exynos850.dtsi b/arch/arm64/boot/dts/exynos/exynos850.dtsi
> new file mode 100644
> index 000000000000..ed2d1c8ae0c3
> --- /dev/null
> +++ b/arch/arm64/boot/dts/exynos/exynos850.dtsi
> @@ -0,0 +1,245 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Samsung Exynos850 SoC device tree source
> + *
> + * Copyright (C) 2018 Samsung Electronics Co., Ltd.
> + * Copyright (C) 2021 Linaro Ltd.
> + *
> + * Samsung Exynos850 SoC device nodes are listed in this file.
> + * Exynos based board files can include this file and provide
> + * values for board specific bindings.
> + */
> +
> +#include <dt-bindings/interrupt-controller/exynos850.h>
> +#include <dt-bindings/clock/exynos850.h>
> +#include "exynos850-pinctrl.dtsi"
> +#include "exynos850-usi.dtsi"
> +
> +/ {

Add a comment like:
/* Also known under engineering name exynos3830 */

> +	compatible = "samsung,exynos850";

Undocumented compatible. Checkpatch should complain.

> +	interrupt-parent = <&gic>;
> +	#address-cells = <2>;
> +	#size-cells = <1>;
> +
> +	aliases {
> +		pinctrl0 = &pinctrl_0;
> +		pinctrl1 = &pinctrl_1;
> +		pinctrl2 = &pinctrl_2;
> +		pinctrl3 = &pinctrl_3;
> +		pinctrl4 = &pinctrl_4;
> +		pinctrl5 = &pinctrl_5;
> +	};
> +
> +	cpus {
> +		#address-cells = <2>;
> +		#size-cells = <0>;
> +
> +		cpu-map {
> +			cluster0 {
> +				core0 {
> +					cpu = <&cpu0>;
> +				};
> +				core1 {
> +					cpu = <&cpu1>;
> +				};
> +				core2 {
> +					cpu = <&cpu2>;
> +				};
> +				core3 {
> +					cpu = <&cpu3>;
> +				};
> +			};
> +
> +			cluster1 {
> +				core0 {
> +					cpu = <&cpu4>;
> +				};
> +				core1 {
> +					cpu = <&cpu5>;
> +				};
> +				core2 {
> +					cpu = <&cpu6>;
> +				};
> +				core3 {
> +					cpu = <&cpu7>;
> +				};
> +			};
> +		};
> +
> +		cpu0: cpu@0000 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0000>;

reg = <0x0 0x0>;
(in following places similarly)

> +			enable-method = "psci";
> +		};
> +		cpu1: cpu@0001 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0001>;
> +			enable-method = "psci";
> +		};
> +		cpu2: cpu@0002 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0002>;
> +			enable-method = "psci";
> +		};
> +		cpu3: cpu@0003 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0003>;
> +			enable-method = "psci";
> +		};
> +		cpu4: cpu@0004 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0100>;
> +			enable-method = "psci";
> +		};
> +		cpu5: cpu@0005 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0101>;
> +			enable-method = "psci";
> +		};
> +		cpu6: cpu@0006 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0102>;
> +			enable-method = "psci";
> +		};
> +		cpu7: cpu@0007 {
> +			device_type = "cpu";
> +			compatible = "arm,cortex-a55", "arm,armv8";
> +			reg = <0x0 0x0103>;
> +			enable-method = "psci";
> +		};
> +	};
> +
> +	psci {
> +		compatible = "arm,psci-1.0";
> +		method = "smc";
> +	};
> +
> +	gic: interrupt-controller@12a00000 {
> +		compatible = "arm,cortex-a15-gic", "arm,cortex-a9-gic";
> +		#interrupt-cells = <3>;
> +		#address-cells = <0>;
> +		interrupt-controller;
> +		reg = <0x0 0x12a01000 0x1000>,
> +		      <0x0 0x12a02000 0x1000>,
> +		      <0x0 0x12a04000 0x2000>,
> +		      <0x0 0x12a06000 0x2000>;
> +		interrupts = <GIC_PPI 9
> +				(GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
> +	};
> +
> +	timer {
> +		compatible = "arm,armv8-timer";
> +		interrupts = <GIC_PPI 13
> +				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 14
> +				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 11
> +				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>,
> +			     <GIC_PPI 10
> +				(GIC_CPU_MASK_SIMPLE(8) | IRQ_TYPE_LEVEL_LOW)>;
> +		clock-frequency = <26000000>;
> +		use-clocksource-only;
> +		use-physical-timer;
> +	};
> +

All below should be under soc node.

Please don't write new DTS/DTSI from scratch but use exynos5433.dtsi as
template/example.

> +	clock: clock-controller@0x120e0000 {
> +		compatible = "samsung,exynos850-clock";
> +		reg = <0x0 0x120e0000 0x8000>;
> +		#clock-cells = <1>;
> +	};
> +
> +	/* ALIVE */
> +	pinctrl_0: pinctrl@11850000 {
> +		compatible = "samsung,exynos850-pinctrl";
> +		reg = <0x0 0x11850000 0x1000>;
> +		interrupts = <GIC_SPI INTREQ__ALIVE_EINT0 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT1 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT2 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT3 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT4 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT5 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT6 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT7 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT8 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT9 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT10 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT11 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT12 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT13 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT14 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT15 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT16 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT17 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT18 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT19 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT20 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT21 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT22 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT23 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT24 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT25 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT26 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT27 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT28 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT29 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT30 IRQ_TYPE_LEVEL_HIGH>,
> +			     <GIC_SPI INTREQ__ALIVE_EINT31 IRQ_TYPE_LEVEL_HIGH>;
> +
> +		wakeup-interrupt-controller {
> +			compatible = "samsung,exynos7-wakeup-eint";
> +		};
> +	};
> +
> +	/* CMGP */
> +	pinctrl_1: pinctrl@11c30000 {
> +		compatible = "samsung,exynos850-pinctrl";
> +		reg = <0x0 0x11c30000 0x1000>;
> +		interrupts =
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM00 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM01 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM02 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM03 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM04 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM05 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM06 IRQ_TYPE_LEVEL_HIGH>,
> +			<GIC_SPI INTREQ__CMGP_EXT_INTM07 IRQ_TYPE_LEVEL_HIGH>;
> +
> +		wakeup-interrupt-controller {
> +			compatible = "samsung,exynos7-wakeup-eint";
> +		};
> +	};
> +
> +	/* AUD */
> +	pinctrl_2: pinctrl@14a60000 {
> +		compatible = "samsung,exynos850-pinctrl";
> +		reg = <0x0 0x14a60000 0x1000>;
> +	};
> +
> +	/* HSI */
> +	pinctrl_3: pinctrl@13430000 {
> +		compatible = "samsung,exynos850-pinctrl";
> +		reg = <0x0 0x13430000 0x1000>;
> +		interrupts = <GIC_SPI INTREQ__GPIO_HSI IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	/* CORE */
> +	pinctrl_4: pinctrl@12070000 {
> +		compatible = "samsung,exynos850-pinctrl";
> +		reg = <0x0 0x12070000 0x1000>;
> +		interrupts = <GIC_SPI INTREQ__GPIO_CORE IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +
> +	/* PERI */
> +	pinctrl_5: pinctrl@139b0000 {
> +		compatible = "samsung,exynos850-pinctrl";
> +		reg = <0x0 0x139b0000 0x1000>;
> +		interrupts = <GIC_SPI INTREQ__GPIO_PERI IRQ_TYPE_LEVEL_HIGH>;
> +	};
> +};
> 


Best regards,
Krzysztof



[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux for Synopsys ARC Processors]    
  • [Linux on Unisoc (RDA Micro) SoCs]     [Linux Actions SoC]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  •   Powered by Linux