Re: [PATCH v2 7/9] spi: spi-s3c64xx: Ensure cur_speed holds actual clock value

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Aug 24, 2020 at 3:17 PM Lukasz Stelmach <l.stelmach@xxxxxxxxxxx> wrote:
>
> It was <2020-08-22 sob 14:43>, when Krzysztof Kozlowski wrote:
> > On Fri, Aug 21, 2020 at 06:13:59PM +0200, Łukasz Stelmach wrote:
> >> cur_speed is used to calculate transfer timeout and needs to be
> >> set to the actual value of (half) the clock speed for precise
> >> calculations.
> >
> > If you need this only for timeout calculation just divide it in
> > s3c64xx_wait_for_dma().
>
> I divide it here to keep the relationship between the value the variable
> holds and the one that is inside clk_* (See? It's multiplied 3 lines
> above). If you look around every single clk_get_rate() call in the file is
> divided by two.
>
> > Otherwise why only if (cmu) case is updated?
>
> You are righ I will update that too.
>
> However, I wonder if it is even possible that the value read from
> S3C64XX_SPI_CLK_CFG would be different than the one written to it?
>

It is not possible for the register itself, but please see my other
reply, where I explained the integer rounding error which can happen
when calculating the value to write to the register.

> > You are also affecting here not only timeout but
> > s3c64xx_enable_datapath() which is not mentioned in commit log. In other
> > words, this looks wrong.
>
> Indeed, there is a reference too. I've corrected the message.
>

Thanks!

Best regards,
Tomasz

> >>
> >> Cc: Tomasz Figa <tfiga@xxxxxxxxxxxx>
> >> Signed-off-by: Łukasz Stelmach <l.stelmach@xxxxxxxxxxx>
> >> ---
> >>  drivers/spi/spi-s3c64xx.c | 1 +
> >>  1 file changed, 1 insertion(+)
> >>
> >> diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c
> >> index 02de734b8ab1..89c162efe355 100644
> >> --- a/drivers/spi/spi-s3c64xx.c
> >> +++ b/drivers/spi/spi-s3c64xx.c
> >> @@ -626,6 +626,7 @@ static int s3c64xx_spi_config(struct s3c64xx_spi_driver_data *sdd)
> >>              ret = clk_set_rate(sdd->src_clk, sdd->cur_speed * 2);
> >>              if (ret)
> >>                      return ret;
> >> +            sdd->cur_speed = clk_get_rate(sdd->src_clk) / 2;
> >>      } else {
> >>              /* Configure Clock */
> >>              val = readl(regs + S3C64XX_SPI_CLK_CFG);
> >> --
> >> 2.26.2
> >>
> >
> >
>
> --
> Łukasz Stelmach
> Samsung R&D Institute Poland
> Samsung Electronics




[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux for Synopsys ARC Processors]    
  • [Linux on Unisoc (RDA Micro) SoCs]     [Linux Actions SoC]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  •   Powered by Linux