On Tue, Feb 11, 2020 at 11:56:12AM +0100, Marek Szyprowski wrote: > Hi > > On 08.01.2020 16:17, Mathias Nyman wrote: > > xhci driver assumed that xHC controllers have at most one custom > > supported speed table (PSI) for all usb 3.x ports. > > Memory was allocated for one PSI table under the xhci hub structure. > > > > Turns out this is not the case, some controllers have a separate > > "supported protocol capability" entry with a PSI table for each port. > > This means each usb3 port can in theory support different custom speeds. > > > > To solve this cache all supported protocol capabilities with their PSI > > tables in an array, and add pointers to the xhci port structure so that > > every port points to its capability entry in the array. > > > > When creating the SuperSpeedPlus USB Device Capability BOS descriptor > > for the xhci USB 3.1 roothub we for now will use only data from the > > first USB 3.1 capable protocol capability entry in the array. > > This could be improved later, this patch focuses resolving > > the memory leak. > > > > Reported-by: Paul Menzel <pmenzel@xxxxxxxxxxxxx> > > Reported-by: Sajja Venkateswara Rao <VenkateswaraRao.Sajja@xxxxxxx> > > Signed-off-by: Mathias Nyman <mathias.nyman@xxxxxxxxxxxxxxx> > > This patch landed in today's linux-next (20200211) and causes NULL > pointer dereference during second suspend/resume cycle on Samsung > Exynos5422-based (arm 32bit) Odroid XU3lite board: > > # time rtcwake -s10 -mmem > rtcwake: wakeup from "mem" using /dev/rtc0 at Tue Feb 11 10:51:43 2020 > PM: suspend entry (deep) > Filesystems sync: 0.012 seconds > Freezing user space processes ... (elapsed 0.010 seconds) done. > OOM killer disabled. > Freezing remaining freezable tasks ... (elapsed 0.002 seconds) done. > smsc95xx 1-1.1:1.0 eth0: entering SUSPEND2 mode > wake enabled for irq 153 > wake enabled for irq 158 > samsung-pinctrl 13400000.pinctrl: Setting external wakeup interrupt > mask: 0xffffffe7 > Disabling non-boot CPUs ... > IRQ 51: no longer affine to CPU1 > IRQ 52: no longer affine to CPU2 > s3c2410-wdt 101d0000.watchdog: watchdog disabled > wake disabled for irq 158 > usb usb1: root hub lost power or was reset > usb usb2: root hub lost power or was reset > wake disabled for irq 153 > exynos-tmu 10060000.tmu: More trip points than supported by this TMU. > exynos-tmu 10060000.tmu: 2 trip points should be configured in polling mode. > exynos-tmu 10064000.tmu: More trip points than supported by this TMU. > exynos-tmu 10064000.tmu: 2 trip points should be configured in polling mode. > exynos-tmu 10068000.tmu: More trip points than supported by this TMU. > exynos-tmu 10068000.tmu: 2 trip points should be configured in polling mode. > exynos-tmu 1006c000.tmu: More trip points than supported by this TMU. > exynos-tmu 1006c000.tmu: 2 trip points should be configured in polling mode. > exynos-tmu 100a0000.tmu: More trip points than supported by this TMU. > exynos-tmu 100a0000.tmu: 6 trip points should be configured in polling mode. > usb usb3: root hub lost power or was reset > s3c-rtc 101e0000.rtc: rtc disabled, re-enabling > usb usb4: root hub lost power or was reset > xhci-hcd xhci-hcd.8.auto: No ports on the roothubs? > PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -12 > PM: Device xhci-hcd.8.auto failed to resume async: error -12 > hub 3-0:1.0: hub_ext_port_status failed (err = -32) > hub 4-0:1.0: hub_ext_port_status failed (err = -32) > usb 1-1: reset high-speed USB device number 2 using exynos-ehci > usb 1-1.1: reset high-speed USB device number 3 using exynos-ehci > OOM killer enabled. > Restarting tasks ... done. > > real 0m11.890s > user 0m0.001s > sys 0m0.679s > root@target:~# PM: suspend exit > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 400000Hz, > actual 396825HZ div = 63) > mmc_host mmc0: Bus speed (slot 0) = 200000000Hz (slot req 200000000Hz, > actual 200000000HZ div = 0) > mmc_host mmc0: Bus speed (slot 0) = 50000000Hz (slot req 52000000Hz, > actual 50000000HZ div = 0) > mmc_host mmc0: Bus speed (slot 0) = 400000000Hz (slot req 200000000Hz, > actual 200000000HZ div = 1) > smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0xC1E1 > > root@target:~# > root@target:~# time rtcwake -s10 -mmem[ 35.451572] vdd_ldo12: disabling > > rtcwake: wakeup from "mem" using /dev/rtc0 at Tue Feb 11 10:52:02 2020 > PM: suspend entry (deep) > Filesystems sync: 0.004 seconds > Freezing user space processes ... (elapsed 0.006 seconds) done. > OOM killer disabled. > Freezing remaining freezable tasks ... (elapsed 0.070 seconds) done. > hub 4-0:1.0: hub_ext_port_status failed (err = -32) > hub 3-0:1.0: hub_ext_port_status failed (err = -32) > 8<--- cut here --- > Unable to handle kernel NULL pointer dereference at virtual address 00000014 > pgd = 4c26b54b > [00000014] *pgd=00000000 > Internal error: Oops: 17 [#1] PREEMPT SMP ARM > Modules linked in: > CPU: 3 PID: 1468 Comm: kworker/u16:23 Not tainted > 5.6.0-rc1-next-20200211 #268 > Hardware name: Samsung Exynos (Flattened Device Tree) > Workqueue: events_unbound async_run_entry_fn > PC is at xhci_suspend+0x12c/0x520 > LR is at 0xa6aa9898 > pc : [<c0724c90>] lr : [<a6aa9898>] psr: 60000093 > sp : ec401df8 ip : 0000001a fp : c12e7864 > r10: 00000000 r9 : ecfb87b0 r8 : ecfb8220 > r7 : 00000000 r6 : 00000000 r5 : 00000004 r4 : ecfb81f0 > r3 : 00007d00 r2 : 00000001 r1 : 00000001 r0 : 00000000 > Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment none > Control: 10c5387d Table: 6bd4006a DAC: 00000051 > Process kworker/u16:23 (pid: 1468, stack limit = 0x6e4b6fba) > Stack: (0xec401df8 to 0xec402000) > ... > [<c0724c90>] (xhci_suspend) from [<c061b4f4>] (dpm_run_callback+0xb4/0x3fc) > [<c061b4f4>] (dpm_run_callback) from [<c061bd5c>] > (__device_suspend+0x134/0x7e8) > [<c061bd5c>] (__device_suspend) from [<c061c42c>] (async_suspend+0x1c/0x94) > [<c061c42c>] (async_suspend) from [<c0154bd0>] > (async_run_entry_fn+0x48/0x1b8) > [<c0154bd0>] (async_run_entry_fn) from [<c0149b38>] > (process_one_work+0x230/0x7bc) > [<c0149b38>] (process_one_work) from [<c014a108>] (worker_thread+0x44/0x524) > [<c014a108>] (worker_thread) from [<c01511fc>] (kthread+0x130/0x164) > [<c01511fc>] (kthread) from [<c01010b4>] (ret_from_fork+0x14/0x20) > Exception stack(0xec401fb0 to 0xec401ff8) > ... > ---[ end trace c72caf6487666442 ]--- > note: kworker/u16:23[1468] exited with preempt_count 1 > > Reverting it fixes the NULL pointer issue. I can provide more > information or do some other tests. Just let me know what will help to > fix it. > > > ... Ugh. Mathias, should I just revert this for now? thanks, greg k-h
