[PATCH v2 1/4] ARM: dts: exynos: Correct USB3503 GPIOs polarity

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Current USB3503 driver ignores GPIO polarity and always operates as if the
GPIO lines were flagged as ACTIVE_HIGH. Fix the polarity for the existing
USB3503 chip applications to match the chip specification and common
convention for naming the pins. The only pin, which has to be ACTIVE_LOW
is the reset pin. The remaining are ACTIVE_HIGH. This change allows later
to fix the USB3503 driver to properly use generic GPIO bindings and read
polarity from DT.

Signed-off-by: Marek Szyprowski <m.szyprowski@xxxxxxxxxxx>
---
 arch/arm/boot/dts/exynos4412-odroid-common.dtsi | 2 +-
 arch/arm/boot/dts/exynos5250-arndale.dts        | 2 +-
 arch/arm/boot/dts/exynos5410-odroidxu.dts       | 2 +-
 3 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
index ea55f377d17c..9c39e82e4ecb 100644
--- a/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
+++ b/arch/arm/boot/dts/exynos4412-odroid-common.dtsi
@@ -267,7 +267,7 @@
 
 		intn-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
 		connect-gpios = <&gpx3 4 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpx3 5 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
 		initial-mode = <1>;
 	};
 
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index d6c85efdb465..3eddf5dbcf7b 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -154,7 +154,7 @@
 		compatible = "smsc,usb3503a";
 
 		reset-gpios = <&gpx3 5 GPIO_ACTIVE_LOW>;
-		connect-gpios = <&gpd1 7 GPIO_ACTIVE_LOW>;
+		connect-gpios = <&gpd1 7 GPIO_ACTIVE_HIGH>;
 	};
 };
 
diff --git a/arch/arm/boot/dts/exynos5410-odroidxu.dts b/arch/arm/boot/dts/exynos5410-odroidxu.dts
index e0db251e253f..4f9297ae0763 100644
--- a/arch/arm/boot/dts/exynos5410-odroidxu.dts
+++ b/arch/arm/boot/dts/exynos5410-odroidxu.dts
@@ -170,7 +170,7 @@
 
 		intn-gpios = <&gpx0 7 GPIO_ACTIVE_HIGH>;
 		connect-gpios = <&gpx0 6 GPIO_ACTIVE_HIGH>;
-		reset-gpios = <&gpx1 4 GPIO_ACTIVE_HIGH>;
+		reset-gpios = <&gpx1 4 GPIO_ACTIVE_LOW>;
 		initial-mode = <1>;
 
 		clock-names = "refclk";
-- 
2.17.1




[Index of Archives]     [Linux SoC Development]     [Linux Rockchip Development]     [Linux for Synopsys ARC Processors]    
  • [Linux on Unisoc (RDA Micro) SoCs]     [Linux Actions SoC]     [Linux USB Development]     [Video for Linux]     [Linux Audio Users]     [Linux SCSI]     [Yosemite News]

  •   Powered by Linux