On 19. 4. 19. 오후 11:19, Lukasz Luba wrote:
> The patch adds description for DT binding for a new Exynos5422 Dynamic
> Memory Controller device.
>
> Signed-off-by: Lukasz Luba <l.luba@xxxxxxxxxxxxxxxxxxx>
> ---
> .../bindings/memory-controllers/exynos5422-dmc.txt | 73 ++++++++++++++++++++++
> 1 file changed, 73 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/memory-controllers/exynos5422-dmc.txt
>
> diff --git a/Documentation/devicetree/bindings/memory-controllers/exynos5422-dmc.txt b/Documentation/devicetree/bindings/memory-controllers/exynos5422-dmc.txt
> new file mode 100644
> index 0000000..133b3cc
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/memory-controllers/exynos5422-dmc.txt
> @@ -0,0 +1,73 @@
> +* Exynos5422 frequency and voltage scaling for Dynamic Memory Controller device
> +
> +The Samsung Exynos5422 SoC has DMC (Dynamic Memory Controller) to which the DRAM
> +memory chips are connected. The driver is to monitor the controller in runtime
> +and switch frequency and voltage. To monitor the usage of the controller in
> +runtime, the driver uses the PPMU (Platform Performance Monitoring Unit), which
> +is able to measure the current load of the memory.
> +When 'userspace' governor is used for the driver, an application is able to
> +switch the DMC and memory frequency.
> +
> +Required properties for DMC device for Exynos5422:
> +- compatible: Should be "samsung,exynos5422-bus".
As I already mentioned on many times, it is not fixed.
You have to fix it as following:
- exynos5422-bus -> exynos5422-dmc
> +- clock-names : the name of clock used by the bus, "bus".
The below examples doesn't contain the 'bus' clock name.
> +- clocks : phandles for clock specified in "clock-names" property.
> +- devfreq-events : phandles for PPMU devices connected to this DMC.
> +- vdd-supply : phandle for voltage regulator which is connected.
> +- reg : registers of two CDREX controllers, chip information, clocks subsystem.
> +- operating-points-v2 : phandle for OPPs described in v2 definition.
> +- device-handle : phandle of the connected DRAM memory device. For more
> + information please refer to Documentation
> +- devfreq-events : phandles of the PPMU events used by the controller.
> +
> +Example:
> +
> + ppmu_dmc0_0: ppmu@10d00000 {
> + compatible = "samsung,exynos-ppmu";
> + reg = <0x10d00000 0x2000>;
> + clocks = <&clock CLK_PCLK_PPMU_DREX0_0>;
> + clock-names = "ppmu";
> + status = "okay";
> + events {
> + ppmu_event_dmc0_0: ppmu-event3-dmc0_0 {
> + event-name = "ppmu-event3-dmc0_0";
> + };
> + };
> + };
> +
> + dmc: memory-controller@10c20000 {
> + compatible = "samsung,exynos5422-dmc";
> + reg = <0x10c20000 0x10000>, <0x10c30000 0x10000>,
> + <0x10000000 0x1000>, <0x10030000 0x1000>;
> + clocks = <&clock CLK_FOUT_SPLL>,
> + <&clock CLK_MOUT_SCLK_SPLL>,
> + <&clock CLK_FF_DOUT_SPLL2>,
> + <&clock CLK_FOUT_BPLL>,
> + <&clock CLK_MOUT_BPLL>,
> + <&clock CLK_SCLK_BPLL>,
> + <&clock CLK_MOUT_MX_MSPLL_CCORE>,
> + <&clock CLK_MOUT_MX_MSPLL_CCORE_PHY>,
> + <&clock CLK_MOUT_MCLK_CDREX>,
> + <&clock CLK_DOUT_CLK2X_PHY0>,
> + <&clock CLK_CLKM_PHY0>,
> + <&clock CLK_CLKM_PHY1>;
> + clock-names = "fout_spll",
> + "mout_sclk_spll",
> + "ff_dout_spll2",
> + "fout_bpll",
> + "mout_bpll",
> + "sclk_bpll",
> + "mout_mx_mspll_ccore",
> + "mout_mx_mspll_ccore_phy",
> + "mout_mclk_cdrex",
> + "dout_clk2x_phy0",
> + "clkm_phy0",
> + "clkm_phy1";
> + status = "okay";
> + operating-points-v2 = <&dmc_opp_table>;
> + devfreq-events = <&ppmu_event3_dmc0_0>, <&ppmu_event3_dmc0_1>,
> + <&ppmu_event3_dmc1_0>, <&ppmu_event3_dmc1_1>;
> + operating-points-v2 = <&dmc_opp_table>;
> + device-handle = <&samsung_K3QF2F20DB>;
> + vdd-supply = <&buck1_reg>;
> + };
>
--
Best Regards,
Chanwoo Choi
Samsung Electronics
