On Thursday, June 28, 2018 9:48:48 AM CEST Krzysztof Kozlowski wrote:
> On 28 June 2018 at 09:41, Krzysztof Kozlowski <krzk@xxxxxxxxxx> wrote:
> > On 27 June 2018 at 19:12, Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx> wrote:
> >> This DTS file have initial support Samsung Aries based phones.
> >> Initial version have support for:
> >> - sdcard
> >> - internal memory (present only on non 4g variant)
> >> - max8998 pmic and rtc
> >> - max17040 fuel gauge
> >> - gpio keys
> >> - fimd (no panel driver yet)
> >> - usb (peripherial mode)
> >> - wifi
> >>
> >> Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@xxxxxxxxx>
> >> ---
> >>
> >> Changes from v1:
> >> - Removed duplicated and unneeded headers
> >> - Corrected node names
> >> - Added missing spaces
> >> - Removed unneeded pinctrl and sorted entries
> >> - Set correct interrupt type for max8998 pmic
> >> - Add missing regulators
> >> ---
> >> ---
> >> arch/arm/boot/dts/s5pv210-aries.dtsi | 423 +++++++++++++++++++++++++++++++++++
> >> 1 file changed, 423 insertions(+)
> >> create mode 100644 arch/arm/boot/dts/s5pv210-aries.dtsi
> >>
> >> diff --git a/arch/arm/boot/dts/s5pv210-aries.dtsi b/arch/arm/boot/dts/s5pv210-aries.dtsi
> >> new file mode 100644
> >> index 000000000000..61b6cf76265f
> >> --- /dev/null
> >> +++ b/arch/arm/boot/dts/s5pv210-aries.dtsi
> >> @@ -0,0 +1,423 @@
> >> +// SPDX-License-Identifier: GPL-2.0
> >> +/*
> >> + * Samsung's S5PV210 based Galaxy Aries board device tree source
> >> + */
> >> +
> >> +/dts-v1/;
> >> +#include <dt-bindings/gpio/gpio.h>
> >> +#include <dt-bindings/interrupt-controller/irq.h>
> >> +#include "s5pv210.dtsi"
> >> +
> >> +/ {
> >> + compatible = "samsung,aries", "samsung,s5pv210";
> >> +
> >> + aliases {
> >> + i2c6 = &i2c_pmic;
> >> + i2c9 = &i2c_fuel;
> >> + };
> >> +
> >> + memory@30000000 {
> >> + device_type = "memory";
> >> + reg = <0x30000000 0x05000000
> >> + 0x40000000 0x10000000
> >> + 0x50000000 0x08000000>;
> >> + };
> >> +
> >> + wifi_pwrseq: wifi-pwrseq {
> >> + compatible = "mmc-pwrseq-simple";
> >> + reset-gpios = <&gpg1 2 GPIO_ACTIVE_LOW>;
> >> + pinctrl-names = "default";
> >> + pinctrl-0 = <&wlan_gpio_rst>;
> >> + post-power-on-delay-ms = <500>;
> >> + power-off-delay-us = <500>;
> >> + };
> >> +
> >> + i2c_pmic: i2c-gpio-0 {
> >> + compatible = "i2c-gpio";
> >> + sda-gpios = <&gpj4 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >> + scl-gpios = <&gpj4 3 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >> + i2c-gpio,delay-us = <2>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + pmic@66 {
> >> + compatible = "maxim,max8998";
> >> + reg = <0x66>;
> >> + interrupt-parent = <&gph0>;
> >> + interrupts = <7 IRQ_TYPE_EDGE_FALLING>;
> >> +
> >> + max8998,pmic-buck1-default-dvs-idx = <1>;
> >> + max8998,pmic-buck1-dvs-gpios = <&gph0 3 GPIO_ACTIVE_HIGH>,
> >> + <&gph0 4 GPIO_ACTIVE_HIGH>;
> >> + max8998,pmic-buck1-dvs-voltage = <1275000>, <1200000>,
> >> + <1050000>, <950000>;
> >> +
> >> + max8998,pmic-buck2-default-dvs-idx = <0>;
> >> + max8998,pmic-buck2-dvs-gpio = <&gph0 5 GPIO_ACTIVE_HIGH>;
> >> + max8998,pmic-buck2-dvs-voltage = <1100000>, <1000000>;
> >> +
> >> + regulators {
> >> + ldo2_reg: LDO2 {
> >> + regulator-name = "VALIVE_1.2V";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> + regulator-always-on;
> >> +
> >> + regulator-state-mem {
> >> + regulator-on-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo3_reg: LDO3 {
> >> + regulator-name = "VUSB_1.1V";
> >> + regulator-min-microvolt = <1100000>;
> >> + regulator-max-microvolt = <1100000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo4_reg: LDO4 {
> >> + regulator-name = "VADC_3.3V";
> >> + regulator-min-microvolt = <3300000>;
> >> + regulator-max-microvolt = <3300000>;
> >> + regulator-always-on;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo5_reg: LDO5 {
> >> + regulator-name = "VTF_2.8V";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <2800000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo6_reg: LDO6 {
> >> + regulator-name = "LDO6";
> >> + regulator-min-microvolt = <1600000>;
> >> + regulator-max-microvolt = <3600000>;
> >> + };
> >> +
> >> + ldo7_reg: LDO7 {
> >> + regulator-name = "VLCD_1.8V";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + /* Till we get panel driver */
> >> + regulator-always-on;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo8_reg: LDO8 {
> >> + regulator-name = "VUSB_3.3V";
> >> + regulator-min-microvolt = <3300000>;
> >> + regulator-max-microvolt = <3300000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo9_reg: LDO9 {
> >> + regulator-name = "VCC_2.8V_PDA";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <2800000>;
> >> + regulator-always-on;
> >> + };
> >> +
> >> + ldo10_reg: LDO10 {
> >> + regulator-name = "VPLL_1.2V";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> + regulator-always-on;
> >> +
> >> + regulator-state-mem {
> >> + regulator-on-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo11_reg: LDO11 {
> >> + regulator-name = "CAM_AF_3.0V";
> >> + regulator-min-microvolt = <3000000>;
> >> + regulator-max-microvolt = <3000000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo12_reg: LDO12 {
> >> + regulator-name = "CAM_SENSOR_CORE_1.2V";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo13_reg: LDO13 {
> >> + regulator-name = "VGA_VDDIO_2.8V";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <2800000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo14_reg: LDO14 {
> >> + regulator-name = "VGA_DVDD_1.8V";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo15_reg: LDO15 {
> >> + regulator-name = "CAM_ISP_HOST_2.8V";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <2800000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo16_reg: LDO16 {
> >> + regulator-name = "VGA_AVDD_2.8V";
> >> + regulator-min-microvolt = <2800000>;
> >> + regulator-max-microvolt = <2800000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ldo17_reg: LDO17 {
> >> + regulator-name = "VCC_3.0V_LCD";
> >> + regulator-min-microvolt = <3000000>;
> >> + regulator-max-microvolt = <3000000>;
> >> + /* Till we get panel driver */
> >> + regulator-always-on;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + buck1_reg: BUCK1 {
> >> + regulator-name = "vddarm";
> >> + regulator-min-microvolt = <750000>;
> >> + regulator-max-microvolt = <1500000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + regulator-suspend-microvolt = <1250000>;
> >> + };
> >> + };
> >> +
> >> + buck2_reg: BUCK2 {
> >> + regulator-name = "vddint";
> >> + regulator-min-microvolt = <750000>;
> >> + regulator-max-microvolt = <1500000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + regulator-suspend-microvolt = <1100000>;
> >> + };
> >> + };
> >> +
> >> + buck3_reg: BUCK3 {
> >> + regulator-name = "VCC_1.8V";
> >> + regulator-min-microvolt = <1800000>;
> >> + regulator-max-microvolt = <1800000>;
> >> + regulator-always-on;
> >> + };
> >> +
> >> + buck4_reg: BUCK4 {
> >> + regulator-name = "CAM_ISP_CORE_1.2V";
> >> + regulator-min-microvolt = <1200000>;
> >> + regulator-max-microvolt = <1200000>;
> >> +
> >> + regulator-state-mem {
> >> + regulator-off-in-suspend;
> >> + };
> >> + };
> >> +
> >> + ap32khz_reg: EN32KHz-AP {
> >> + regulator-name = "32KHz AP";
> >> + regulator-always-on;
> >> + };
> >> +
> >> + cp32khz_reg: EN32KHz-CP {
> >> + regulator-name = "32KHz CP";
> >> + };
> >> +
> >> + vichg_reg: ENVICHG {
> >> + regulator-name = "VICHG";
> >> + regulator-always-on;
> >> + };
> >> +
> >> + safe1_sreg: ESAFEOUT1 {
> >> + regulator-name = "SAFEOUT1";
> >> + };
> >> +
> >> + safe2_sreg: ESAFEOUT2 {
> >> + regulator-name = "SAFEOUT2";
> >> + };
> >> + };
> >> + };
> >> + };
> >> +
> >> + i2c_fuel: i2c-gpio-1 {
> >> + compatible = "i2c-gpio";
> >> + sda-gpios = <&mp05 1 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >> + scl-gpios = <&mp05 0 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
> >> + i2c-gpio,delay-us = <2>;
> >> + #address-cells = <1>;
> >> + #size-cells = <0>;
> >> +
> >> + fuelgauge@36 {
> >> + compatible = "maxim,max17040";
> >> + interrupt-parent = <&vic0>;
> >> + interrupts = <7>;
> >> + reg = <0x36>;
> >> + };
> >> + };
> >> +};
> >> +
> >> +&xusbxti {
> >> + clock-frequency = <24000000>;
> >> +};
> >> +
> >> +&pinctrl0 {
> >
> > Thanks for changes. You missed one part - ordering the labels here
> > alphabetically, so:
> >
> > &fimd {}
> > &hsotg {}
> > ...
> > &xusbxti {}
>
> Ah, now I see that you changed the order of nodes inside pinctrl. No
> need. These were good - ordered by pin names (so gpb, gpg, gph, gpj).
> I was referring only to the top-level overrides by label. The point is
> when people add new overrides, they tend to add them to the end... and
> this brings conflicts with multiple edits at the same time. When node
> overrides are ordered and new entries are being added, the chance of
> conflicts is reduced.
>
Ok now it's clear for me, will fix this (finally) in v3.
Thanks
> BR,
> Krzysztof
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
