Hi Maciej, Thank you for the patch. On Monday, 28 May 2018 12:47:11 EEST Maciej Purski wrote: > The patch adds bindings to Toshiba DSI/LVDS bridge TC358764. > Bindings describe power supplies, reset gpio and video interfaces. > > Signed-off-by: Andrzej Hajda <a.hajda@xxxxxxxxxxx> > Signed-off-by: Maciej Purski <m.purski@xxxxxxxxxxx> > --- > .../bindings/display/bridge/toshiba,tc358764.txt | 42 +++++++++++++++++++ > 1 file changed, 42 insertions(+) > create mode 100644 > Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > > diff --git > a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt new > file mode 100644 > index 0000000..d09bdc2 > --- /dev/null > +++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt > @@ -0,0 +1,42 @@ > +TC358764 MIPI-DSI to LVDS panel bridge > + > +Required properties: > + - compatible: "toshiba,tc358764" > + - reg: the virtual channel number of a DSI peripheral > + - vddc-supply: core voltage supply > + - vddio-supply: I/O voltage supply > + - vddmipi-supply: MIPI voltage supply > + - vddlvds133-supply: LVDS1 3.3V voltage supply > + - vddlvds112-supply: LVDS1 1.2V voltage supply That's a lot of power supplies. Could some of them be merged together ? See https://patchwork.freedesktop.org/patch/216058/ for an earlier discussion on the same subject. > + - reset-gpios: a GPIO spec for the reset pin > + > +The device node can contain zero to two 'port' child nodes, each with one > +child > +'endpoint' node, according to the bindings defined in [1]. > +The following are properties specific to those nodes. > + > +port: > + - reg: (required) can be 0 for DSI port or 1 for LVDS port; This seems pretty vague to me. It could be read as meaning that ports are completely optional, and that the port number you list can be used, but that something else could be used to. Let's make the port nodes mandatory. I propose the following. Required nodes: The TC358764 has DSI and LVDS ports whose connections are described using the OF graph bindings defined in Documentation/devicetree/bindings/graph.txt. The device node must contain one 'port' child node per DSI and LVDS port. The port nodes are numbered as follows. Port Number ------------------------------------------------------------------- DSI Input 0 LVDS Output 1 Each port node must contain endpoint nodes describing the hardware connections. > +[1]: Documentation/devicetree/bindings/media/video-interfaces.txt > + > +Example: > + > + bridge@0 { > + reg = <0>; > + compatible = "toshiba,tc358764"; > + vddc-supply = <&vcc_1v2_reg>; > + vddio-supply = <&vcc_1v8_reg>; > + vddmipi-supply = <&vcc_1v2_reg>; > + vddlvds133-supply = <&vcc_3v3_reg>; > + vddlvds112-supply = <&vcc_1v2_reg>; > + reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>; > + #address-cells = <1>; > + #size-cells = <0>; > + port@1 { > + reg = <1>; > + lvds_ep: endpoint { > + remote-endpoint = <&panel_ep>; > + }; > + }; > + }; -- Regards, Laurent Pinchart -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |