Hi Javier,
2015년 12월 03일 22:29에 Javier Martinez Canillas 이(가) 쓴 글:
> Hello Inki,
>
> On 12/03/2015 06:30 AM, Inki Dae wrote:
>> This patch updates a ports node binding for panel.
>>
>> With this, dp node can have a ports node which describes
>> a remote endpoint node that can be connected to panel or bridge
>> node.
>>
>> Signed-off-by: Inki Dae <inki.dae@xxxxxxxxxxx>
>> ---
>> .../bindings/display/exynos/exynos_dp.txt | 28 ++++++++++++++++++----
>> 1 file changed, 24 insertions(+), 4 deletions(-)
>>
>> diff --git a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> index 64693f2..15b52cb 100644
>> --- a/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> +++ b/Documentation/devicetree/bindings/display/exynos/exynos_dp.txt
>> @@ -66,8 +66,15 @@ Optional properties for dp-controller:
>> Hotplug detect GPIO.
>> Indicates which GPIO should be used for hotplug
>> detection
>> - -video interfaces: Device node can contain video interface port
>> - nodes according to [1].
>> +Video interfaces:
>> + Device node can contain video interface port nodes according to [1].
>> + The following are properties specific to those nodes:
>> +
>> + endpoint node connected to bridge or panel node:
>> + - remote-endpoint: specifies the endpoint in panel or bridge node.
>> + This node is required in all kinds of exynos dp
>> + to represent the connection between dp and bridge
>> + ,or dp and panel.
>>
>
> This is nice but I think the DT binding should also document that it uses
> a phandle to define the connection with the panel (but explain that is
> deprecated). If only so people looking at a DTS and then going to the DT
> binding can understand why there is two ways to define the same.
>
>> [1]: Documentation/devicetree/bindings/media/video-interfaces.txt
>>
>> @@ -111,9 +118,22 @@ Board Specific portion:
>> };
>>
>> ports {
>> - port@0 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> +
>
> These two properties are only needed when there is more than 2 ports and
> a reg property is used to number the port nodes but I don't think that's
> the case for Exynos DP and certainly is not the case in this example so
> I think you should just remove them.
Right. I found out that the dp can have only one port outbound. Will remove them.
>
>> + port {
>> dp_out: endpoint {
>> - remote-endpoint = <&bridge_in>;
>> + remote-endpoint = <&dp_in>;
>> + };
>> + };
>> + };
>> +
>> + panel@0 {
>> + reg = <0>;
>> + ...
>> + port {
>> + dp_in: endpoint {
>> + remote-endpoint = <&dp_out>;
>> };
>> };
>> };
>>
>
> The rest looks good to me so with the two changes feel free to add:
>
> Reviewed-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>
Thanks,
Inki Dae
>
> Best regards,
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
