Dear Myungjoo,
On 01/13/2015 05:42 PM, MyungJoo Ham wrote:
>>
>> This patch adds the generic exynos bus frequency driver for memory bus
>> with DEVFREQ framework. The Samsung Exynos SoCs have the common architecture
>> for memory bus between DRAM memory and MMC/sub IP in SoC. This driver can
>> support the memory bus frequency driver for Exynos SoCs.
>>
>> Each memory bus block has a clock for memory bus speed and frequency
>> table which is changed according to the utilization of memory bus on runtime.
>> And then each memory bus group has the one more memory bus blocks and
>> OPP table (including frequency and voltage), regulator, devfreq-event
>> devices.
>>
>> There are a little difference about the number of memory bus because each Exynos
>> SoC have the different sub-IP and different memory bus speed. In spite of this
>> difference among Exynos SoCs, we can support almost Exynos SoC by adding
>> unique data of memory bus to devicetree file.
>>
>> Cc: Myungjoo Ham <myungjoo.ham@xxxxxxxxxxx>
>> Cc: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
>> Cc: Kukjin Kim <kgene@xxxxxxxxxx>
>> Signed-off-by: Chanwoo Choi <cw00.choi@xxxxxxxxxxx>
>> ---
>> drivers/devfreq/Kconfig | 15 +
>> drivers/devfreq/Makefile | 1 +
>> drivers/devfreq/exynos-busfreq.c | 589 +++++++++++++++++++++++++++++++++++++++
>> 3 files changed, 605 insertions(+)
>> create mode 100644 drivers/devfreq/exynos-busfreq.c
>
> Exynos drivers are located at drivers/devfreq/exynos/
> Please relocate/rename exynos-busfreq.c
OK. I'll move it at drivers/devfreq/exynos directory.
Do you prefer 'exynos-bus.c' instead of 'exynos-busfreq.c'?
If you reply, I'll change it.
>
> []
>
>> diff --git a/drivers/devfreq/exynos-busfreq.c b/drivers/devfreq/exynos-busfreq.c
>> new file mode 100644
>> index 0000000..b180f43
>> --- /dev/null
>> +++ b/drivers/devfreq/exynos-busfreq.c
>
> []
>
>> +
>> +#define BUS_SATURATION_RATIO 40
>
> In order to be a common driver, this should be tunable.
>
> Because .dts is supposed to have hardware configuration only,
> you may keep a table of { chip-name, saturation ratio} in this
> driver and look up the saturation ratio based on the chip-name.
OK, I'll add new property for saturation_ratio.
I'll implement to use default saturation_ratio value ,
if dt node don't include saturation_ratio property.
>
>> +#define SAFEVOLT 50000
>> +
>> +struct exynos_memory_bus_opp_info {
>> + unsigned long rate;
>> + unsigned long volt;
>> +};
>> +
>> +struct exynos_memory_bus_block {
>> + struct clk *clk;
>> + struct exynos_memory_bus_opp_info *freq_table;
>> +};
>> +
>
> []
>
>> +#ifdef CONFIG_PM_SLEEP
>> +static int exynos_busfreq_resume(struct device *dev)
>> +{
>> + struct exynos_memory_bus_data *data = dev_get_drvdata(dev);
>> + int ret;
>> +
>> + ret = exynos_busfreq_enable_edev(data);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to enable the devfreq-event devices\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +
>> +static int exynos_busfreq_suspend(struct device *dev)
>> +{
>> + struct exynos_memory_bus_data *data = dev_get_drvdata(dev);
>> + int ret;
>> +
>> + ret = exynos_busfreq_disable_edev(data);
>> + if (ret < 0) {
>> + dev_err(dev, "failed to disable the devfreq-event devices\n");
>> + return ret;
>> + }
>> +
>> + return 0;
>> +}
>> +#endif
>
> Please disable regulator at suspend and resume it at resume.
>
> You may interfere with low-power mode of corresponding voltage line,
> which is often implemented to be activated if the regulator is
> explicitely disabled for "alive" regulators like this one.
OK, I'll modify it.
Thanks for your review.
Best Regards,
Chanwoo Choi
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
