Hi, On Thursday, October 02, 2014 09:45:41 AM Doug Anderson wrote: > Bartiomiej > > On Thu, Oct 2, 2014 at 9:39 AM, Bartlomiej Zolnierkiewicz > <b.zolnierkie@xxxxxxxxxxx> wrote: > > On Thursday, October 02, 2014 09:19:08 AM Doug Anderson wrote: > >> Bartiomiej, > >> > >> On Thu, Oct 2, 2014 at 9:10 AM, Bartlomiej Zolnierkiewicz > >> <b.zolnierkie@xxxxxxxxxxx> wrote: > >> > Regulators for MMC2 (SD card) are PVDD_TFLASH_2V8 (LDO19) for vmmc > >> > and PVDD_APIO_MMCOFF_2V8 (LDO13) for vqmmc. Currently the device > >> > tree entry for MMC2 uses PVDD_PRE_1V8 (LDO10) for vmmc and vqmmc is > >> > not specified. Fix it. > >> > > >> > Without this patch: > >> > - "mmc: dw_mmc: use mmc_regulator_get_supply to handle regulators" > >> > patch causes a SD card detection to fail > >> > - "mmc: dw_mmc: Support voltage changes" patch causes a boot hang > >> > > >> > This patch fixes both above problems. > >> > > >> > Suggested-by: Doug Anderson <dianders@xxxxxxxxxx> > >> > Cc: Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxxxx> > >> > Cc: Ulf Hansson <ulf.hansson@xxxxxxxxxx> > >> > Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@xxxxxxxxxxx> > >> > Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx> > >> > --- > >> > arch/arm/boot/dts/exynos5420-arndale-octa.dts | 3 ++- > >> > 1 file changed, 2 insertions(+), 1 deletion(-) > >> > > >> > Index: b/arch/arm/boot/dts/exynos5420-arndale-octa.dts > >> > =================================================================== > >> > --- a/arch/arm/boot/dts/exynos5420-arndale-octa.dts 2014-10-02 15:44:53.014826886 +0200 > >> > +++ b/arch/arm/boot/dts/exynos5420-arndale-octa.dts 2014-10-02 17:35:24.110600398 +0200 > >> > @@ -74,7 +74,8 @@ > >> > samsung,dw-mshc-ddr-timing = <1 2>; > >> > pinctrl-names = "default"; > >> > pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>; > >> > - vmmc-supply = <&ldo10_reg>; > >> > + vmmc-supply = <&ldo19_reg>; > >> > + vqmmc-supply = <&ldo13_reg>; > >> > >> This looks right to me. ...but I notice that ldo13 and ldo19 are not > >> "always-on" in the DTS. Are you sure card detect works for you if you > >> eject your card and try to put it back in? > >> > >> ...eventually the "always-on" won't be needed, but for now I think it is... > > > > Card detection works fine without "always-on". > > That's weird. > > 1. In the schematics I see XMMC2CDN has an external pullup to PVDD_TFLASH_2V8. > > 2. The internal pullup should (I think) be to VDDQ_MMC2 which is > PVDD_APIO_MMCOFF_2V8. > > 3. In (51da224 mmc: dw_mmc: use mmc_regulator_get_supply to handle > regulators) we should be turning off both regulators in > "MMC_POWER_OFF". > > 4. If I understand correctly MMC_POWER_OFF is called when the card is > ejected, which means that both regulators should be off when the card > is ejected. > > 5. I don't think card detect can work if neither regulator is powered. > > > One of the above points must be wrong. Any idea which one? Can you > check to see if MMC_POWER_OFF is called for you when the card is > ejected? Can you check to see if these regulators are off? MMC_POWER_OFF is called on card removal and both regulators get disabled (I have verified that they are really off with regulator_is_enabled() which returns 1 before and 0 after disabling regulator). It seems that 5. is wrong? Best regards, -- Bartlomiej Zolnierkiewicz Samsung R&D Institute Poland Samsung Electronics -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |