Hello Wolfram,
On 09/11/2014 01:08 PM, Wolfram Sang wrote:
>
> Funny timing. I am just reviewing the series from Lee and also stumbled
> over modaliases, too...
>
> On Thu, Sep 11, 2014 at 10:19:54AM +0100, Nick Dyer wrote:
>> On 11/09/14 09:38, Javier Martinez Canillas wrote:
>> > To expand on what Sjoerd already said and just to be sure everyone is on the
>> > same page.
>> >
>> > The problem is that right now the driver reports the following modalias:
>> >
>> > # cat /sys/class/i2c-adapter/i2c-8/8-004b/modalias
>> > i2c:maxtouch
>> >
>> > but if you look at the module information, that is not a valid alias:
>> >
>> > # modinfo atmel_mxt_ts | grep alias
>> > alias: i2c:mXT224
>> > alias: i2c:atmel_mxt_tp
>> > alias: i2c:atmel_mxt_ts
>> > alias: i2c:qt602240_ts
>> > alias: of:N*T*Catmel,maxtouch*
>> >
>> > which means that udev/kmod can't load the module automatically based on the
>> > alias information.
>> >
>> > The aliases are filled by both MODULE_DEVICE_TABLE(i2c, mxt_id) and
>> > MODULE_DEVICE_TABLE(of, mxt_of_match) so after Sjoerd's patch:
>> >
>> > # cat /sys/class/i2c-adapter/i2c-8/8-004b/modalias
>> > i2c:maxtouch
>> >
>> > # modinfo atmel_mxt_ts | grep alias
>> > alias: i2c:mXT224
>> > alias: i2c:maxtouch
>> > alias: i2c:atmel_mxt_tp
>> > alias: i2c:atmel_mxt_ts
>> > alias: i2c:qt602240_ts
>> >
>> > which matches the reported uevent so the module will be auto-loaded.
>> >
>> > This is because the I2C subsystem hardcodes i2c:<client->name>, if you look at
>> > drivers/i2c/i2c-core.c:
>> >
>> > /* uevent helps with hotplug: modprobe -q $(MODALIAS) */
>> > static int i2c_device_uevent(struct device *dev, struct kobj_uevent_env *env)
>> > {
>> > ...
>> > if (add_uevent_var(env, "MODALIAS=%s%s",
>> > I2C_MODULE_PREFIX, client->name))
>> > ...
>> > }
>> >
>> > I've looked at Lee's series and AFAICT that remains the same so I second
>> > Sjoerd that module auto-loading will continue to be broken.
>
> I think the above code in the i2c core needs a fix. Will have a closer
> look after lunch.
>
Agreed, I just posted an RFC patch [0] with the fix but as Sjoerd pointed out
on an internal review, changing that will regress all the drivers that were
relying on the old behavior.
>> The i2c aliases are a bit confusing. The original device the driver was
>> written for was called qt602240, which was renamed by Atmel to mXT224 when
>> the chip series was called "maXTouch". The driver now actually supports
>> many other chips which aren't listed (more than 20 devices that I've
>> personally tested). I could add them all, but it would be an extremely long
>> list. It may be preferable to use the generic name maXTouch.
>
> This is probably true for some more I2C devices. Like RTCs being
> compatible or, most prominent, EEPROMS. I don't want to have a list of
> all vendors producing 24c02s if they are all compatible. If generic
> entries are frowned upon, I'd agree on a "first come, first served" policy:
> Somebody provides one compatible-property with the vendor which happens
> to be on that board, and the others have to reuse that
> compatible-property since they are, well, compatible.
>
Agreed.
>> So I think the sensible thing to do here would be to add "maxtouch" to the
>> i2c list to fix the module autoload issue.
>
> This is a workaround. It would make sense, however, to add it because we
> want to support i2c_board_info structures.
>
I think it really depends if an IP block can be used on non-DT platforms
(which I think is true for this trackpad) but if a driver is for an IP block
that can only be used on a DT-only platform (e.g: a PMIC that is controlled
over I2C and is only compatible with a DT-only SoC) then I don't think we need
to support the i2c_board_info structure and can get rid of the I2C ID table on
these drivers once Lee series land.
> Regards,
>
> Wolfram
>
Best regards,
Javier
[0]: https://patchwork.ozlabs.org/patch/388200/
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
