On Thu, Aug 28, 2014 at 10:03 AM, Mark Rutland <mark.rutland@xxxxxxx> wrote:
> On Thu, Aug 28, 2014 at 05:28:22PM +0100, Olof Johansson wrote:
>> On Thu, Aug 28, 2014 at 2:48 AM, Mark Rutland <mark.rutland@xxxxxxx> wrote:
>> > Hi,
>> >
>> >> > + cpus {
>> >> > + #address-cells = <2>;
>> >> > + #size-cells = <0>;
>> >>
>> >> Why size-cells=2? Can you not fit a cpuid in 32 bits?
>> >
>> > As of commit 72aea393a2e7 (arm64: smp: honour #address-size when parsing
>> > CPU reg property) Linux can handle single-cell cpu node reg entries
>> > where /cpus/#address-cells = <1>.
>> >
>> > I can't make any guarantees about other code (e.g. bootloaders) which
>> > might try to do things with cpu nodes, YMMV.
>>
>> Ok. If address-cells is kept at 2 the unit address needs to be changed
>> to "0,0". So one or the other has to be changed.
>
> I'm happy either way.
>
> I'm not sure the rest of the tree had "0," prefixes on all of the
> unit-addresses for 64-bit addresses that were under 4GB, and I'm not
> sure that existing dts consistently do that either.
>
> Do we want to enforce that for all 64-bit unit-addresses?
Yeah, I believe that's the only valid format for a 2-address-cell unit address.
>> > [...]
>> >
>> >> > + hsi2c_2: hsi2c@14E60000 {
>> >>
>> >> I much prefer lowercase hex in unit addresses (and reg entries) below. I
>> >> know 32-bit uses uppercase, but let's switch going forward here.
>> >
>> > My preference also; I'm happy to enforce that on new dts.
>> >
>> > [...]
>> >
>> >> > + timer {
>> >> > + compatible = "arm,armv8-timer";
>> >> > + interrupts = <1 13 0xff01>,
>> >> > + <1 14 0xff01>,
>> >> > + <1 11 0xff01>,
>> >> > + <1 10 0xff01>;
>> >> > + clock-frequency = <24000000>;
>> >> > + use-clocksource-only;
>> >> > + use-physical-timer;
>> >>
>> >> These two properties are not standard, and I would expect any 64-bit
>> >> platform to come with PSCI such that you have a way to initialize the
>> >> virtual timers.
>> >
>> > Likewise with clock-frequency. It's not a full workaround, and it's not
>> > hard to initialise CNTFRQ on each CPU.
>>
>> Technically clock-frequency is documented, but not recommended to be
>> used unless needed for working around firmware that doesn't setup the
>> register value. :)
>
> True.
>
>> In this case it's likely a cargo cult carry over from 5250 where the
>> CNTFRQ requirement happened around the same time as we were working on
>> it so that generation firmware lacked support for it -- it should
>> since then have been fixed properly.
>
> It's probably unhelpful that the documentation isn't explicit about
> that. On that front, how about the patch below?
>
> Mark.
>
> ---->8----
> From 67104ad5a56e4c18f9c41f06af028b7561740afd Mon Sep 17 00:00:00 2001
> From: Mark Rutland <mark.rutland@xxxxxxx>
> Date: Thu, 28 Aug 2014 17:41:03 +0100
> Subject: [PATCH] Doc: dt: arch_timer: discourage clock-frequency use
>
> The ARM Generic Timer (AKA the architected timer, arm_arch_timer)
> features a CPU register (CNTFRQ) which firmware is intended to
> initialize, and non-secure software can read to determine the frequency
> of the timer. On CPUs with secure state, this register cannot be written
> from non-secure states.
>
> The firmware of early SoCs featuring the timer did not correctly
> initialize CNTFRQ correctly on all CPUs, requiring the frequency to be
> described in DT as a workaround. This workaround is not complete however
> as CNTFRQ is exposed to all software in a privileged non-secure mode,
> including KVM guests. The firmware and DTs for recent SoCs have followed
> the example set by these early SoCs.
>
> This patch updates the arch timer binding documentation to make it
> clearer that the use of the clock-frequency property is a poor
> work-around. The MMIO generic timer binding is similarly updated, though
> this is less of a concern as there is generally no need to expose the
> MMIO timers to guest OSs.
>
> Signed-off-by: Mark Rutland <mark.rutland@xxxxxxx>
> Cc: Marc Zyngier <marc.zyngier@xxxxxxx>
With caps fixed:
Acked-by: Olof Johansson <olof@xxxxxxxxx>
> ---
> Documentation/devicetree/bindings/arm/arch_timer.txt | 8 ++++++--
> 1 file changed, 6 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/arm/arch_timer.txt b/Documentation/devicetree/bindings/arm/arch_timer.txt
> index 37b2caf..5ca3f95 100644
> --- a/Documentation/devicetree/bindings/arm/arch_timer.txt
> +++ b/Documentation/devicetree/bindings/arm/arch_timer.txt
> @@ -17,7 +17,10 @@ to deliver its interrupts via SPIs.
> - interrupts : Interrupt list for secure, non-secure, virtual and
> hypervisor timers, in that order.
>
> -- clock-frequency : The frequency of the main counter, in Hz. Optional.
> +- clock-frequency : The frequency of the main counter, in Hz. Should be present
> + only where necessary to work around BROKEN firmware which does not configure
No need to do broken in all caps. In reality I don't expect it to make
a difference on people complying or not. :)
> + CNTFRQ on all CPUs to a uniform correct value. Use of this property is
> + STRONGLY DISCOURAGED; fix your firmware unless absolutely impossible.
Same here.
>
> - always-on : a boolean property. If present, the timer is powered through an
> always-on power domain, therefore it never loses context.
> @@ -38,7 +41,8 @@ Example:
>
> - compatible : Should at least contain "arm,armv7-timer-mem".
>
> -- clock-frequency : The frequency of the main counter, in Hz. Optional.
> +- clock-frequency : The frequency of the main counter, in Hz. Should be present
> + only when firmware has not configured the MMIO CNTFRQ registers.
>
> - reg : The control frame base address.
>
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
