On Thu, Aug 28, 2014 at 06:34:33AM +0100, Ajay kumar wrote:
> On Wed, Aug 27, 2014 at 8:31 PM, Mark Rutland <mark.rutland@xxxxxxx> wrote:
> > On Wed, Aug 27, 2014 at 03:48:27PM +0100, Ajay Kumar wrote:
> >> Add DT nodes for ptn3460 bridge chip and panel.
> >> Add backlight enable pin and backlight power supply for pwm-backlight.
> >> Also add bridge phandle needed by dp to enable display on snow.
> >>
> >> Note that, snow doesn't support "chunghwa,claa101wb01" panel,
> >> but still we choose to reuse the binding since "chunghwa,claa101wb01"
> >> has similar LCD timings.
> >
> > What does it actually have?
> >
> > It's fine to have "chunghwa,claa101wb01" as a fallback but we should
> > have an identifier for the actual display, too.
> Actual display used is "AUO,B116XTN0", for which no data currently exists
> in panel file. Instead of adding a new panel_desc for B116XTN0,
> why not we reuse existing ones? what is the "identifier" you are talking about?
The compatible string.
So in the dts we'd have compatible = "au0,b116xtn0", "chunghwa,claa101wb01";
That way if we need specific data we can add it later.
What vendor is AU0? Can we add a vendor-prefix in parallel?
Thanks,
Mark.
>
> Ajay
> > Thanks,
> > Mark.
> >
> >> Signed-off-by: Ajay Kumar <ajaykumar.rs@xxxxxxxxxxx>
> >> ---
> >> Changes since V1:
> >> -- Remove "simple-panel" compatible string.
> >> -- Use GPIO_ACTIVE_HIGH instead of 0.
> >> -- Change panel node naming from "panel-simple" to "panel".
> >>
> >> arch/arm/boot/dts/exynos5250-snow.dts | 41 ++++++++++++++++++---------------
> >> 1 file changed, 22 insertions(+), 19 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/exynos5250-snow.dts b/arch/arm/boot/dts/exynos5250-snow.dts
> >> index f2b8c41..1ac9709 100644
> >> --- a/arch/arm/boot/dts/exynos5250-snow.dts
> >> +++ b/arch/arm/boot/dts/exynos5250-snow.dts
> >> @@ -9,6 +9,7 @@
> >> */
> >>
> >> /dts-v1/;
> >> +#include <dt-bindings/gpio/gpio.h>
> >> #include "exynos5250.dtsi"
> >> #include "exynos5250-cros-common.dtsi"
> >>
> >> @@ -181,7 +182,7 @@
> >> dcdc3 {
> >> ti,enable-ext-control;
> >> };
> >> - fet1 {
> >> + fet1: fet1 {
> >> regulator-name = "vcd_led";
> >> ti,overcurrent-wait = <3>;
> >> };
> >> @@ -204,7 +205,7 @@
> >> regulator-always-on;
> >> ti,overcurrent-wait = <3>;
> >> };
> >> - fet6 {
> >> + fet6: fet6 {
> >> regulator-name = "lcd_vdd";
> >> ti,overcurrent-wait = <3>;
> >> };
> >> @@ -253,6 +254,15 @@
> >> pinctrl-0 = <&max98095_en>;
> >> pinctrl-names = "default";
> >> };
> >> +
> >> + ptn3460: lvds-bridge@20 {
> >> + compatible = "nxp,ptn3460";
> >> + reg = <0x20>;
> >> + powerdown-gpios = <&gpy2 5 GPIO_ACTIVE_HIGH>;
> >> + reset-gpios = <&gpx1 5 GPIO_ACTIVE_HIGH>;
> >> + edid-emulation = <5>;
> >> + panel = <&panel>;
> >> + };
> >> };
> >>
> >> i2s0: i2s@03830000 {
> >> @@ -300,11 +310,13 @@
> >> vdd_pll-supply = <&ldo8_reg>;
> >> };
> >>
> >> - backlight {
> >> + backlight: backlight {
> >> compatible = "pwm-backlight";
> >> pwms = <&pwm 0 1000000 0>;
> >> brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
> >> default-brightness-level = <7>;
> >> + enable-gpios = <&gpx3 0 GPIO_ACTIVE_HIGH>;
> >> + power-supply = <&fet1>;
> >> pinctrl-0 = <&pwm0_out>;
> >> pinctrl-names = "default";
> >> };
> >> @@ -314,6 +326,12 @@
> >> samsung,invert-vclk;
> >> };
> >>
> >> + panel: panel {
> >> + compatible = "chunghwa,claa101wb01";
> >> + power-supply = <&fet6>;
> >> + backlight = <&backlight>;
> >> + };
> >> +
> >> dp-controller@145B0000 {
> >> status = "okay";
> >> pinctrl-names = "default";
> >> @@ -325,22 +343,7 @@
> >> samsung,link-rate = <0x0a>;
> >> samsung,lane-count = <2>;
> >> samsung,hpd-gpio = <&gpx0 7 0>;
> >> -
> >> - display-timings {
> >> - native-mode = <&timing1>;
> >> -
> >> - timing1: timing@1 {
> >> - clock-frequency = <70589280>;
> >> - hactive = <1366>;
> >> - vactive = <768>;
> >> - hfront-porch = <40>;
> >> - hback-porch = <40>;
> >> - hsync-len = <32>;
> >> - vback-porch = <10>;
> >> - vfront-porch = <12>;
> >> - vsync-len = <6>;
> >> - };
> >> - };
> >> + bridge = <&ptn3460>;
> >> };
> >> };
> >>
> >> --
> >> 1.7.9.5
> >>
> >> --
> >> To unsubscribe from this list: send the line "unsubscribe devicetree" in
> >> the body of a message to majordomo@xxxxxxxxxxxxxxx
> >> More majordomo info at http://vger.kernel.org/majordomo-info.html
> >>
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
