On 08/28/2014 12:49 AM, Doug Anderson wrote:
> Jaehoon,
>
> On Tue, Aug 26, 2014 at 9:47 PM, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
>> Doug,
>>
>> On 08/27/2014 01:14 PM, Doug Anderson wrote:
>>> Jaehoon,
>>>
>>> On Tue, Aug 26, 2014 at 8:48 PM, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
>>>> Hi, Doug,
>>>>
>>>> On 08/26/2014 12:25 AM, Doug Anderson wrote:
>>>>> Jaehoon,
>>>>>
>>>>> On Mon, Aug 25, 2014 at 1:50 AM, Jaehoon Chung <jh80.chung@xxxxxxxxxxx> wrote:
>>>>>> On 08/25/2014 05:13 PM, Ulf Hansson wrote:
>>>>>>> On 22 August 2014 20:27, Sonny Rao <sonnyrao@xxxxxxxxxxxx> wrote:
>>>>>>>> On Fri, Aug 22, 2014 at 8:31 AM, Ulf Hansson <ulf.hansson@xxxxxxxxxx> wrote:
>>>>>>>>> On 22 August 2014 15:47, Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxx> wrote:
>>>>>>>>>> Exynos 5250 and 5420 based boards uses built-in CD# line for card
>>>>>>>>>> detection.But unfortunately CD# line is on the same voltage rails
>>>>>>>>>> as of I/O voltage rails. When we cut off vqmmc,the consequent card
>>>>>>>>>> detection will break in these boards.
>>>>>>
>>>>>> I didn't know that use CD# line for card detect.
>>>>>> And if CD# voltage rails and I/O voltage rail are same voltage, it doesn't make sense.
>>>>>> Which card is used with same voltages? (eMMC? SD? SDIO?)
>>>>>>
>>>>>> Well, I have checked Exynos5250 and 5420, but it looks like not same rails.
>>>>>
>>>>> I'm not sure I totally understood what you said. In my manual I have
>>>>> a table titled "Table 2-1 Exynos 5420 Pin List". Look in this table
>>>>> for XMMC2CDN and XMMC2DATA_0. Look to the right of the table and
>>>>> you'll see the power domain. For both it shows VDDQ_MMC2. If that
>>>>> doesn't mean that the two are in the same voltage domain then I don't
>>>>> know what does. Can you point to any examples where they have
>>>>> different voltage domains?
>>>> I think you're mis-understanding for it.
>>>> Right, It's described at exynos5420, but it's not connected.
>>>
>>> "It's not connected". What do you mean? If I were to guess I'd say
>>> that on some particular board you're looking at they don't happen to
>>> use the "CD" pin for card detect. If this is what you mean, it
>>> doesn't help me. exynos5420-peach-pit does use the CD pin for card
>>> detect. You can look at the DTS file and confirm it.
>>
>> I didn't know how exynos5420-peach-pit's circuit is configured.
>> But i guess that almost all exynos5 boards are configured with the similar circuit.
>>
>> At Almost all Exynos5 board, CD-pin is used, but not included in Same power domain.
>> (CD-pin is external card-detect pin. - like XEINT_# pin)
>> You mentioned CD# and DATA# lines is used the same power domain, right?
>> In Circuit (not exynos5420-peach-pit), DATA# line and CMD/CLK(vqmmc) is same power supply, and vdd is used other power supply.
>> Not use the CD# pin, used the XEINT_# pin.
>> So i think we don't need to consider the CD#.
>> If exynos5420-peach-pit board is used the CD#-pin, then our discussion can be changed.
>
> Maybe on your board you have CD connected to a "gpx" line. ...but not
> mine. The guys who designed our hardware followed the SMDK5420
> reference schematics which connect the SD card slot card detect to
> "gpc2_2", which is the card detect pin.
>
> See "arch/arm/boot/dts/exynos5420-smdk5420.dts", specifically noting
> the lack of a GPIO card detect and the inclusion of "sd2_cd"
>
> mmc@12220000 {
> status = "okay";
> card-detect-delay = <200>;
> samsung,dw-mshc-ciu-div = <3>;
> samsung,dw-mshc-sdr-timing = <2 3>;
> samsung,dw-mshc-ddr-timing = <1 2>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> bus-width = <4>;
> cap-sd-highspeed;
> };
>
> See "arch/arm/boot/dts/exynos5420-peach-pit.dts" too:
>
> &mmc_2 {
> status = "okay";
> num-slots = <1>;
> cap-sd-highspeed;
> card-detect-delay = <200>;
> clock-frequency = <400000000>;
> samsung,dw-mshc-ciu-div = <3>;
> samsung,dw-mshc-sdr-timing = <2 3>;
> samsung,dw-mshc-ddr-timing = <1 2>;
> pinctrl-names = "default";
> pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
> bus-width = <4>;
> };
>
>
> Here, see this ASCII art that shows how some lines are hooked up on
> peach-pit. You might need to paste this into something with a
> fixed-width font.
>
> +--------------------
> | Exynos 5420
> |
> |
> P2.8V_LOUT4 ---------|- VDDQ_MMC2 (AK7)
> | |
> | |
> +-+- 10K res -+----|- XMMC2CDN (AK6)
> | | |
> | | |
> | | |
> | Ext CD |
> | |
> +-- 10K res-+--+---|- XMMC2CMD (AK8)
> |
> |
> Ext CMD
>
> You can see from the above that the external card detect signal (that
> goes to the connector) named "Ext CD" is pulled up to the same voltage
> as the external CMD signal (that also goes to the connector). This is
> vqmmc. If we turn off vqmmc then the 10K resistor will (I think) act
> as a pull down, or in the best case it will be floating.
>
> Said another way: we can't read card detect when vqmmc is off.
If that's the case, it makes sense. But i wonder why designed like that.
Anyway, then we need to consider that controls the vqmmc power for card-detection.
But if polling system uses, it seems to detect the card.
Polling is the method that sends the status command.
At that time, we can notice whether card is insert/remove. Is it impossible?
>
>> Your commit message looks like all exynos5250/5420 board are used CD# line.
>
> The commit message should be clearer, agreed. I think I asked Yuvaraj
> to make sure that the code only invoked this quirk on exynos and only
> if a GPIO was not used for card detect. Yuvaraj: can you make it more
> obvious that not all exynos5250/5420 boards need this, only those that
> use the "official" card detect line?
>
>
>>> ...or are you saying that the CD pin somehow changes voltage domains
>>> when configured as a GPIO? I find that very hard to believe. What
>>> voltage domain does it go to? If it goes to a 1.8V voltage domain
>>> then that would be bad when vqmmc was 3.3V. If it goes to a 3.3V
>>> voltage domain then that would be bad when vqmmc was 1.8V. Remember
>>> that externally we've got a pull up to vqmmc.
>>
>> It is used with XEINT_# pin instead of CD# pin.
>> As i mentioned above, if exynos5420-peach-pit is used CD# line and not used XEINT_# pin,
>> my point is meaningless. :)
>>
>> Is exynos5420-peach-pit board used with CD#pin, not XEINT_# pin?
>
> Yes. It is using CD#. Do you remove your objections to this patch,
> then (once the commit message is clearer)?
Sure.
And I will also effort to find it, if we can find the more generic approach.
Best Regards,
Jaehoon Chung
>
> -Doug
> --
> To unsubscribe from this list: send the line "unsubscribe linux-mmc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
