Exynos 5250 and 5420 based boards uses built-in CD# line for card
detection.But unfortunately CD# line is on the same voltage rails
as of I/O voltage rails. When we cut off vqmmc,the consequent card
detection will break in these boards.
These hosts (obviously) need to keep vqmmc (and thus vmmc) on all the
time, even when the mmc core tells them to power off. However, one
problem is that these cards won't properly handle mmc_power_cycle().
That's needed to handle error cases when trying to switch voltages
(see 0797e5f mmc:core: Fixup signal voltage switch).
This patch adds a new MMC_POWER_OFF_HARD mode when it's doing a power
cycle. This mode differs from the normal MMC_POWER_OFF mode in that
the mmc core will promise to power the slot back on before it expects
the host to detect card insertion or removal.
Also if we let alone the vqmmc turned on when vmmc turned off, the
card could have half way powered and this can damage the card. So
this patch adds a check so that, if the board used the built-in
card detection mechanism i.e through CDETECT, it will not turned
down vqmmc and vmmc both.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@xxxxxxxxxxx>
Signed-off-by: Doug Anderson <dianders@xxxxxxxxxxxx>
---
changes from v1:
1.added a new MMC_POWER_OFF_HARD mode as per Doug Anderson's suggestion.
2.added dw_mci_exynos_post_init() to perform the host specific post
initialisation.
3.added a new flag MMC_CAP2_CD_NEEDS_POWER for host->caps2.
drivers/mmc/core/core.c | 16 ++++++++++++++--
drivers/mmc/core/debugfs.c | 3 +++
drivers/mmc/host/dw_mmc-exynos.c | 12 ++++++++++++
drivers/mmc/host/dw_mmc.c | 25 +++++++++++++++++++++++++
drivers/mmc/host/dw_mmc.h | 2 ++
include/linux/mmc/host.h | 2 ++
6 files changed, 58 insertions(+), 2 deletions(-)
diff --git a/drivers/mmc/core/core.c b/drivers/mmc/core/core.c
index 68f5f4b..79ced36 100644
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
@@ -1564,9 +1564,9 @@ void mmc_power_up(struct mmc_host *host, u32 ocr)
mmc_host_clk_release(host);
}
-void mmc_power_off(struct mmc_host *host)
+void _mmc_power_off(struct mmc_host *host, unsigned char power_mode)
{
- if (host->ios.power_mode == MMC_POWER_OFF)
+ if (host->ios.power_mode == power_mode)
return;
mmc_host_clk_hold(host);
@@ -1579,6 +1579,7 @@ void mmc_power_off(struct mmc_host *host)
host->ios.chip_select = MMC_CS_DONTCARE;
}
host->ios.power_mode = MMC_POWER_OFF;
+ host->ios.power_mode = power_mode;
host->ios.bus_width = MMC_BUS_WIDTH_1;
host->ios.timing = MMC_TIMING_LEGACY;
mmc_set_ios(host);
@@ -1593,9 +1594,20 @@ void mmc_power_off(struct mmc_host *host)
mmc_host_clk_release(host);
}
+void mmc_power_off(struct mmc_host *host)
+{
+ _mmc_power_off(host, MMC_POWER_OFF);
+}
+
void mmc_power_cycle(struct mmc_host *host, u32 ocr)
{
mmc_power_off(host);
+ /* If host normally ignores MMC_POWER_OFF, tell it to pay attention */
+ if (host->caps2 & MMC_CAP2_CD_NEEDS_POWER)
+ _mmc_power_off(host, MMC_POWER_OFF_HARD);
+ else
+ _mmc_power_off(host, MMC_POWER_OFF);
+
/* Wait at least 1 ms according to SD spec */
mmc_delay(1);
mmc_power_up(host, ocr);
diff --git a/drivers/mmc/core/debugfs.c b/drivers/mmc/core/debugfs.c
index 91eb162..3d9c5a3 100644
--- a/drivers/mmc/core/debugfs.c
+++ b/drivers/mmc/core/debugfs.c
@@ -108,6 +108,9 @@ static int mmc_ios_show(struct seq_file *s, void *data)
case MMC_POWER_ON:
str = "on";
break;
+ case MMC_POWER_OFF_HARD:
+ str = "hard off";
+ break;
default:
str = "invalid";
break;
diff --git a/drivers/mmc/host/dw_mmc-exynos.c b/drivers/mmc/host/dw_mmc-exynos.c
index 0fbc53a..4e26049 100644
--- a/drivers/mmc/host/dw_mmc-exynos.c
+++ b/drivers/mmc/host/dw_mmc-exynos.c
@@ -17,6 +17,7 @@
#include <linux/mmc/mmc.h>
#include <linux/of.h>
#include <linux/of_gpio.h>
+#include <linux/mmc/slot-gpio.h>
#include <linux/slab.h>
#include "dw_mmc.h"
@@ -217,6 +218,16 @@ static void dw_mci_exynos_set_ios(struct dw_mci *host, struct mmc_ios *ios)
}
}
+static void dw_mci_exynos_post_init(struct dw_mci_slot *slot)
+{
+ struct dw_mci_board *brd = slot->host->pdata;
+ struct mmc_host *mmc = slot->mmc;
+
+ if (!(brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION) &&
+ IS_ERR_VALUE(mmc_gpio_get_cd(mmc)))
+ mmc->caps2 |= MMC_CAP2_CD_NEEDS_POWER;
+}
+
static int dw_mci_exynos_parse_dt(struct dw_mci *host)
{
struct dw_mci_exynos_priv_data *priv;
@@ -399,6 +410,7 @@ static const struct dw_mci_drv_data exynos_drv_data = {
.prepare_command = dw_mci_exynos_prepare_command,
.set_ios = dw_mci_exynos_set_ios,
.parse_dt = dw_mci_exynos_parse_dt,
+ .post_init = dw_mci_exynos_post_init,
.execute_tuning = dw_mci_exynos_execute_tuning,
};
diff --git a/drivers/mmc/host/dw_mmc.c b/drivers/mmc/host/dw_mmc.c
index f20b4b8..6f2c681 100644
--- a/drivers/mmc/host/dw_mmc.c
+++ b/drivers/mmc/host/dw_mmc.c
@@ -972,6 +972,22 @@ static void dw_mci_request(struct mmc_host *mmc, struct mmc_request *mrq)
spin_unlock_bh(&host->lock);
}
+/*
+ * some of the boards use controller CD line for card detection.Unfortunately
+ * CD line is bind to the same volatge domain as of the IO lines.If we turn off
+ * IO voltage domain, CD line wont work.
+ * Return true when controller CD line is used for card detection or return
+ * false.
+ */
+static bool dw_mci_builtin_cd(struct dw_mci_slot *slot)
+{
+ struct dw_mci_board *brd = slot->host->pdata;
+ struct mmc_host *mmc = slot->mmc;
+
+ return (!(brd->quirks & DW_MCI_QUIRK_BROKEN_CARD_DETECTION) &&
+ IS_ERR_VALUE(mmc_gpio_get_cd(mmc))) ? 1 : 0;
+}
+
static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
{
struct dw_mci_slot *slot = mmc_priv(mmc);
@@ -1043,6 +1059,10 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
mci_writel(slot->host, PWREN, regs);
break;
case MMC_POWER_OFF:
+ if (dw_mci_builtin_cd(slot) &&
+ !test_bit(DW_MMC_CARD_PRESENT, &slot->flags))
+ return;
+
if (!IS_ERR(mmc->supply.vmmc))
mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, 0);
@@ -1055,6 +1075,8 @@ static void dw_mci_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
regs &= ~(1 << slot->id);
mci_writel(slot->host, PWREN, regs);
break;
+ case MMC_POWER_OFF_HARD:
+ break;
default:
break;
}
@@ -2310,6 +2332,9 @@ static int dw_mci_init_slot(struct dw_mci *host, unsigned int id)
else
clear_bit(DW_MMC_CARD_PRESENT, &slot->flags);
+ if (drv_data && drv_data->post_init)
+ drv_data->post_init(slot);
+
ret = mmc_add_host(mmc);
if (ret)
goto err_setup_bus;
diff --git a/drivers/mmc/host/dw_mmc.h b/drivers/mmc/host/dw_mmc.h
index 01b99e8..a3c2628 100644
--- a/drivers/mmc/host/dw_mmc.h
+++ b/drivers/mmc/host/dw_mmc.h
@@ -250,6 +250,7 @@ struct dw_mci_tuning_data {
* @prepare_command: handle CMD register extensions.
* @set_ios: handle bus specific extensions.
* @parse_dt: parse implementation specific device tree properties.
+ * @post_init: implementation specific post initialization.
* @execute_tuning: implementation specific tuning procedure.
*
* Provide controller implementation specific extensions. The usage of this
@@ -263,6 +264,7 @@ struct dw_mci_drv_data {
void (*prepare_command)(struct dw_mci *host, u32 *cmdr);
void (*set_ios)(struct dw_mci *host, struct mmc_ios *ios);
int (*parse_dt)(struct dw_mci *host);
+ void (*post_init)(struct dw_mci_slot *slot);
int (*execute_tuning)(struct dw_mci_slot *slot, u32 opcode,
struct dw_mci_tuning_data *tuning_data);
};
diff --git a/include/linux/mmc/host.h b/include/linux/mmc/host.h
index 4cbf614..5eb24ff 100644
--- a/include/linux/mmc/host.h
+++ b/include/linux/mmc/host.h
@@ -42,6 +42,7 @@ struct mmc_ios {
#define MMC_POWER_OFF 0
#define MMC_POWER_UP 1
#define MMC_POWER_ON 2
+#define MMC_POWER_OFF_HARD 3
unsigned char bus_width; /* data bus width */
@@ -283,6 +284,7 @@ struct mmc_host {
#define MMC_CAP2_HS400 (MMC_CAP2_HS400_1_8V | \
MMC_CAP2_HS400_1_2V)
#define MMC_CAP2_SDIO_IRQ_NOTHREAD (1 << 17)
+#define MMC_CAP2_CD_NEEDS_POWER (1 << 18) /* Card detect needs power */
mmc_pm_flag_t pm_caps; /* supported pm features */
--
1.7.10.4
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
