Hello Amit,
On 07/10/2014 12:08 PM, amit daniel kachhap wrote:
> On Fri, Jul 4, 2014 at 3:25 PM, Javier Martinez Canillas
> <javier.martinez@xxxxxxxxxxxxxxx> wrote:
>> MAX77686 PMIC support Dyamic Voltage Scaling (DVS) on a set
>> of Buck regulators. A number of GPIO are connected to these
>> lines and are requested by the mfd driver. Setup the GPIO
>> pins from the regulator driver.
> If possible merge this patch with patch 8. Both are adding DVS
> support. Put regmap_copy dependency patch in very beginning.
As Lee already said, I split the changes to minimize the cross-subsystem churn.
>>
>> Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
>> ---
>> drivers/regulator/max77686.c | 34 ++++++++++++++++++++++++++++++++++
>> 1 file changed, 34 insertions(+)
>>
>> diff --git a/drivers/regulator/max77686.c b/drivers/regulator/max77686.c
>> index ef1af2d..ecce77a 100644
>> --- a/drivers/regulator/max77686.c
>> +++ b/drivers/regulator/max77686.c
>> @@ -435,6 +435,12 @@ static int max77686_pmic_dt_parse_pdata(struct platform_device *pdev,
>> }
>> #endif /* CONFIG_OF */
>>
>> +static inline bool max77686_is_dvs_buck(int id)
>> +{
>> + /* BUCK 2,3 and 4 support DVS */
>> + return (id >= MAX77686_BUCK2 && id <= MAX77686_BUCK4);
> I am just wondering if along with above check, SELB gpios (if present)
> can be used to confirm if BUCK's are DVS based or not.
I don't know if SELB gpios being present or not should be used to determine
whether a BUCK includes the DVS feature. AFAIK boards could have some of these
lines hardwired and pulled high or low instead of using a GPIO.
>> +}
>> +
>> static int max77686_pmic_probe(struct platform_device *pdev)
>> {
>> struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent);
>> @@ -442,6 +448,9 @@ static int max77686_pmic_probe(struct platform_device *pdev)
>> struct max77686_data *max77686;
>> int i, ret = 0;
>> struct regulator_config config = { };
>> + unsigned int reg;
>> + int buck_default_idx;
>> + int buck_old_idx;
>>
>> dev_dbg(&pdev->dev, "%s\n", __func__);
>>
>> @@ -472,13 +481,34 @@ static int max77686_pmic_probe(struct platform_device *pdev)
>> config.driver_data = max77686;
>> platform_set_drvdata(pdev, max77686);
>>
>> + buck_default_idx = pdata->buck_default_idx;
>> + buck_old_idx = max77686_read_gpios(pdata);
>> +
>> for (i = 0; i < MAX77686_REGULATORS; i++) {
>> struct regulator_dev *rdev;
>> + int id = pdata->regulators[i].id;
>>
>> config.init_data = pdata->regulators[i].initdata;
>> config.of_node = pdata->regulators[i].of_node;
>>
>> max77686->opmode[i] = regulators[i].enable_mask;
>> +
>> + if (max77686_is_dvs_buck(id)) {
>> + /* Try to copy over data so we keep firmware settings */
>> + reg = regulators[i].vsel_reg;
>> +
>> + ret = regmap_reg_copy(iodev->regmap,
>> + reg + buck_default_idx,
>> + reg + buck_old_idx);
>> +
>> + if (ret)
>> + dev_warn(&pdev->dev, "Copy err %d => %d (%d)\n",
>> + reg + buck_old_idx,
>> + reg + buck_default_idx, ret);
>> +
>> + regulators[i].vsel_reg += buck_default_idx;
>> + }
>> +
>> rdev = devm_regulator_register(&pdev->dev,
>> ®ulators[i], &config);
>> if (IS_ERR(rdev)) {
>> @@ -488,6 +518,10 @@ static int max77686_pmic_probe(struct platform_device *pdev)
>> }
>> }
>>
>> + ret = max77686_setup_gpios(iodev->dev);
>> + if (ret)
>> + return ret;
>> +
>> return 0;
>> }
>>
>> --
>> 2.0.0.rc2
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
>> the body of a message to majordomo@xxxxxxxxxxxxxxx
>> More majordomo info at http://vger.kernel.org/majordomo-info.html
>
Best regards,
Javier
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
