On Fri, Jul 4, 2014 at 3:25 PM, Javier Martinez Canillas
<javier.martinez@xxxxxxxxxxxxxxx> wrote:
> MAX77686 PMIC support Dyamic Voltage Scaling (DVS) on a set
> of Buck regulators. A number of GPIO are connected to these
> lines and are requested by the mfd driver. Setup the GPIO
> pins from the regulator driver.
If possible merge this patch with patch 8. Both are adding DVS
support. Put regmap_copy dependency patch in very beginning.
>
> Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
> ---
> drivers/regulator/max77686.c | 34 ++++++++++++++++++++++++++++++++++
> 1 file changed, 34 insertions(+)
>
> diff --git a/drivers/regulator/max77686.c b/drivers/regulator/max77686.c
> index ef1af2d..ecce77a 100644
> --- a/drivers/regulator/max77686.c
> +++ b/drivers/regulator/max77686.c
> @@ -435,6 +435,12 @@ static int max77686_pmic_dt_parse_pdata(struct platform_device *pdev,
> }
> #endif /* CONFIG_OF */
>
> +static inline bool max77686_is_dvs_buck(int id)
> +{
> + /* BUCK 2,3 and 4 support DVS */
> + return (id >= MAX77686_BUCK2 && id <= MAX77686_BUCK4);
I am just wondering if along with above check, SELB gpios (if present)
can be used to confirm if BUCK's are DVS based or not.
> +}
> +
> static int max77686_pmic_probe(struct platform_device *pdev)
> {
> struct max77686_dev *iodev = dev_get_drvdata(pdev->dev.parent);
> @@ -442,6 +448,9 @@ static int max77686_pmic_probe(struct platform_device *pdev)
> struct max77686_data *max77686;
> int i, ret = 0;
> struct regulator_config config = { };
> + unsigned int reg;
> + int buck_default_idx;
> + int buck_old_idx;
>
> dev_dbg(&pdev->dev, "%s\n", __func__);
>
> @@ -472,13 +481,34 @@ static int max77686_pmic_probe(struct platform_device *pdev)
> config.driver_data = max77686;
> platform_set_drvdata(pdev, max77686);
>
> + buck_default_idx = pdata->buck_default_idx;
> + buck_old_idx = max77686_read_gpios(pdata);
> +
> for (i = 0; i < MAX77686_REGULATORS; i++) {
> struct regulator_dev *rdev;
> + int id = pdata->regulators[i].id;
>
> config.init_data = pdata->regulators[i].initdata;
> config.of_node = pdata->regulators[i].of_node;
>
> max77686->opmode[i] = regulators[i].enable_mask;
> +
> + if (max77686_is_dvs_buck(id)) {
> + /* Try to copy over data so we keep firmware settings */
> + reg = regulators[i].vsel_reg;
> +
> + ret = regmap_reg_copy(iodev->regmap,
> + reg + buck_default_idx,
> + reg + buck_old_idx);
> +
> + if (ret)
> + dev_warn(&pdev->dev, "Copy err %d => %d (%d)\n",
> + reg + buck_old_idx,
> + reg + buck_default_idx, ret);
> +
> + regulators[i].vsel_reg += buck_default_idx;
> + }
> +
> rdev = devm_regulator_register(&pdev->dev,
> ®ulators[i], &config);
> if (IS_ERR(rdev)) {
> @@ -488,6 +518,10 @@ static int max77686_pmic_probe(struct platform_device *pdev)
> }
> }
>
> + ret = max77686_setup_gpios(iodev->dev);
> + if (ret)
> + return ret;
> +
> return 0;
> }
>
> --
> 2.0.0.rc2
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
