Add Device Tree binding documentation for Maxim 77802 PMIC.
Signed-off-by: Javier Martinez Canillas <javier.martinez@xxxxxxxxxxxxxxx>
---
Changes since v5:
- Use max77686,* properties instead of max77802,* since the support is
now in the max77686 driver and that IP defined the properties first.
- Fix issues in DT binding documentation. Suggested by Andreas Farber.
Changes since v4: None
Changes since v3: None
Changes since v2:
- Explain better the Dynamic Voltage Scaling (DVS) support in some Buck
regulators and the max77802,pmic-buck-{dvs,selb}-gpios properties.
Suggested by Mark Brown.
---
Documentation/devicetree/bindings/mfd/max77802.txt | 95 ++++++++++++++++++++++
1 file changed, 95 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/max77802.txt
diff --git a/Documentation/devicetree/bindings/mfd/max77802.txt b/Documentation/devicetree/bindings/mfd/max77802.txt
new file mode 100644
index 0000000..5460e20
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/max77802.txt
@@ -0,0 +1,95 @@
+Maxim MAX77802 multi-function device
+
+MAX77802 is a Multifunction device with PMIC, RTC and Charger on chip. It is
+interfaced to host controller using i2c interface. PMIC, Charger and RTC
+submodules are addressed using same i2c slave address.
+
+Buck regulators 1, 2, 3, 4 and 6 include Dynamic Voltage Scaling (DVS) that
+allows each output voltage to change dynamically. Each Buck output voltage
+is selected using a set of external inputs: DVS1-3 and SELB1, 2, 3, 4 and 6.
+
+There are 8 DVS registers that can be used to configure the output voltage
+for each Buck regulator and which one is active is controled by DVSx lines.
+
+SELBx lines are used to control if individual Buck lines are ON or OFF.
+
+This document describes the binding for mfd device and PMIC submodule.
+
+Binding for the built-in 32k clock generator block is defined separately
+in bindings/clk/maxim,max77802.txt file.
+
+Required properties:
+- compatible : Must be "maxim,max77802";
+- reg : Specifies the i2c slave address of PMIC block.
+- interrupts : This i2c device has an IRQ line connected to the main SoC.
+- interrupt-parent : The parent interrupt controller.
+
+Optional properties:
+- max77686,pmic-buck-default-dvs-idx: We'll always write this DVS index in the
+ PMIC for Bucks with DVS.
+ NOTE: at the moment these bindings don't include enough details for actual
+ GPIO-DVS--this just lets you choose which single slot to use.
+
+- max77686,pmic-buck-dvs-gpios: A GPIO array where each GPIO is connected to a
+ DVS line. We'll try to set these GPIOs to match pmic-buck-default-dvs-idx at
+ probe time if they are defined. If some or all of these GPIOs are not defined
+ it's assumed that the board has any missing GPIOs hardwired to match
+ pmic-buck-default-dvs-idx.
+
+- max77686,pmic-buck-selb-gpios: A GPIO array where each GPIO is connected to a
+ SELBx line. Should be five values: 1, 2, 3, 4, 6. It is strongly suggested to
+ include these GPIOs if there's any chance that changing DVS GPIOs one line at
+ a time might glitch your DVS values.
+
+Optional node:
+- regulators : The regulators of max77802 have to be instantiated
+ under subnode named "regulators" using the following format.
+
+ regulator-name {
+ standard regulator constraints....
+ };
+ refer Documentation/devicetree/bindings/regulator/regulator.txt
+
+ The regulator node name should be initialized with a string
+to get matched with their hardware counterparts as follow. The valid names are:
+
+ -LDOn : for LDOs, where n can lie in range 1 to 35.
+ example: LDO1, LDO2, LDO35.
+ -BUCKn : for BUCKs, where n can lie in range 1 to 10.
+ example: BUCK1, BUCK5, BUCK10.
+Example:
+
+ max77802@09 {
+ compatible = "maxim,max77802";
+ interrupt-parent = <&wakeup_eint>;
+ interrupts = <26 0>;
+ reg = <0x09>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ max77686,pmic-buck-default-dvs-idx = <1>;
+ max77686,pmic-buck-dvs-gpios = <&gpy7 6 0>,
+ <&gpj4 2 0>,
+ <&gpj4 3 0>;
+ max77686,pmic-buck-selb-gpios = <&gph0 2 0>,
+ <&gph0 3 0>,
+ <&gph0 4 0>,
+ <&gph0 5 0>,
+ <&gph0 6 0>;
+
+ regulators {
+ ldo11_reg: LDO11 {
+ regulator-name = "vdd_ldo11";
+ regulator-min-microvolt = <1900000>;
+ regulator-max-microvolt = <1900000>;
+ regulator-always-on;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "vdd_mif";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1300000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
--
2.0.0.rc2
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
