Hi Kumar Gala, > From: Kumar Gala [mailto:galak@xxxxxxxxxxxxxx] > Sent: Friday, October 25, 2013 11:36 PM > > On Oct 25, 2013, at 9:15 AM, Kamil Debski wrote: > > > Add a new driver for the Exynos USB PHY. The new driver uses the > > generic PHY framework. The driver includes support for the Exynos > 4x10 > > and 4x12 SoC families. > > > > Signed-off-by: Kamil Debski <k.debski@xxxxxxxxxxx> > > Signed-off-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx> > > --- > > .../devicetree/bindings/phy/samsung-usbphy.txt | 51 +++ > > drivers/phy/Kconfig | 21 ++ > > drivers/phy/Makefile | 3 + > > drivers/phy/phy-exynos-usb.c | 245 > ++++++++++++++ > > drivers/phy/phy-exynos-usb.h | 94 ++++++ > > drivers/phy/phy-exynos4210-usb.c | 295 > +++++++++++++++++ > > drivers/phy/phy-exynos4212-usb.c | 343 > ++++++++++++++++++++ > > 7 files changed, 1052 insertions(+) > > create mode 100644 > > Documentation/devicetree/bindings/phy/samsung-usbphy.txt > > create mode 100644 drivers/phy/phy-exynos-usb.c create mode 100644 > > drivers/phy/phy-exynos-usb.h create mode 100644 > > drivers/phy/phy-exynos4210-usb.c create mode 100644 > > drivers/phy/phy-exynos4212-usb.c > > > > diff --git a/Documentation/devicetree/bindings/phy/samsung-usbphy.txt > > b/Documentation/devicetree/bindings/phy/samsung-usbphy.txt > > new file mode 100644 > > index 0000000..f112b37 > > --- /dev/null > > +++ b/Documentation/devicetree/bindings/phy/samsung-usbphy.txt > > @@ -0,0 +1,51 @@ > > +Samsung S5P/EXYNOS SoC series USB PHY > > +------------------------------------------------- > > + > > +Required properties: > > +- compatible : should be one of the listed compatibles: > > + - "samsung,exynos4210-usbphy" > > + - "samsung,exynos4212-usbphy" > > +- reg : a list of registers used by phy driver > > + - first and obligatory is the location of phy modules registers > > + - second and also required is the location of isolation registers > > + (isolation registers control the physical connection between > the in > > + SoC modules and outside of the SoC, this also can be called > enable > > + control in the documentation of the SoC) > > + - third is the location of the mode switch register, this only > applies > > + to SoCs that have such a feature; mode switching enables to > have > > + both host and device used the same SoC pins and is commonly > used > > + when OTG is supported > > +- #phy-cells : from the generic phy bindings, must be 1; > > Please add if clock & clock-names are required properties. Ok, thanks for pointing this out. > > > + > > +The second cell in the PHY specifier identifies the PHY its meaning > > +is SoC dependent. For the currently supported SoCs (Exynos 4210 and > > +Exynos 4212) it is as follows: > > Can we say instead of 'its meaning is SoC dependent...' something like > 'its meaning is compatible dependent"? Ok, this sounds better in deed. > > + 0 - USB device, > > + 1 - USB host, > > + 2 - HSIC0, > > + 3 - HSIC1, > > + > > +Example: > > + > > +For Exynos 4412 (compatible with Exynos 4212): > > + > > +exynos_usbphy: exynos-usbphy@125B0000 { > > + compatible = "samsung,exynos4212-usbphy"; > > + reg = <0x125B0000 0x100 0x10020704 0x0c 0x1001021c 0x4>; > > + ranges; > > + #address-cells = <1>; > > + #size-cells = <1>; > > Why do you have ranges, and #address-cells & #size-cells here? As, I mentioned in my reply to Kishon. I worked on two branches and I forgot to remove this in the one used to generate patches. > > > + clocks = <&clock 305>, <&clock 2>, <&clock 2>, <&clock 2>, > > + <&clock 2>; > > + clock-names = "phy", "device", "host", "hsic0", "hsic1"; > > + status = "okay"; > > + #phy-cells = <1>; > > +}; > > + > > +Then the PHY can be used in other nodes such as: > > + > > +ehci@12580000 { > > + status = "okay"; > > + phys = <&exynos_usbphy 2>; > > + phy-names = "hsic0"; > > +}; > Best wishes, -- Kamil Debski Samsung R&D Institute Poland -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |