On Tuesday, July 23, 2013 3:30 PM, Kishon Vijay Abraham I wrote: > On Tuesday 23 July 2013 06:44 AM, Jingoo Han wrote: > > On Tuesday, July 23, 2013 12:04 AM, Kishon Vijay Abraham I wrote: > >> On Thursday 18 July 2013 10:51 AM, Jingoo Han wrote: > >>> Exynos PCIe IP consists of Synopsys specific part and Exynos > >>> specific part. Only core block is a Synopsys designware part; > >>> other parts are Exynos specific. > >>> Also, the Synopsys designware part can be shared with other > >>> platforms; thus, it can be split two parts such as Synopsys > >>> designware part and Exynos specific part. > >> > >> some more queries and comments.. > > > . > . > <snip> > . > . > >>> + of_pci_range_to_resource(&range, np, &pp->cfg); > >>> + pp->config.cfg0_size = resource_size(&pp->cfg)/2; > >>> + pp->config.cfg1_size = resource_size(&pp->cfg)/2; > >>> + } > >>> + } > >>> + > >>> + pp->dbi_base = devm_ioremap(pp->dev, pp->cfg.start, > >>> + resource_size(&pp->cfg)); [.....] > > > >> Why should it be same as dbi_base? > >> AFAIK, jacinto6 has a dedicated configuration/io/memory space that is entirely > >> different from dbi_base. > > > > According to the Synopsys designware PCIe datasheet, > > in chapter 5.1.1 Register Space Layout, > > 'Port Logic Registers' are placed between (config space 0x0 + 0x700) > > and (config space 0x0 + 0xFFF). > > 'dbi_base' is used for reading/writing 'Port Logic Registers'. > > Exynos are using 'dbi_base' like this. Thus, the base addresses of > > both 'dbi_base' and configuration/io/memory space are same. > > > > Just now, I looked at Spear PCIe driver. > > However, in the case of Spear, the base address of configuration/io/memory > > space is defined as 0x80000000. The base address of 'Port Logic Registers' > > is defined as 0xb1000000. > > I think that the situation of 'jacinto6' is similar with Spear, right? > > > > Then, I will move pp->dbi_base mapping code from pcie-designware.c > > to pci-exynos.c. > > I think you need not move this to exynos (since registers in dbi_base is common > for all platforms) but modify the pcie-designware.c to use different address > space for dbi_base. In your case, you'll duplicate the address space for > dbi_base and configuration space. > I will map 'pp->dbi_base' as below: Also, I referenced SPEAr PCIe patches made by Pratyush Anand. (http://permalink.gmane.org/gmane.linux.kernel.pci/18400) (http://permalink.gmane.org/gmane.linux.kernel.pci/18403) 1. The different addresses between dbi_base and configuration space : SPEAr PCIe, OMAP PCIe 'pp->dbi_base' value is come from DT binding, then, 'pp->dbi_base' will be mapped in spear_pcie_probe() in pci-spear.c (arch/arm/boot/dts/spear13xx.dtsi) pcie0@b1000000 { reg = <0xb1000000 0x2000 <-- dbi register 0xb1002000 0x7fdfff <-- elbi register (drivers/pci/host/pci-spear.c) static int __init spear_pcie_probe(struct platform_device *pdev) { struct resource *dbi_base; struct resource *elbi_base; dbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); pp->dbi_base = devm_ioremap_resource(&pdev->dev, dbi_base); elbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 1); spear_pcie->elbi_base = devm_ioremap_resource(&pdev->dev, elbi_base); 2. The same addresses between dbi_base and configuration space : Exynos PCIe 'pp->dbi_base' will be mapped in dw_pcie_host_init() of pcie-designware.c. (drivers/pci/host/pcie-exynos.c) static int __init exynos_pcie_probe(struct platform_device *pdev) { struct resource *elbi_base; elbi_base = platform_get_resource(pdev, IORESOURCE_MEM, 0); exynos_pcie->elbi_base = devm_ioremap_resource(&pdev->dev, elbi_base); (drivers/pci/host/pcie-designware.c) int dw_pcie_host_init(struct pcie_port *pp) { if (!pp->dbi_base) { pp->dbi_base = devm_ioremap(pp->dev, pp->cfg.start, resource_size(&pp->cfg)); if (!pp->dbi_base) { dev_err(pp->dev, "error with ioremap\n"); return -ENOMEM; } } Best regards, Jingoo Han -- To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
 |