The S3C2416/S3C2450 SoCs support two sources for the armclk.
The first source is the so called armdiv which divides the msysclk down
to provide necessary cpu rates. In this mode the core voltage must be
always at 1.3V. The frequency from the armdiv is not allowed to be
lower than the hclk frequency.
In the second mode the armclk can be sourced directly from the hclk in
the so called "dynamic voltags scaling" (dvs) mode. Here the armdiv
isn't used at all. Also in this mode the core voltage may be lowered.
Existing hardware and tests with it suggest 1.0V as sufficient.
When changing the clock source to the armdiv from the hclk, the SoC
shows stability issues if the new frequency is higher than the current
hclk frequency. Hence the driver always forces the armdiv to the hclk
frequency before the source change and lets the cpufreq issue another
set_target call for higher frequencies.
To mark the hclk frequency as lower as the corresponding armdiv
frequency it is set 1MHz below the real frequency. This lets the cpufreq
framework change between 133MHz based on hclk and 133MHz based on armdiv
at will.
Signed-off-by: Heiko Stuebner <heiko@xxxxxxxxx>
Tested-by: Andrey Gusakov <dron0gus@xxxxxxxxx>
---
changes since v1: correct the frequencies of the S3C2450 variant
changes since RFC: reboot-notifier to leave dvs mode on reboot
and a lot of cleanups
drivers/cpufreq/Kconfig.arm | 22 ++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/s3c2416-cpufreq.c | 542 +++++++++++++++++++++++++++++++++++++
3 files changed, 565 insertions(+), 0 deletions(-)
create mode 100644 drivers/cpufreq/s3c2416-cpufreq.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index e0664fe..fa85e59 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -2,6 +2,28 @@
# ARM CPU Frequency scaling drivers
#
+config ARM_S3C2416_CPUFREQ
+ bool "S3C2416 CPU Frequency scaling support"
+ depends on CPU_S3C2416
+ help
+ This adds the CPUFreq driver for the Samsung S3C2416 and
+ S3C2450 SoC. The S3C2416 supports changing the rate of the
+ armdiv clock source and also entering a so called dynamic
+ voltage scaling mode in which it is possible to reduce the
+ core voltage of the cpu.
+
+ If in doubt, say N.
+
+config ARM_S3C2416_CPUFREQ_VCORESCALE
+ bool "Allow voltage scaling for S3C2416 arm core (EXPERIMENTAL)"
+ depends on ARM_S3C2416_CPUFREQ && REGULATOR && EXPERIMENTAL
+ help
+ Enable CPU voltage scaling when entering the dvs mode.
+ It uses information gathered through existing hardware and
+ tests but not documented in any datasheet.
+
+ If in doubt, say N.
+
config ARM_S3C64XX_CPUFREQ
bool "Samsung S3C64XX"
depends on CPU_S3C6410
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index ac000fa..042fbae 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -40,6 +40,7 @@ obj-$(CONFIG_X86_CPUFREQ_NFORCE2) += cpufreq-nforce2.o
##################################################################################
# ARM SoC drivers
obj-$(CONFIG_UX500_SOC_DB8500) += db8500-cpufreq.o
+obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
obj-$(CONFIG_ARM_S3C64XX_CPUFREQ) += s3c64xx-cpufreq.o
obj-$(CONFIG_ARM_S5PV210_CPUFREQ) += s5pv210-cpufreq.o
obj-$(CONFIG_ARM_EXYNOS_CPUFREQ) += exynos-cpufreq.o
diff --git a/drivers/cpufreq/s3c2416-cpufreq.c b/drivers/cpufreq/s3c2416-cpufreq.c
new file mode 100644
index 0000000..50d2f15
--- /dev/null
+++ b/drivers/cpufreq/s3c2416-cpufreq.c
@@ -0,0 +1,542 @@
+/*
+ * S3C2416/2450 CPUfreq Support
+ *
+ * Copyright 2011 Heiko Stuebner <heiko@xxxxxxxxx>
+ *
+ * based on s3c64xx_cpufreq.c
+ *
+ * Copyright 2009 Wolfson Microelectronics plc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/init.h>
+#include <linux/cpufreq.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reboot.h>
+#include <linux/module.h>
+
+static DEFINE_MUTEX(cpufreq_lock);
+
+struct s3c2416_data {
+ struct clk *armdiv;
+ struct clk *armclk;
+ struct clk *hclk;
+
+ unsigned long regulator_latency;
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ struct regulator *vddarm;
+#endif
+
+ struct cpufreq_frequency_table *freq_table;
+
+ bool is_dvs;
+ bool disable_dvs;
+};
+
+static struct s3c2416_data s3c2416_cpufreq;
+
+struct s3c2416_dvfs {
+ unsigned int vddarm_min;
+ unsigned int vddarm_max;
+};
+
+/* pseudo-frequency for dvs mode */
+#define FREQ_DVS 132333
+
+/* frequency to sleep and reboot in
+ * it's essential to leave dvs, as some boards do not reconfigure the
+ * regulator on reboot
+ */
+#define FREQ_SLEEP 133333
+
+/* Sources for the ARMCLK */
+#define SOURCE_HCLK 0
+#define SOURCE_ARMDIV 1
+
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+/* S3C2416 only supports changing the voltage in the dvs-mode.
+ * Voltages down to 1.0V seem to work, so we take what the regulator
+ * can get us.
+ */
+static struct s3c2416_dvfs s3c2416_dvfs_table[] = {
+ [SOURCE_HCLK] = { 950000, 1250000 },
+ [SOURCE_ARMDIV] = { 1250000, 1350000 },
+};
+#endif
+
+static struct cpufreq_frequency_table s3c2416_freq_table[] = {
+ { SOURCE_HCLK, FREQ_DVS },
+ { SOURCE_ARMDIV, 133333 },
+ { SOURCE_ARMDIV, 266666 },
+ { SOURCE_ARMDIV, 400000 },
+ { 0, CPUFREQ_TABLE_END },
+};
+
+static struct cpufreq_frequency_table s3c2450_freq_table[] = {
+ { SOURCE_HCLK, FREQ_DVS },
+ { SOURCE_ARMDIV, 133500 },
+ { SOURCE_ARMDIV, 267000 },
+ { SOURCE_ARMDIV, 534000 },
+ { 0, CPUFREQ_TABLE_END },
+};
+
+static int s3c2416_cpufreq_verify_speed(struct cpufreq_policy *policy)
+{
+ struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
+
+ if (policy->cpu != 0)
+ return -EINVAL;
+
+ return cpufreq_frequency_table_verify(policy, s3c_freq->freq_table);
+}
+
+static unsigned int s3c2416_cpufreq_get_speed(unsigned int cpu)
+{
+ struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
+
+ if (cpu != 0)
+ return 0;
+
+ /* return our pseudo-frequency when in dvs mode */
+ if (s3c_freq->is_dvs)
+ return FREQ_DVS;
+
+ return clk_get_rate(s3c_freq->armclk) / 1000;
+}
+
+static int s3c2416_cpufreq_set_armdiv(struct s3c2416_data *s3c_freq,
+ unsigned int freq)
+{
+ int ret;
+
+ if (clk_get_rate(s3c_freq->armdiv) / 1000 != freq) {
+ ret = clk_set_rate(s3c_freq->armdiv, freq * 1000);
+ if (ret < 0) {
+ pr_err("cpufreq: Failed to set armdiv rate %dkHz: %d\n",
+ freq, ret);
+ return ret;
+ }
+ }
+
+ return 0;
+}
+
+static int s3c2416_cpufreq_enter_dvs(struct s3c2416_data *s3c_freq, int idx)
+{
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ struct s3c2416_dvfs *dvfs;
+#endif
+ int ret;
+
+ if (s3c_freq->is_dvs) {
+ pr_debug("cpufreq: already in dvs mode, nothing to do\n");
+ return 0;
+ }
+
+ pr_debug("cpufreq: switching armclk to hclk (%lukHz)\n",
+ clk_get_rate(s3c_freq->hclk) / 1000);
+ ret = clk_set_parent(s3c_freq->armclk, s3c_freq->hclk);
+ if (ret < 0) {
+ pr_err("cpufreq: Failed to switch armclk to hclk: %d\n", ret);
+ return ret;
+ }
+
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ /* changing the core voltage is only allowed when in dvs mode */
+ if (s3c_freq->vddarm) {
+ dvfs = &s3c2416_dvfs_table[idx];
+
+ pr_debug("cpufreq: setting regultor to %d-%d\n",
+ dvfs->vddarm_min, dvfs->vddarm_max);
+ ret = regulator_set_voltage(s3c_freq->vddarm,
+ dvfs->vddarm_min,
+ dvfs->vddarm_max);
+
+ /* when lowering the voltage failed, there is nothing to do */
+ if (ret != 0)
+ pr_err("cpufreq: Failed to set VDDARM: %d\n", ret);
+ }
+#endif
+
+ s3c_freq->is_dvs = 1;
+
+ return 0;
+}
+
+static int s3c2416_cpufreq_leave_dvs(struct s3c2416_data *s3c_freq, int idx)
+{
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ struct s3c2416_dvfs *dvfs;
+#endif
+ int ret;
+
+ if (!s3c_freq->is_dvs) {
+ pr_debug("cpufreq: not in dvs mode, so can't leave\n");
+ return 0;
+ }
+
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ if (s3c_freq->vddarm) {
+ dvfs = &s3c2416_dvfs_table[idx];
+
+ pr_debug("cpufreq: setting regultor to %d-%d\n",
+ dvfs->vddarm_min, dvfs->vddarm_max);
+ ret = regulator_set_voltage(s3c_freq->vddarm,
+ dvfs->vddarm_min,
+ dvfs->vddarm_max);
+ if (ret != 0) {
+ pr_err("cpufreq: Failed to set VDDARM: %d\n", ret);
+ return ret;
+ }
+ }
+#endif
+
+ /* force armdiv to hclk frequency for transition from dvs*/
+ if (clk_get_rate(s3c_freq->armdiv) > clk_get_rate(s3c_freq->hclk)) {
+ pr_debug("cpufreq: force armdiv to hclk frequency (%lukHz)\n",
+ clk_get_rate(s3c_freq->hclk) / 1000);
+ ret = s3c2416_cpufreq_set_armdiv(s3c_freq,
+ clk_get_rate(s3c_freq->hclk) / 1000);
+ if (ret < 0) {
+ pr_err("cpufreq: Failed to to set the armdiv to %lukHz: %d\n",
+ clk_get_rate(s3c_freq->hclk) / 1000, ret);
+ return ret;
+ }
+ }
+
+ pr_debug("cpufreq: switching armclk parent to armdiv (%lukHz)\n",
+ clk_get_rate(s3c_freq->armdiv) / 1000);
+
+ ret = clk_set_parent(s3c_freq->armclk, s3c_freq->armdiv);
+ if (ret < 0) {
+ pr_err("cpufreq: Failed to switch armclk clock parent to armdiv: %d\n",
+ ret);
+ return ret;
+ }
+
+ s3c_freq->is_dvs = 0;
+
+ return 0;
+}
+
+static int s3c2416_cpufreq_set_target(struct cpufreq_policy *policy,
+ unsigned int target_freq,
+ unsigned int relation)
+{
+ struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
+ struct cpufreq_freqs freqs;
+ int idx, ret, to_dvs = 0;
+ unsigned int i;
+
+ mutex_lock(&cpufreq_lock);
+
+ pr_debug("cpufreq: to %dKHz, relation %d\n", target_freq, relation);
+
+ ret = cpufreq_frequency_table_target(policy, s3c_freq->freq_table,
+ target_freq, relation, &i);
+ if (ret != 0)
+ goto out;
+
+ idx = s3c_freq->freq_table[i].index;
+
+ if (idx == SOURCE_HCLK)
+ to_dvs = 1;
+
+ /* switching to dvs when it's not allowed */
+ if (to_dvs && s3c_freq->disable_dvs) {
+ pr_debug("cpufreq: entering dvs mode not allowed\n");
+ ret = -EINVAL;
+ goto out;
+ }
+
+ freqs.cpu = 0;
+ freqs.flags = 0;
+ freqs.old = s3c_freq->is_dvs ? FREQ_DVS
+ : clk_get_rate(s3c_freq->armclk) / 1000;
+
+ /* When leavin dvs mode, always switch the armdiv to the hclk rate
+ * The S3C2416 has stability issues when switching directly to
+ * higher frequencies.
+ */
+ freqs.new = (s3c_freq->is_dvs && !to_dvs)
+ ? clk_get_rate(s3c_freq->hclk) / 1000
+ : s3c_freq->freq_table[i].frequency;
+
+ pr_debug("cpufreq: Transition %d-%dkHz\n", freqs.old, freqs.new);
+
+ if (!to_dvs && freqs.old == freqs.new)
+ goto out;
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_PRECHANGE);
+
+ if (to_dvs) {
+ pr_debug("cpufreq: enter dvs\n");
+ ret = s3c2416_cpufreq_enter_dvs(s3c_freq, idx);
+ } else if (s3c_freq->is_dvs) {
+ pr_debug("cpufreq: leave dvs\n");
+ ret = s3c2416_cpufreq_leave_dvs(s3c_freq, idx);
+ } else {
+ pr_debug("cpufreq: change armdiv to %dkHz\n", freqs.new);
+ ret = s3c2416_cpufreq_set_armdiv(s3c_freq, freqs.new);
+ }
+
+ cpufreq_notify_transition(&freqs, CPUFREQ_POSTCHANGE);
+
+out:
+ mutex_unlock(&cpufreq_lock);
+
+ return ret;
+}
+
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+static void __init s3c2416_cpufreq_cfg_regulator(struct s3c2416_data *s3c_freq)
+{
+ int count, v, i, found;
+ struct cpufreq_frequency_table *freq;
+ struct s3c2416_dvfs *dvfs;
+
+ count = regulator_count_voltages(s3c_freq->vddarm);
+ if (count < 0) {
+ pr_err("cpufreq: Unable to check supported voltages\n");
+ return;
+ }
+
+ freq = s3c_freq->freq_table;
+ while (count > 0 && freq->frequency != CPUFREQ_TABLE_END) {
+ if (freq->frequency == CPUFREQ_ENTRY_INVALID)
+ continue;
+
+ dvfs = &s3c2416_dvfs_table[freq->index];
+ found = 0;
+
+ /* Check only the min-voltage, more is always ok on S3C2416 */
+ for (i = 0; i < count; i++) {
+ v = regulator_list_voltage(s3c_freq->vddarm, i);
+ if (v >= dvfs->vddarm_min)
+ found = 1;
+ }
+
+ if (!found) {
+ pr_debug("cpufreq: %dkHz unsupported by regulator\n",
+ freq->frequency);
+ freq->frequency = CPUFREQ_ENTRY_INVALID;
+ }
+
+ freq++;
+ }
+
+ /* Guessed */
+ s3c_freq->regulator_latency = 1 * 1000 * 1000;
+}
+#endif
+
+static int s3c2416_cpufreq_reboot_notifier_evt(struct notifier_block *this,
+ unsigned long event, void *ptr)
+{
+ struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
+ int ret;
+
+ mutex_lock(&cpufreq_lock);
+
+ /* disable further changes */
+ s3c_freq->disable_dvs = 1;
+
+ mutex_unlock(&cpufreq_lock);
+
+ /* some boards don't reconfigure the regulator on reboot, which
+ * could lead to undervolting the cpu when the clock is reset.
+ * Therefore we always leave the DVS mode on reboot.
+ */
+ if (s3c_freq->is_dvs) {
+ pr_debug("cpufreq: leave dvs on reboot\n");
+ ret = cpufreq_driver_target(cpufreq_cpu_get(0), FREQ_SLEEP, 0);
+ if (ret < 0)
+ return NOTIFY_BAD;
+ }
+
+ return NOTIFY_DONE;
+}
+
+static struct notifier_block s3c2416_cpufreq_reboot_notifier = {
+ .notifier_call = s3c2416_cpufreq_reboot_notifier_evt,
+};
+
+static int __init s3c2416_cpufreq_driver_init(struct cpufreq_policy *policy)
+{
+ struct s3c2416_data *s3c_freq = &s3c2416_cpufreq;
+ struct cpufreq_frequency_table *freq;
+ struct clk *msysclk;
+ unsigned long rate;
+ int ret;
+
+ if (policy->cpu != 0)
+ return -EINVAL;
+
+ msysclk = clk_get(NULL, "msysclk");
+ if (IS_ERR(msysclk)) {
+ ret = PTR_ERR(msysclk);
+ pr_err("cpufreq: Unable to obtain msysclk: %d\n", ret);
+ return ret;
+ }
+
+ /*
+ * S3C2416 and S3C2450 share the same processor-ID and also provide no
+ * other means to distinguish them other than through the rate of
+ * msysclk. On S3C2416 msysclk runs at 800MHz and on S3C2450 at 533MHz.
+ */
+ rate = clk_get_rate(msysclk);
+ if (rate == 800 * 1000 * 1000) {
+ pr_info("cpufreq: msysclk running at %lukHz, using S3C2416 frequency table\n",
+ rate / 1000);
+ s3c_freq->freq_table = s3c2416_freq_table;
+ policy->cpuinfo.max_freq = 400000;
+ } else if (rate / 1000 == 534000) {
+ pr_info("cpufreq: msysclk running at %lukHz, using S3C2450 frequency table\n",
+ rate / 1000);
+ s3c_freq->freq_table = s3c2450_freq_table;
+ policy->cpuinfo.max_freq = 534000;
+ }
+
+ /* not needed anymore */
+ clk_put(msysclk);
+
+ if (s3c_freq->freq_table == NULL) {
+ pr_err("cpufreq: No frequency information for this CPU, msysclk at %lukHz\n",
+ rate / 1000);
+ return -ENODEV;
+ }
+
+ s3c_freq->is_dvs = 0;
+
+ s3c_freq->armdiv = clk_get(NULL, "armdiv");
+ if (IS_ERR(s3c_freq->armdiv)) {
+ ret = PTR_ERR(s3c_freq->armdiv);
+ pr_err("cpufreq: Unable to obtain ARMDIV: %d\n", ret);
+ return ret;
+ }
+
+ s3c_freq->hclk = clk_get(NULL, "hclk");
+ if (IS_ERR(s3c_freq->hclk)) {
+ ret = PTR_ERR(s3c_freq->hclk);
+ pr_err("cpufreq: Unable to obtain HCLK: %d\n", ret);
+ goto err_hclk;
+ }
+
+ /* chech hclk rate, we only support the common 133MHz for now
+ * hclk could also run at 66MHz, but this not often used
+ */
+ rate = clk_get_rate(s3c_freq->hclk);
+ if (rate < 133 * 1000 * 1000) {
+ pr_err("cpufreq: HCLK not at 133MHz\n");
+ clk_put(s3c_freq->hclk);
+ ret = -EINVAL;
+ goto err_armclk;
+ }
+
+ s3c_freq->armclk = clk_get(NULL, "armclk");
+ if (IS_ERR(s3c_freq->armclk)) {
+ ret = PTR_ERR(s3c_freq->armclk);
+ pr_err("cpufreq: Unable to obtain ARMCLK: %d\n", ret);
+ goto err_armclk;
+ }
+
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ s3c_freq->vddarm = regulator_get(NULL, "vddarm");
+ if (IS_ERR(s3c_freq->vddarm)) {
+ ret = PTR_ERR(s3c_freq->vddarm);
+ pr_err("cpufreq: Failed to obtain VDDARM: %d\n", ret);
+ goto err_vddarm;
+ }
+
+ s3c2416_cpufreq_cfg_regulator(s3c_freq);
+#else
+ s3c_freq->regulator_latency = 0;
+#endif
+
+ freq = s3c_freq->freq_table;
+ while (freq->frequency != CPUFREQ_TABLE_END) {
+ /* special handling for dvs mode */
+ if (freq->index == 0) {
+ if (!s3c_freq->hclk) {
+ pr_debug("cpufreq: %dkHz unsupported as it would need unavailable dvs mode\n",
+ freq->frequency);
+ freq->frequency = CPUFREQ_ENTRY_INVALID;
+ } else {
+ freq++;
+ continue;
+ }
+ }
+
+ /* Check for frequencies we can generate */
+ rate = clk_round_rate(s3c_freq->armdiv,
+ freq->frequency * 1000);
+ rate /= 1000;
+ if (rate != freq->frequency) {
+ pr_debug("cpufreq: %dkHz unsupported by clock (clk_round_rate return %lu)\n",
+ freq->frequency, rate);
+ freq->frequency = CPUFREQ_ENTRY_INVALID;
+ }
+
+ freq++;
+ }
+
+ policy->cur = clk_get_rate(s3c_freq->armclk) / 1000;
+
+ /* Datasheet says PLL stabalisation time must be at least 300us,
+ * so but add some fudge. (reference in LOCKCON0 register description)
+ */
+ policy->cpuinfo.transition_latency = (500 * 1000) +
+ s3c_freq->regulator_latency;
+
+ ret = cpufreq_frequency_table_cpuinfo(policy, s3c_freq->freq_table);
+ if (ret)
+ goto err_freq_table;
+
+ cpufreq_frequency_table_get_attr(s3c_freq->freq_table, 0);
+
+ register_reboot_notifier(&s3c2416_cpufreq_reboot_notifier);
+
+ return 0;
+
+err_freq_table:
+#ifdef CONFIG_ARM_S3C2416_CPUFREQ_VCORESCALE
+ regulator_put(s3c_freq->vddarm);
+err_vddarm:
+#endif
+ clk_put(s3c_freq->armclk);
+err_armclk:
+ clk_put(s3c_freq->hclk);
+err_hclk:
+ clk_put(s3c_freq->armdiv);
+
+ return ret;
+}
+
+static struct freq_attr *s3c2416_cpufreq_attr[] = {
+ &cpufreq_freq_attr_scaling_available_freqs,
+ NULL,
+};
+
+static struct cpufreq_driver s3c2416_cpufreq_driver = {
+ .owner = THIS_MODULE,
+ .flags = 0,
+ .verify = s3c2416_cpufreq_verify_speed,
+ .target = s3c2416_cpufreq_set_target,
+ .get = s3c2416_cpufreq_get_speed,
+ .init = s3c2416_cpufreq_driver_init,
+ .name = "s3c2416",
+ .attr = s3c2416_cpufreq_attr,
+};
+
+static int __init s3c2416_cpufreq_init(void)
+{
+ return cpufreq_register_driver(&s3c2416_cpufreq_driver);
+}
+module_init(s3c2416_cpufreq_init);
--
1.7.5.4
--
To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
