Re: microblaze HAVE_MEMBLOCK_NODE_MAP dependency (was Re: [PATCH v2 0/5] mm: Enable CONFIG_NODES_SPAN_OTHER_NODES by default for NUMA)

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, Sep 02, 2019 at 03:51:25PM +0200, Michal Simek wrote:
> On 31. 07. 19 19:15, Mike Rapoport wrote:
> > On Wed, Jul 31, 2019 at 04:41:14PM +0200, Michal Hocko wrote:
> >> On Wed 31-07-19 17:21:29, Mike Rapoport wrote:
> >>> On Wed, Jul 31, 2019 at 03:00:37PM +0200, Michal Hocko wrote:
> >>>>
> >>>> I am sorry, but I still do not follow. Who is consuming that node id
> >>>> information when NUMA=n. In other words why cannot we simply do
> >>>  
> >>> We can, I think nobody cared to change it.
> >>
> >> It would be great if somebody with the actual HW could try it out.
> >> I can throw a patch but I do not even have a cross compiler in my
> >> toolbox.
> > 
> > Well, it compiles :)
> >  
> >>>> diff --git a/arch/microblaze/mm/init.c b/arch/microblaze/mm/init.c
> >>>> index a015a951c8b7..3a47e8db8d1c 100644
> >>>> --- a/arch/microblaze/mm/init.c
> >>>> +++ b/arch/microblaze/mm/init.c
> >>>> @@ -175,14 +175,9 @@ void __init setup_memory(void)
> >>>>  
> >>>>  		start_pfn = memblock_region_memory_base_pfn(reg);
> >>>>  		end_pfn = memblock_region_memory_end_pfn(reg);
> >>>> -		memblock_set_node(start_pfn << PAGE_SHIFT,
> >>>> -				  (end_pfn - start_pfn) << PAGE_SHIFT,
> >>>> -				  &memblock.memory, 0);
> >>>> +		memory_present(0, start_pfn << PAGE_SHIFT, end_pfn << PAGE_SHIFT);
> >>>
> >>> memory_present() expects pfns, the shift is not needed.
> >>
> >> Right.
> 
> Sorry for slow response on this. In general regarding this topic.
> Microblaze is soft core CPU (now there are hardcore versions too but not
> running Linux). I believe there could be Numa system with
> microblaze/microblazes (SMP is not supported in mainline).
> 
> This code was added in 2011 which is pretty hard to remember why it was
> done in this way.
> 
> It compiles but not working on HW. Please take a look at log below.
> 
> Thanks,
> Michal
> 
> 
> [    0.000000] Linux version 5.3.0-rc6-00007-g54b01939182f-dirty
> (monstr@monstr-desktop3) (gcc version 8.2.0 (crosstool-NG 1.20.0)) #101
> Mon Sep 2 15:44:05 CEST 2019
> [    0.000000] setup_memory: max_mapnr: 0x40000
> [    0.000000] setup_memory: min_low_pfn: 0x80000
> [    0.000000] setup_memory: max_low_pfn: 0xb0000
> [    0.000000] setup_memory: max_pfn: 0xc0000
> [    0.000000] start pfn 0x80000
> [    0.000000] end pfn 0xc0000
> [    0.000000] Zone ranges:
> [    0.000000]   DMA      [mem 0x0000000080000000-0x00000000afffffff]
> [    0.000000]   Normal   empty
> [    0.000000]   HighMem  [mem 0x00000000b0000000-0x00000000bfffffff]
> [    0.000000] Movable zone start for each node
> [    0.000000] Early memory node ranges
> [    0.000000]   node   1: [mem 0x0000000080000000-0x00000000bfffffff]
> [    0.000000] Could not find start_pfn for node 0
> [    0.000000] Initmem setup node 0 [mem
> 0x0000000000000000-0x0000000000000000]

This does not look good :)

I think the problem is that without an explicit call to memblock_set_node()
the ->nid in memblock is MAX_NUMNODES but free_area_init_nodes() presumes
actual node ids are properly set.

> [    0.000000] earlycon: ns16550a0 at MMIO 0x44a01000 (options '115200n8')
> [    0.000000] printk: bootconsole [ns16550a0] enabled
> [    0.000000] setup_cpuinfo: initialising
> [    0.000000] setup_cpuinfo: Using full CPU PVR support
> [    0.000000] wt_msr_noirq
> [    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
> [    0.000000] pcpu-alloc: [0] 0
> [    0.000000] Built 1 zonelists, mobility grouping off.  Total pages: 0
> [    0.000000] Kernel command line: earlycon
> [    0.000000] Dentry cache hash table entries: -2147483648 (order: -13,
> 0 bytes, linear)
> [    0.000000] Inode-cache hash table entries: -2147483648 (order: -13,
> 0 bytes, linear)
> [    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
> [    0.000000] Oops: kernel access of bad area, sig: 11
> [    0.000000] CPU: 0 PID: 0 Comm: swapper Not tainted
> 5.3.0-rc6-00007-g54b01939182f-dirty #101
> [    0.000000]  Registers dump: mode=805B9EA8
> [    0.000000]  r1=000065A0, r2=C05B7AE6, r3=00000000, r4=00000000
> [    0.000000]  r5=00080000, r6=00080B50, r7=00000000, r8=00000004
> [    0.000000]  r9=00000000, r10=0000001F, r11=00000000, r12=00006666
> [    0.000000]  r13=4119DCC0, r14=00000000, r15=C05EFF8C, r16=00000000
> [    0.000000]  r17=C0604408, r18=FFFC0000, r19=C05B9F6C, r20=BFFEC168
> [    0.000000]  r21=BFFEC168, r22=EFFF9AC0, r23=00000001, r24=C0606874
> [    0.000000]  r25=BFE6B74C, r26=80000000, r27=00000000, r28=90000040
> [    0.000000]  r29=01000000, r30=00000380, r31=C05C02F0, rPC=C0604408
> [    0.000000]  msr=000046A0, ear=00000004, esr=00000D12, fsr=FFFFFFFF
> [    0.000000] Oops: kernel access of bad area, sig: 11
> 
> 
> -- 
> Michal Simek, Ing. (M.Eng), OpenPGP -> KeyID: FE3D1F91
> w: www.monstr.eu p: +42-0-721842854
> Maintainer of Linux kernel - Xilinx Microblaze
> Maintainer of Linux kernel - Xilinx Zynq ARM and ZynqMP ARM64 SoCs
> U-Boot custodian - Xilinx Microblaze/Zynq/ZynqMP/Versal SoCs
> 
> 




-- 
Sincerely yours,
Mike.




[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
[Index of Archives]     [Kernel Development]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite Info]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Linux Media]     [Device Mapper]

  Powered by Linux