Hello,
On 13/09/2022 00:37:53+0530, Jagath Jog J wrote:
> +static int max31329_get_osc_status(struct device *dev)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + unsigned int status;
> + int ret;
> +
> + ret = regmap_read(max31329->regmap, MAX31329_STATUS_REG, &status);
> + if (ret)
> + return ret;
> +
> + if (status & MAX31329_STATUS_OSF) {
> + dev_err(dev, "Oscillator has stopped\n");
I would drop this message there is probably nothing specific the user
can do once it appears in the kernel log.
> + return -EINVAL;
> + }
> + return 0;
> +}
> +
> +static int max31329_alarm_irq_enable(struct device *dev, unsigned int enable)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> +
> + return regmap_update_bits(max31329->regmap, MAX31329_INT_EN_REG,
> + MAX31329_INT_EN_A1IE,
> + enable ? MAX31329_INT_EN_A1IE : 0);
> +}
> +
> +static int max31329_read_alarm(struct device *dev, struct rtc_wkalrm *alarm)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + struct rtc_time *const tm = &alarm->time;
> + unsigned int aie_en, aie_flag;
> + int ret;
> + u8 regs[6];
> +
> + ret = max31329_get_osc_status(dev);
> + if (ret)
> + return ret;
> +
The oscillator being stopped doesn't mean the alarm is not correct so
you don't need to check here.
> + ret = regmap_bulk_read(max31329->regmap, MAX31329_ALM1_SEC_REG, regs,
> + MAX31329_ALM1_SEC_LEN);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(max31329->regmap, MAX31329_INT_EN_REG, &aie_en);
> + if (ret)
> + return ret;
> +
> + ret = regmap_read(max31329->regmap, MAX31329_STATUS_REG, &aie_flag);
> + if (ret)
> + return ret;
> +
> + tm->tm_sec = bcd2bin(regs[REG_TO_OFFSET(MAX31329_SECONDS_REG)] & 0x7f);
> + tm->tm_min = bcd2bin(regs[REG_TO_OFFSET(MAX31329_MINUTES_REG)] & 0x7f);
> + tm->tm_hour = bcd2bin(regs[REG_TO_OFFSET(MAX31329_HOURS_REG)] & 0x3f);
> + tm->tm_mday = bcd2bin(regs[REG_TO_OFFSET(MAX31329_DATE_REG) - 1] & 0x3f);
> + tm->tm_mon = bcd2bin(regs[REG_TO_OFFSET(MAX31329_MONTH_REG) - 1] &
> + 0x1f) - 1;
> + tm->tm_year = bcd2bin(regs[REG_TO_OFFSET(MAX31329_YEAR_REG) - 1]) + 200;
> +
> + alarm->enabled = FIELD_GET(MAX31329_INT_EN_A1IE, aie_en);
> + alarm->pending = FIELD_GET(MAX31329_STATUS_A1F, aie_flag) &&
> + alarm->enabled;
> +
> + return 0;
> +}
> +
> +static int max31329_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + const struct rtc_time *tm = &alrm->time;
> + u8 regs[6], year;
> + int ret;
> +
> + ret = max31329_get_osc_status(dev);
> + if (ret)
> + return ret;
It is fine to set the alarm while the oscillator is stopped. The usual
userspace tools will anyway prevent you from doing that because they
first read the time and that call will check.
> +
> + regs[REG_TO_OFFSET(MAX31329_SECONDS_REG)] = bin2bcd(tm->tm_sec) & 0x7F;
> + regs[REG_TO_OFFSET(MAX31329_MINUTES_REG)] = bin2bcd(tm->tm_min) & 0x7f;
> + regs[REG_TO_OFFSET(MAX31329_HOURS_REG)] = bin2bcd(tm->tm_hour) & 0x3f;
> + regs[REG_TO_OFFSET(MAX31329_DATE_REG) - 1] = bin2bcd(tm->tm_mday) & 0x3f;
> + regs[REG_TO_OFFSET(MAX31329_MONTH_REG) - 1] = bin2bcd(tm->tm_mon + 1) & 0x1f;
> +
> + if (tm->tm_year >= 200)
> + year = bin2bcd(tm->tm_year - 200);
> + else
> + year = bin2bcd(tm->tm_year - 100);
This doesn't feel right, doesn't that break start-year?
What is the actual time range supported by this RTC? Shouldn't you set
the century?
> + regs[REG_TO_OFFSET(MAX31329_YEAR_REG) - 1] = year;
> +
> + ret = regmap_bulk_write(max31329->regmap, MAX31329_ALM1_SEC_REG, regs,
> + MAX31329_ALM1_SEC_LEN);
> + if (ret)
> + return ret;
> +
> + return max31329_alarm_irq_enable(dev, alrm->enabled);
> +}
> +
> +static int max31329_read_time(struct device *dev, struct rtc_time *tm)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + u8 data[7], century = 0;
> + int ret;
> +
> + ret = max31329_get_osc_status(dev);
> + if (ret)
> + return ret;
> +
> + ret = regmap_bulk_read(max31329->regmap, MAX31329_SECONDS_REG, data,
> + sizeof(data));
> + if (ret)
> + return ret;
> +
> + tm->tm_sec = bcd2bin(data[REG_TO_OFFSET(MAX31329_SECONDS_REG)] & 0x7f);
> + tm->tm_min = bcd2bin(data[REG_TO_OFFSET(MAX31329_MINUTES_REG)] & 0x7f);
> + tm->tm_hour = bcd2bin(data[REG_TO_OFFSET(MAX31329_HOURS_REG)] & 0x3f);
> + /* Day of the week in linux range is 0~6 while 1~7 in RTC chip */
> + tm->tm_wday = bcd2bin(data[REG_TO_OFFSET(MAX31329_DAY_REG)] & 0x07) - 1;
> + tm->tm_mday = bcd2bin(data[REG_TO_OFFSET(MAX31329_DATE_REG)] & 0x3f);
> + /* linux tm_mon range:0~11, while month range is 1~12 in RTC chip */
> + tm->tm_mon = bcd2bin(data[REG_TO_OFFSET(MAX31329_MONTH_REG)] & 0x1f) - 1;
> +
> + century = data[REG_TO_OFFSET(MAX31329_MONTH_REG)] & MAX31329_MONTH_CENTURY;
> + tm->tm_year = bcd2bin(data[REG_TO_OFFSET(MAX31329_YEAR_REG)]) +
> + (century ? 200 : 100);
> +
> + return 0;
> +}
> +
> +static int max31329_set_time(struct device *dev, struct rtc_time *tm)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + u8 regs[7];
> + int ret;
> +
> + ret = max31329_get_osc_status(dev);
> + if (ret)
> + return ret;
> +
Checking the oscillator is not needed here but resetting the status is.
> + regs[REG_TO_OFFSET(MAX31329_SECONDS_REG)] = bin2bcd(tm->tm_sec);
> + regs[REG_TO_OFFSET(MAX31329_MINUTES_REG)] = bin2bcd(tm->tm_min);
> + regs[REG_TO_OFFSET(MAX31329_HOURS_REG)] = bin2bcd(tm->tm_hour);
> + regs[REG_TO_OFFSET(MAX31329_DAY_REG)] = bin2bcd(tm->tm_wday + 1);
> + regs[REG_TO_OFFSET(MAX31329_DATE_REG)] = bin2bcd(tm->tm_mday);
> + regs[REG_TO_OFFSET(MAX31329_MONTH_REG)] = bin2bcd(tm->tm_mon + 1);
> +
> + if (tm->tm_year >= 200)
> + regs[REG_TO_OFFSET(MAX31329_MONTH_REG)] |= MAX31329_MONTH_CENTURY;
> + regs[REG_TO_OFFSET(MAX31329_YEAR_REG)] = bin2bcd(tm->tm_year % 100);
> +
> + return regmap_bulk_write(max31329->regmap, MAX31329_SECONDS_REG, regs,
> + MAX31329_WATCH_SEC_LEN);
> +}
> +
> +static const struct rtc_class_ops max31329_rtc_ops = {
> + .read_time = max31329_read_time,
> + .set_time = max31329_set_time,
> + .read_alarm = max31329_read_alarm,
> + .set_alarm = max31329_set_alarm,
> + .alarm_irq_enable = max31329_alarm_irq_enable,
> +};
> +
> +static irqreturn_t max31329_irq_handler(int irq, void *dev_id)
> +{
> + struct device *dev = dev_id;
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + unsigned int flags, controls;
> + unsigned long events = 0;
> + int ret;
> +
> + ret = regmap_read(max31329->regmap, MAX31329_INT_EN_REG, &controls);
> + if (ret) {
> + dev_warn(dev, "Read IRQ control register error %d\n", ret);
Drop all of those messages please.
> + return IRQ_NONE;
> + }
> +
> + ret = regmap_read(max31329->regmap, MAX31329_STATUS_REG, &flags);
> + if (ret) {
> + dev_warn(dev, "Read IRQ flags register error %d\n", ret);
> + return IRQ_NONE;
> + }
> +
> + if (flags & MAX31329_STATUS_A1F) {
> + flags &= ~MAX31329_STATUS_A1F;
> + controls &= ~MAX31329_INT_EN_A1IE;
> + events = RTC_AF | RTC_IRQF;
> + }
> +
> + if (events) {
> + rtc_update_irq(max31329->rtc, 1, events);
> + regmap_write(max31329->regmap, MAX31329_STATUS_REG, flags);
> + regmap_write(max31329->regmap, MAX31329_INT_EN_REG, controls);
> + return IRQ_HANDLED;
> + }
> +
> + return IRQ_NONE;
> +}
> +
> +static void max31329_trickle_config(struct device *dev)
> +{
> + struct max31329_data *max31329 = dev_get_drvdata(dev);
> + u8 trickle_reg;
> + int ret, i;
> + u32 ohms;
> +
> + /* Configure the trickle charger. */
> + ret = device_property_read_u32(dev, "trickle-resistor-ohms", &ohms);
> + if (ret)
> + return;
> +
> + trickle_reg = MAX31329_TRICKLE_EN;
> + for (i = 1; i <= ARRAY_SIZE(max31329_trickle_ohms); i++) {
> + if (max31329_trickle_ohms[i - 1] == ohms) {
> + trickle_reg |= i;
> + regmap_write(max31329->regmap, MAX31329_TRICKLE_REG,
> + trickle_reg);
> + }
> + }
> +}
> +
> +static int max31329_nvram_write(void *priv, unsigned int offset, void *val,
> + size_t bytes)
> +{
> + struct regmap *max31329_regmap = (struct regmap *)priv;
> +
> + return regmap_bulk_write(max31329_regmap,
> + MAX31329_RAM0_START_REG + offset,
> + val, bytes);
> +}
> +
> +static int max31329_nvram_read(void *priv, unsigned int offset, void *val,
> + size_t bytes)
> +{
> + struct regmap *max31329_regmap = (struct regmap *)priv;
> +
> + return regmap_bulk_read(max31329_regmap,
> + MAX31329_RAM0_START_REG + offset,
> + val, bytes);
> +}
> +
> +#ifdef CONFIG_COMMON_CLK
> +#define clkout_hw_to_max31329(hw) container_of(hw, struct max31329_data, clkout_hw)
> +
> +static int clkout_rates[] = {
> + 1,
> + 4096,
> + 8192,
> + 32768
> +};
> +
> +static unsigned long max31329_clkout_recalc_rate(struct clk_hw *hw,
> + unsigned long parent_rate)
> +{
> + struct max31329_data *max31329 = clkout_hw_to_max31329(hw);
> + int clkout, ret;
> +
> + ret = regmap_read(max31329->regmap, MAX31329_RTC_CONFIG2_REG, &clkout);
> + if (ret)
> + return 0;
> +
> + return clkout_rates[FIELD_GET(MAX31329_RTC_CFG2_CLKOHZ_MSK, clkout)];
> +}
> +
> +static long max31329_clkout_round_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long *prate)
> +{
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(clkout_rates); i++)
> + if (clkout_rates[i] >= rate)
> + return clkout_rates[i];
> +
> + return 0;
> +}
> +
> +static int max31329_clkout_set_rate(struct clk_hw *hw, unsigned long rate,
> + unsigned long parent_rate)
> +{
> + struct max31329_data *max31329 = clkout_hw_to_max31329(hw);
> + int i;
> +
> + for (i = 0; i < ARRAY_SIZE(clkout_rates); i++)
> + if (rate == clkout_rates[i])
> + return regmap_update_bits(max31329->regmap,
> + MAX31329_RTC_CONFIG2_REG,
> + MAX31329_RTC_CFG2_CLKOHZ_MSK,
> + FIELD_PREP(MAX31329_RTC_CFG2_CLKOHZ_MSK,
> + i));
> + return -EINVAL;
> +}
> +
> +static int max31329_clkout_prepare(struct clk_hw *hw)
> +{
> + struct max31329_data *max31329 = clkout_hw_to_max31329(hw);
> +
> + return regmap_update_bits(max31329->regmap, MAX31329_RTC_CONFIG2_REG,
> + MAX31329_RTC_CONFIG2_ENCLKO,
> + MAX31329_RTC_CONFIG2_ENCLKO);
> +}
> +
> +static void max31329_clkout_unprepare(struct clk_hw *hw)
> +{
> + struct max31329_data *max31329 = clkout_hw_to_max31329(hw);
> +
> + regmap_update_bits(max31329->regmap, MAX31329_RTC_CONFIG2_REG,
> + MAX31329_RTC_CONFIG2_ENCLKO,
> + FIELD_PREP(MAX31329_RTC_CONFIG2_ENCLKO, 0));
> +}
> +
> +static int max31329_clkout_is_prepared(struct clk_hw *hw)
> +{
> + struct max31329_data *max31329 = clkout_hw_to_max31329(hw);
> + int clkout, ret;
> +
> + ret = regmap_read(max31329->regmap, MAX31329_RTC_CONFIG2_REG, &clkout);
> + if (ret)
> + return ret;
> +
> + return !!(clkout & MAX31329_RTC_CONFIG2_ENCLKO);
> +}
> +
> +static const struct clk_ops max31329_clkout_ops = {
> + .prepare = max31329_clkout_prepare,
> + .unprepare = max31329_clkout_unprepare,
> + .is_prepared = max31329_clkout_is_prepared,
> + .recalc_rate = max31329_clkout_recalc_rate,
> + .round_rate = max31329_clkout_round_rate,
> + .set_rate = max31329_clkout_set_rate,
> +};
> +
> +static int max31329_clkout_register_clk(struct max31329_data *max31329,
> + struct i2c_client *client)
> +{
> + struct device_node *node = client->dev.of_node;
> + struct clk_init_data init;
> + struct clk *clk;
> +
> + init.name = "max31329-clkout";
> + init.ops = &max31329_clkout_ops;
> + init.flags = 0;
> + init.parent_names = NULL;
> + init.num_parents = 0;
> + max31329->clkout_hw.init = &init;
> +
> + /* optional override of the clockname */
> + of_property_read_string(node, "clock-output-names", &init.name);
> +
> + clk = devm_clk_register(&client->dev, &max31329->clkout_hw);
> + if (!IS_ERR(clk))
> + of_clk_add_provider(node, of_clk_src_simple_get, clk);
> +
> + return PTR_ERR(clk);
> +}
> +#endif
> +
> +static int max31329_probe(struct i2c_client *client,
> + const struct i2c_device_id *id)
> +{
> + struct max31329_data *max31329;
> + int ret;
> + struct nvmem_config nvmem_cfg = {
> + .name = "max31329_nvram",
> + .word_size = 1,
> + .stride = 1,
> + .size = 64,
> + .type = NVMEM_TYPE_BATTERY_BACKED,
> + .reg_read = max31329_nvram_read,
> + .reg_write = max31329_nvram_write,
> + };
> +
> + max31329 = devm_kzalloc(&client->dev, sizeof(*max31329), GFP_KERNEL);
> + if (!max31329)
> + return -ENOMEM;
> +
> + max31329->regmap = devm_regmap_init_i2c(client, &config);
> + if (IS_ERR(max31329->regmap)) {
> + dev_err(&client->dev, "regmap init failed\n");
> + return PTR_ERR(max31329->regmap);
> + }
> +
> + dev_set_drvdata(&client->dev, max31329);
> +
> + max31329->rtc = devm_rtc_allocate_device(&client->dev);
> + if (IS_ERR(max31329->rtc))
> + return PTR_ERR(max31329->rtc);
> +
> + max31329->rtc->ops = &max31329_rtc_ops;
> + max31329->irq = client->irq;
> + max31329->rtc->range_min = RTC_TIMESTAMP_BEGIN_2000;
> + max31329->rtc->range_max = RTC_TIMESTAMP_END_2199;
> +
> + if (max31329->irq) {
> + ret = devm_request_threaded_irq(&client->dev, max31329->irq,
> + NULL, max31329_irq_handler,
> + IRQF_TRIGGER_LOW | IRQF_ONESHOT,
> + "max31329", &client->dev);
> + if (ret) {
> + dev_err(&client->dev, "unable to request IRQ\n");
This message can be dropped.
> + return ret;
> + }
> +
> + ret = regmap_write(max31329->regmap, MAX31329_RTC_CONFIG2_REG,
> + MAX31329_RTC_CONFIG2_ENCLKO);
Can you explain what this does because if you are changing a default
register value, we will be stuck with that forever and I feel like this
is something that should be configurable.
> + if (ret) {
> + dev_err(&client->dev, "unable to configure INT pin");
> + return ret;
> + }
> +
> + if (device_property_read_bool(&client->dev, "wakeup-source"))
> + device_init_wakeup(&client->dev, true);
wakeup-source should be used when no interrupt is available. When there
is a interrupt, we assume the RTC can wake up the device.
> + } else {
> + clear_bit(RTC_FEATURE_ALARM, max31329->rtc->features);
> + clear_bit(RTC_FEATURE_UPDATE_INTERRUPT, max31329->rtc->features);
> + }
> +
> + ret = devm_rtc_register_device(max31329->rtc);
> + if (ret)
> + return ret;
> +
> + max31329_trickle_config(&client->dev);
> +
> + nvmem_cfg.priv = max31329->regmap;
> + devm_rtc_nvmem_register(max31329->rtc, &nvmem_cfg);
> +
> +#ifdef CONFIG_COMMON_CLK
> + max31329_clkout_register_clk(max31329, client);
> +#endif
> +
> + return 0;
> +}
> +
> +static const __maybe_unused struct of_device_id max31329_of_match[] = {
> + { .compatible = "maxim,max31329", },
> + { }
> +};
> +MODULE_DEVICE_TABLE(of, max31329_of_match);
> +
> +static struct i2c_driver max31329_driver = {
> + .driver = {
> + .name = "rtc-max31329",
> + .of_match_table = of_match_ptr(max31329_of_match),
> + },
> + .probe = max31329_probe,
> +};
> +module_i2c_driver(max31329_driver);
> +
> +MODULE_AUTHOR("Jagath Jog J <jagathjog1996@xxxxxxxxx>");
> +MODULE_DESCRIPTION("Maxim MAX31329 RTC driver");
> +MODULE_LICENSE("GPL");
> --
> 2.17.1
>
--
Alexandre Belloni, co-owner and COO, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com
