Steven Rostedt wrote:
On Tue, 1 Jul 2008, Wolfgang Grandegger wrote:
I continue this thread because it's still not understood why enabling
CONFIG_RCU_TRACE is necessary to get reasonable latencies on the
MPC5200. It might also explain, why I get much worse latencies with
2.6.25.8-rt7.
Have you tried turning on ftrace?
Not yet.
To recapitulate, with CONFIG_RCU_TRACE enabled, cyclictest reports max.
latencies of approx. 130 us with 2.6.24.4-rt4 on my MPC5200 PowerPC
board. If I disable it, the latency goes up to 600 us. Obviously, the
trace_mark() calls in rcupreempt*.c have some positive impact on the
latency. I narrowed down, that the 2 calls in __rcu_preempt_boost() in
rcupreempt-boost.c are the important one:
void __rcu_preempt_unboost(void)
{
struct task_struct *curr = current;
struct rcu_boost_dat *rbd;
int prio;
unsigned long flags;
trace_mark(unboost_called, "NULL");
To make it clear: If I just comment out the line above and ...
/* if not boosted, then ignore */
if (likely(!rcu_is_boosted(curr)))
return;
I wonder if the "likely" is faulty on the PPC code generation. Have you
tried removing that "likely" statement.
/*
* Need to be very careful with NMIs.
* If we take the lock and an NMI comes in
* and it may try to unboost us if curr->rcub_rbdp
* is still set. So we zero it before grabbing the lock.
* But this also means that we might be boosted again
* so the boosting code needs to be aware of this.
*/
rbd = curr->rcub_rbdp;
curr->rcub_rbdp = NULL;
/*
* Now an NMI might have came in after we grab
* the below lock. This check makes sure that
* the NMI doesn't try grabbing the lock
* while we already have it.
*/
if (unlikely(!rbd))
return;
Actually, remove all "likely" and "unlikely". The marker code could be
making it work better. But still, this shouldn't cause 600us latencies.
spin_lock_irqsave(&rbd->rbs_lock, flags);
/*
* It is still possible that an NMI came in
* between the "is_boosted" check and setting
* the rcu_rbdp to NULL. This would mean that
* the NMI already dequeued us.
*/
if (unlikely(!rcu_is_boosted(curr)))
goto out;
list_del_init(&curr->rcub_entry);
trace_mark(unboosted, "NULL");
.. this one as well, then the latency goes *up* to 600us. The first one
has more influence, though.
curr->rcu_prio = MAX_PRIO;
spin_lock(&curr->pi_lock);
prio = rt_mutex_getprio(curr);
task_setprio(curr, prio);
curr->rcub_rbdp = NULL;
spin_unlock(&curr->pi_lock);
out:
spin_unlock_irqrestore(&rbd->rbs_lock, flags);
}
With them and all other trace_mark() calls commented out, the latency is
still OK. The first one has a bigger impact.
In 2.6.25.8-rt7, trace_mark() is not used any more but a function
incrementing the corresponding counter directly and I suspect that's the
reason why I'm seeing high latencies with both, CONFIG_RCU_TRACE enabled
and disabled.
I hope this observation sheds some light on the issue.
It is still a mystery to me. Maybe looking at the different assembly
outputs with the different configurations.
There seems to be something in trace_mark() keeping latency low:
http://lxr.linux.no/linux+v2.6.24.4/include/linux/marker.h#L52
I will follow your suggestions.
Wolfgang.
--
To unsubscribe from this list: send the line "unsubscribe linux-rt-users" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
