Hi David,
Am Samstag, 22. September 2018, 19:02:36 CEST schrieb David Summers:
> Now as fair as I understand. the asus tinker board contains a wifi
> So should this patch be added to the tinker board dtsi ?
>
> It also far move complex - it adds far more things, so consider
>
> Signed-off-by: David Summers <beagleboard@xxxxxxxxxxxxxxxxxxx>
> ---
> arch/arm/boot/dts/rk3288-tinker-s.dts | 93 +++++++++++++++++++++++++++
> 1 file changed, 93 insertions(+)
>
> diff --git a/arch/arm/boot/dts/rk3288-tinker-s.dts b/arch/arm/boot/dts/rk3288-tinker-s.dts
> index bc691e3f9c07..3d91924fd8db 100644
> --- a/arch/arm/boot/dts/rk3288-tinker-s.dts
> +++ b/arch/arm/boot/dts/rk3288-tinker-s.dts
> @@ -10,6 +10,95 @@
> / {
> model = "Rockchip RK3288 Asus Tinker Board S";
> compatible = "asus,rk3288-tinker-s", "rockchip,rk3288";
> +
> + wireless-bluetooth {
> + compatible = "bluetooth-platdata";
> + uart_rts_gpios = <&gpio4 19 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default","rts_gpio";
> + pinctrl-0 = <&uart0_rts>;
> + pinctrl-1 = <&uart0_gpios>;
> + BT,reset_gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>;
> + BT,wake_gpio = <&gpio4 26 GPIO_ACTIVE_HIGH>;
> + BT,wake_host_irq = <&gpio4 31 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
the basic problem here is, that all these nodes stem from the so called
soc-vendor-tree. Devicetree bindings normally go through a review process
while soc vendors often invent their own shortcut that is not and will
not be supported by the mainline kernel.
Bluetooth-platdata and wlan-platdata are examples of that.
Additionally, the kernel now has the somewhat new "serdev" to manage the
needed connection between bluetooth and uart. See
http://events17.linuxfoundation.org/sites/events/files/slides/serdev-elce-2017-2.pdf
for an introduction.
> + wireless-wlan {
> + compatible = "wlan-platdata";
> + rockchip,grf = <&grf>;
> + wifi_chip_type = "ap6212";
> + sdio_vref = <1800>;
> + WIFI,host_wake_irq = <&gpio4 30 GPIO_ACTIVE_HIGH>;
> + status = "okay";
> + };
> +
> + io-domains {
> + compatible = "rockchip,rk3288-io-voltage-domain";
> + rockchip,grf = <&grf>;
> + flash0-supply = <&vcc_flash>;
> + gpio30-supply = <&vcc_io>;
> + wifi-supply = <&vcc_18>;
> + sdcard-supply = <&vccio_sd>;
> + };
io-domains node is already present in rk3288-tinker.dtsi, so please
add additional properties there (compatible + rockchip,grf are not needed)
> +
> + sdio_pwrseq: sdio-pwrseq {
> + compatible = "mmc-pwrseq-simple";
> + clocks = <&rk808 1>;
> + clock-names = "ext_clock";
> + pinctrl-names = "default";
> + pinctrl-0 = <&chip_enable_h>, <&wifi_enable_h>;
> +
> + /*
> + * On the module itself this is one of these (depending
> + * on the actual card populated):
> + * - SDIO_RESET_L_WL_REG_ON
> + * - PDN (power down when low)
> + */
> + reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>, <&gpio4 27 GPIO_ACTIVE_LOW>;
> + };
> +
> + vcc_flash: flash-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc_flash";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + vin-supply = <&vcc_io>;
> + };
that is a supply for the emmc - so not related to wifi at all, and I don't
think that is actually named that way in the device schematics. Please
use supply-names as described in the schematics pdf - I'd think Asus
should provide one for the dev-board somewhere.
> +};
> +
> +&pinctrl {
> + sdio-pwrseq {
> + wifi_enable_h: wifi-enable-h {
> + rockchip,pins = <4 28 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + chip_enable_h: chip-enable-h {
> + rockchip,pins = <4 27 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
> +
> + wireless-bluetooth {
> + uart0_gpios: uart0-gpios {
> + rockchip,pins = <4 19 RK_FUNC_GPIO &pcfg_pull_none>;
> + };
> + };
not needed
> +};
> +
> +&sdio0 {
> + status = "okay";
> + clock-frequency = <50000000>;
> + clock-freq-min-max = <200000 50000000>;
> + bus-width = <4>;
> + cap-sd-highspeed;
> + cap-sdio-irq;
> + disable-wp;
> + keep-power-in-suspend;
> + mmc-pwrseq = <&sdio_pwrseq>;
> + non-removable;
> + num-slots = <1>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&sdio0_bus4 &sdio0_cmd &sdio0_clk>;
> + sd-uhs-sdr104;
> + supports-sdio;
> };
>
> &emmc {
> @@ -25,3 +114,7 @@
> mmc-ddr-1_8v;
> status = "okay";
> };
> +
> +&uart0 {
> + pinctrl-0 = <&uart0_xfer>, <&uart0_cts>;
> +};
>
So ideally, take a look at other Rockchip boards on how they hook up wifi
and start small by checking what the &sdio part above actually needs to
function, then expand from there.
Heiko
_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/linux-rockchip
