The Renesas {EMMA mobile, RZ/V2M} UART compatible with the general-purpose
16750 UART chip. This patch updates Renesas {EMMA mobile, RZ/V2M} UART type
from 16550a->16750 and also enables 64-bytes fifo.
This patch series also simplifies 8250_em_probe() and also updates the
register handling for the below restriction mentioned in the hardware
manual.
40.6.1 Point for Caution when Changing the Register Settings:
When changing the settings of the following registers, a PRESETn master
reset or FIFO reset + SW reset (FCR[2],FCR[1], HCR0[7]) must be input to
re-initialize them.
Target Registers: FCR, LCR, MCR, DLL, DLM, HCR0.
v3->v4:
* Split patch#1 to 3 patches and removed Rb tags.
* Replaced dev_err->dev_err_probe() in probe()
* Added a local variable 'dev' to replace '&pdev->dev' in probe().
* Patch#2 removes unused header file slab.h.
* Patch#3 simplifies clk handling in probe()/remove()
* Removed sclk from struct serial8250_em_priv instead used local
variable in probe()
* Replaced devm_clk_get->devm_clk_get_enabled() and removed
clk_prepare_enable/clk_disable_unprepare from probe()/remove().
* Both {RZ/V2M, EMMA mobile} SoC is Register-compatible
with the general-purpose 16750 UART chip. So started using
generic compatible and removed struct serial8250_em_hw_info.
* Introduced pseudo offset for UART_FCR(UART_FCR_EM) and used
UART_FCR_EM in serial8250_em_serial{_in/_out} function to read/write
FCR register.
* Updated register update restriction to EMMA mobile SoC as well.
* Replaced readl->serial8250_em_serial_in() for reading fcr register
in serial8250_em_reg_update().
* Added serial8250_em_serial_out_helper() to simplify the
code and used for register writes in serial8250_em_reg_update().
v2->v3:
* Dropped sclk from priv.
* Dropped unneeded clk_disable_unprepare from remove().
* Retained Rb tags from Geert,Andy and Ilpo as the changes are trivial.
* Replaced of_device_get_match_data->device_get_match_data
* Dropped struct serial8250_em_hw_info *info from priv and started
using a local variable info in probe().
* Retained Rb tag from Ilpo as changes are trivial.
* Replaced readl/writel()->serial8250_em_serial_in/out() in serial8250_rzv2m_
reg_update() to avoid duplication of offset trickery.
* Added support for HCR0 read/write in serial8250_em_{serial_in, serial_out}
* Added UART_LCR macro support in serial8250_em_serial_in() to read LCR
* Reordered serial8250_em_{serial_in, serial_out} above serial8250_rzv2m_
reg_update().
* Replaced priv->info->serial_out to info->serial_out.
v1->v2:
* Dropped patch#1 from previous series
* Replaced devm_clk_get->devm_clk_get_enabled() and updated clk
handling in probe().
* Added Rb tag from Geert.
* Added patch for updating Renesas RZ/V2M UART type from 16550a->16750
and also enables 64-bytes fifo.
* Used .data for taking h/w differences between EMMA mobile and RZ/V2M UART.
* Added serial_out() to struct serial8250_em_hw_info for the write register
differences between EMMA mobile and RZ/V2M UART.
Biju Das (6):
serial: 8250_em: Use dev_err_probe()
serial: 8250_em: Drop slab.h
serial: 8250_em: Use devm_clk_get_enabled()
serial: 8250_em: Update port type as PORT_16750
serial: 8250_em: Use pseudo offset for UART_FCR
serial: 8250_em: Add serial8250_em_{reg_update(),out_helper()}
drivers/tty/serial/8250/8250_em.c | 110 +++++++++++++++++++++++-------
1 file changed, 85 insertions(+), 25 deletions(-)
--
2.25.1
