RE: [PATCH v6 1/7] dt-bindings: usb: hd3ss3220 device tree binding document

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Biju-san,

Thank you for the patch!

> From: Biju Das, Sent: Wednesday, May 15, 2019 9:09 PM
> 
> Add device tree binding document for TI HD3SS3220 Type-C DRP port
> controller driver.
> 
> Signed-off-by: Biju Das <biju.das@xxxxxxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> V5-->V6
>   * No change.
> V4-->V5
>   * No Change.
> V3-->V4
>   * No Change.
> V2-->V3
>   * Added Rob's Reviewed by tag.
> V1-->V2
>   * Added connector node.
>   * updated the example with connector node.
> ---
>  .../devicetree/bindings/usb/ti,hd3ss3220.txt       | 37 ++++++++++++++++++++++
>  1 file changed, 37 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt
> 
> diff --git a/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt
> b/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt
> new file mode 100644
> index 0000000..7f41400
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/ti,hd3ss3220.txt
> @@ -0,0 +1,37 @@
> +TI HD3SS3220 TypeC DRP Port Controller.
> +
> +Required properties:
> + - compatible: Must be "ti,hd3ss3220".
> + - reg: I2C slave address, must be 0x47 or 0x67 based on ADDR pin.
> + - interrupts: <a b> where a is the interrupt number and b represents an
> +   encoding of the sense and level information for the interrupt.
> +
> +Required sub-node:
> + - connector : The "usb-c-connector" attached to the hd3ss3220 chip. The

s/connector :/connector:/

> +   bindings of the connector node are specified in:
> +
> +	Documentation/devicetree/bindings/connector/usb-connector.txt
> +
> +Example:
> +hd3ss3220@47 {
> +	compatible = "ti,hd3ss3220";
> +	reg = <0x47>;
> +	interrupt-parent = <&gpio6>;
> +	interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +
> +	usb_con: connector {
> +		compatible = "usb-c-connector";
> +		label = "USB-C";
> +		data-role = "dual";
> +	};
> +
> +	port {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		hd3ss3220_ep: endpoint@0 {
> +			reg = <0>;
> +			remote-endpoint = <&usb3peri_role_switch>;
> +		};
> +	};

According to the connector/usb-connector.txt, should the connector node
have ports, port@1 and an endpoint nodes like below?

	usb_con: connector {
		compatible = "usb-c-connector";
		label = "USB-C";
		data-role = "dual";

		ports {
			#address-cells = <1>;
			#size-cells = <0>;

			port@1 {
				reg = <1>;
				hd3ss3220_ep: endpoint {
					remote-endpoint = <&usb3peri_role_switch>;
				};
			};
		};
	};

Best regards,
Yoshihiro Shimoda





[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux