Hi Niklas,
A few more talk on the adv748x link handling, please bear with me...
On Sat, Aug 25, 2018 at 03:18:06PM +0200, jacopo mondi wrote:
> Hi Laurent, Niklas,
>
> On Sat, Aug 25, 2018 at 08:37:15AM +0200, Niklas Söderlund wrote:
> > Hi Laurent and Jacopo,
> >
> > On 2018-08-25 02:54:44 +0300, Laurent Pinchart wrote:
> > > Hi Jacopo,
> > >
> > > On Monday, 20 August 2018 13:16:34 EEST Jacopo Mondi wrote:
> > > > Hello renesas list,
> > > > this series add supports for the HDMI and CVBS input to R-Car E3 R8A77990
> > > > Ebisu board.
> > > >
> > > > It's an RFT, as I don't have an Ebisu to test with :(
> > > >
> > > > The series adds supports for the following items:
> > > >
> > > > - PFC: add VIN groups and functions
> > > > - R-Car VIN and R-Car CSI-2: add support for R8A77990
> > > > - R8A77990: Add I2C, VIN and CSI-2 nodes
> > > > - Ebisu: describe HDMI and CVBS inputs
> > > >
> > > > Each patch, when relevant reports difference between the upported BSP patch
> > > > and the proposed one.
> > > >
> > > > I know Laurent should receive an Ebisu sooner or later, maybe we can sync
> > > > for testing :)
> > >
> > > I've given the series a first test, and I think a bit more work is needed :-)
> > >
> > > [ 1.455533] adv748x 0-0070: Endpoint /soc/i2c@e6500000/video-receiver@70/
> > > port@7/endpoint on port 7
> > > [ 1.464683] adv748x 0-0070: Endpoint /soc/i2c@e6500000/video-receiver@70/
> > > port@8/endpoint on port 8
> > > [ 1.473728] adv748x 0-0070: Endpoint /soc/i2c@e6500000/video-receiver@70/
> > > port@a/endpoint on port 10
> > > [ 1.484835] adv748x 0-0070: chip found @ 0xe0 revision 2143
> > > [ 1.639470] adv748x 0-0070: No endpoint found for txb
> > > [ 1.644653] adv748x 0-0070: Failed to probe TXB
> >
> > I fear this is a design choice in the adv748x driver. Currently the
> > driver requires both of its two CSI-2 transmitters to be connected/used
> > else probe fails. Furthermore the HDMI capture is always routed to TXA
> > while the analog capture is always routed to TXB.
> >
> > Now that we have a board where only TXA is connected but both HDMI and
> > analog captures are used maybe it's time to do some more work on v4l2
> > and the adv748x driver ;-P What's missing:
> >
> > - Probe should be OK with either TXA or TXB connected and not bail if
> > not both are used.
>
> I have three patches for this I hope to share as soon as I'll be able
> to do some more testing
>
> > - The media_device_ops or at least the .link_notify() callback of that
> > struct must be changed so not one driver in the media graph is
> > responsible for all links. In this case rcar-vin provides the callback
> > and rcar-vin should not judge which links between the adv748x
> > subdevices are OK to enable/disable. Currently the links between the
> > adv748x subdevices are immutably enabled to avoid this particular
> > problem.
>
> Uh, I didn't get this :/ Care to elaborate more?
>
I'm thinking if it is not enough to just provide a .link_setup()
callback to the (enabled) csi-2 sink pads of the adv748x and handle
routing between the afe/hdmi sources and that sink, without the vin's
registered link_notify playing any role in that.
> What I was about to do, instead, given the fixed HDMI->TXA and AFE->TXB
> routing in the adv748x driver was to insert a .link_validate() callback for
> both the HDMI and AFE backends, that checks for the availability of
> the corresponding output endpoint. This seems to me that this makes
> easy when dynamic routing will be added to do the same on the
> dynamically configured sink pad.
> What do you think?
On a second thought if a CSI-2 sink it's not enabled it is not part of
the media graph neither, so it should not be possible to link it in any
pipeline, so no link validation is required. The link simply can't
exist.
It seems to me that to support Ebisu-like designs is then enough to
make the adv748x driver probe with a single csi-2 output enabled and
handle power management accordingly. I will share patches for this
briefly.
>
> Thanks
> j
>
> >
> > >
> > > > PS: the list of upported patches will be sent separately.
> > > >
> > > > Jacopo Mondi (5):
> > > > media: dt-bindings: media: rcar-vin: Add R8A77990 support
> > > > media: rcar-vin: Add support for R-Car R8A77990
> > > > dt-bindings: media: rcar-csi2: Add R8A77990
> > > > media: rcar-csi2: Add R8A77990 support
> > > > arm64: dts: renesas: ebisu: Add HDMI and CVBS input
> > > >
> > > > Koji Matsuoka (1):
> > > > arm64: dts: r8a77990: Add VIN and CSI-2 device nodes
> > > >
> > > > Takeshi Kihara (2):
> > > > pinctrl: sh-pfc: r8a77990: Add VIN pins, groups and functions
> > > > arm64: dts: r8a77990: Add I2C device nodes
> > > >
> > > > .../devicetree/bindings/media/rcar_vin.txt | 1 +
> > > > .../bindings/media/renesas,rcar-csi2.txt | 1 +
> > > > arch/arm64/boot/dts/renesas/r8a77990-ebisu.dts | 86 ++++
> > > > arch/arm64/boot/dts/renesas/r8a77990.dtsi | 202 +++++++++
> > > > drivers/media/platform/rcar-vin/rcar-core.c | 20 +
> > > > drivers/media/platform/rcar-vin/rcar-csi2.c | 9 +
> > > > drivers/pinctrl/sh-pfc/pfc-r8a77990.c | 504 ++++++++++++++++++
> > > > 7 files changed, 823 insertions(+)
> > >
> > > --
> > > Regards,
> > >
> > > Laurent Pinchart
> > >
> > >
> > >
> >
> > --
> > Regards,
> > Niklas Söderlund
Attachment:
signature.asc
Description: PGP signature
