Hi Gilad,
On Thu, May 17, 2018 at 10:01 AM, Gilad Ben-Yossef <gilad@xxxxxxxxxxxxx> wrote:
> On Wed, May 16, 2018 at 10:43 AM, Simon Horman <horms@xxxxxxxxxxxx> wrote:
>> On Tue, May 15, 2018 at 04:50:44PM +0200, Geert Uytterhoeven wrote:
>>> On Tue, May 15, 2018 at 2:29 PM, Gilad Ben-Yossef <gilad@xxxxxxxxxxxxx> wrote:
>>> > Add bindings for CryptoCell instance in the SoC.
>>> >
>>> > Signed-off-by: Gilad Ben-Yossef <gilad@xxxxxxxxxxxxx>
>>>
>>> Thanks for your patch!
>>>
>>> > --- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
>>> > +++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
>>> > @@ -528,6 +528,14 @@
>>> > status = "disabled";
>>> > };
>>> >
>>> > + arm_cc630p: crypto@e6601000 {
>>> > + compatible = "arm,cryptocell-630p-ree";
>>> > + interrupts = <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH>;
>>> > + #interrupt-cells = <2>;
>>>
>>> I believe the #interrupt-cells property is not needed.
>>>
>>> > + reg = <0x0 0xe6601000 0 0x1000>;
>>> > + clocks = <&cpg CPG_MOD 229>;
Missing "power-domains = <&sysc R8A7795_PD_ALWAYS_ON>;", as
the Secure Engine is part of the CPG/MSSR clock domain (see below [*]).
>>> > + };
>>>
>>> The rest looks good, but I cannot verify the register block.
>>>
>>> > +
>>> > i2c3: i2c@e66d0000 {
>>> > #address-cells = <1>;
>>> > #size-cells = <0>;
>>
>> Thanks, I have applied this after dropping the #interrupt-cells property.
>
> Thanks you!
>
> Alas, it will not work without the clk patch (the previous one in the
> series) so they need to be
> taken or dropped together.
Indeed. From a quick glance, it looks like drivers/crypto/ccree/cc_driver.c
does not distinguish between the absence of the clock property, and an
actual error in getting the clock, and never considers any error a failure
(incl. -PROBE_DEFER).
As of_clk_get() returns -ENOENT for both a missing clock property and a
missing clock, you should use (devm_)clk_get() instead, and distinguish
between NULL (no clock property) and IS_ERR() (actual failure -> abort).
Hence in the absence of the clock patch, the driver accesses the crypto
engine while its module clock is turned off, leading to:
ccree e6601000.crypto: Invalid CC signature: SIGNATURE=0x00000000
!= expected=0xDCC63000
You must be lucky, though, usually you get an imprecise external abort
later, crashing the whole system ;-)
So I think this patch should be dropped for now.
However, even with your clock patch, the signature checking fails for me,
on both R-Car H3 ES1.0 and ES2.0.
Does this need changes to the ARM Trusted Firmware, to allow Linux to
access the public SCEG module?
[*] More on the subject of clock control:
At least for Renesas SoCs, where the module is part of a clock domain, and
can be controlled automatically by Runtime PM, you could drop the explicit
clock control, and use Runtime PM instead
(pm_runtime_{enable,get_sync,put,disable}()). That would allow the driver
to work on systems with any kind of PM Domains, too.
Depending on the other platforms that include a CryptoCell and their
(non)reliance on PM Domains, you may have to keep the explicit clock
handling, in addition to Runtime PM.
To decrease power consumption, I suggest to move the clock and/or Runtime
PM handling to the routines that actually use the hardware, instead of
powering the module in the probe routine.
Thanks!
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
