Re: [PATCH v14 2/2] rcar-csi2: add Renesas R-Car MIPI CSI-2 receiver driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Laurent,

On 2018-04-28 19:01:37 +0300, Laurent Pinchart wrote:
> Hi Niklas,
> 
> On Friday, 27 April 2018 02:28:32 EEST Niklas Söderlund wrote:
> > On 2018-04-27 00:30:25 +0300, Laurent Pinchart wrote:
> > > On Thursday, 26 April 2018 23:21:21 EEST Niklas Söderlund wrote:
> > >> A V4L2 driver for Renesas R-Car MIPI CSI-2 receiver. The driver
> > >> supports the R-Car Gen3 SoCs where separate CSI-2 hardware blocks are
> > >> connected between the video sources and the video grabbers (VIN).
> > >> 
> > >> Driver is based on a prototype by Koji Matsuoka in the Renesas BSP.
> > >> 
> > >> Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> > >> Reviewed-by: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> > >> Reviewed-by: Maxime Ripard <maxime.ripard@xxxxxxxxxxx>
> > >> Reviewed-by: Laurent Pinchart <laurent.pinchart@xxxxxxxxxxxxxxxx>
> > >> 
> > >> ---
> > >> 
> > >> * Changes since v13
> > >> - Change return rcar_csi2_formats + i to return &rcar_csi2_formats[i].
> > >> - Add define for PHCLM_STOPSTATECKL.
> > >> - Update spelling in comments.
> > >> - Update calculation in rcar_csi2_calc_phypll() according to
> > >>   https://linuxtv.org/downloads/v4l-dvb-apis/kapi/csi2.html. The one
> > >>   before v14 did not take into account that 2 bits per sample is
> > >>   transmitted.
> > > 
> > > Just one small comment about this, please see below.
> > > 
> > >> - Use Geert's suggestion of (1 << priv->lanes) - 1 instead of switch
> > >>   statement to set correct number of lanes to enable.
> > >> - Change hex constants in hsfreqrange_m3w_h3es1[] to lower case to match
> > >>   style of rest of file.
> > >> - Switch to %u instead of 0x%x when printing bus type.
> > >> - Switch to %u instead of %d for priv->lanes which is unsigned.
> > >> - Add MEDIA_BUS_FMT_YUYV8_1X16 to the list of supported formats in
> > >>   rcar_csi2_formats[].
> > >> - Fixed bps for MEDIA_BUS_FMT_YUYV10_2X10 to 20 and not 16.
> > >> - Set INTSTATE after PL-11 is confirmed to match flow chart in
> > >>   datasheet.
> > >> - Change priv->notifier.subdevs == NULL to !priv->notifier.subdevs.
> > >> - Add Maxime's and laurent's tags.
> > >> ---
> > >> 
> > >>  drivers/media/platform/rcar-vin/Kconfig     |  12 +
> > >>  drivers/media/platform/rcar-vin/Makefile    |   1 +
> > >>  drivers/media/platform/rcar-vin/rcar-csi2.c | 883 ++++++++++++++++++++
> > >>  3 files changed, 896 insertions(+)
> > >>  create mode 100644 drivers/media/platform/rcar-vin/rcar-csi2.c
> > > 
> > > [snip]
> > > 
> > >> diff --git a/drivers/media/platform/rcar-vin/rcar-csi2.c
> > >> b/drivers/media/platform/rcar-vin/rcar-csi2.c new file mode 100644
> > >> index 0000000000000000..49b29d5680f9d80b
> > >> --- /dev/null
> > > > +++ b/drivers/media/platform/rcar-vin/rcar-csi2.c
> > > 
> > > [snip]
> > > 
> > >> +static int rcar_csi2_calc_phypll(struct rcar_csi2 *priv, unsigned int
> > >> bpp,
> > >> +				 u32 *phypll)
> > >> +{
> > >> +	const struct phypll_hsfreqrange *hsfreq;
> > >> +	struct v4l2_subdev *source;
> > >> +	struct v4l2_ctrl *ctrl;
> > >> +	u64 mbps;
> > >> +
> > >> +	if (!priv->remote)
> > >> +		return -ENODEV;
> > >> +
> > >> +	source = priv->remote;
> > >> +
> > >> +	/* Read the pixel rate control from remote */
> > >> +	ctrl = v4l2_ctrl_find(source->ctrl_handler, V4L2_CID_PIXEL_RATE);
> > >> +	if (!ctrl) {
> > >> +		dev_err(priv->dev, "no pixel rate control in subdev %s\n",
> > >> +			source->name);
> > >> +		return -EINVAL;
> > >> +	}
> > >> +
> > >> +	/*
> > >> +	 * Calculate the phypll in mbps (from v4l2 documentation)
> > >> +	 * link_freq = (pixel_rate * bits_per_sample) / (2 * nr_of_lanes)
> > >> +	 */
> > >> +	mbps = v4l2_ctrl_g_ctrl_int64(ctrl) * bpp;
> > >> +	do_div(mbps, priv->lanes * 2000000);
> > > 
> > > pixel rate * bits per sample will give you the overall bit rate, which you
> > > then divide by the number of lanes to get the bitrate per lane, and then
> > > by 2 as D-PHY is a DDR PHY and transmits 2 bits per clock cycle. You then
> > > end up with the link frequency, which is thus expressed in MHz, not in
> > > Mbps. I would thus name the mbps variable freq, and rename the
> > > phypll_hsfreqrange mbps field to freq (maybe with a small comment right
> > > after the field to tell the value is expressed in MHz).
> > 
> > I agree that freq would be a better name for what it represents. Never
> > the less I prefer to stick with mbps as that is whats used in the
> > datasheet. See Table '25.9 HSFREQRANGE Bit Set Values'.
> > 
> > With this in mind if you still feel strongly about renaming it I could
> > do so. But at lest for me it feels more useful to easily be able to map
> > the variable to the datasheet tables :-)
> 
> After reading the datasheet I don't care too strongly about a rename, but I 
> now care about getting it right :-) The datasheet clearly specifies the 
> maximum data rate to be 1.5 Gbps / lane (section 25.1.1 Features), and figure 
> 25.9 corroborates that and shows a corresponding frequency of 750 MHz. I thus 
> believe that the values in table 25.9 and 25.10 are indeed bitrates (in Mbps / 
> lane), so I think you shouldn't divide by 2 in the above formula.

As this now appears to have been fully sorted out on the adv748x end I'm 
now in full agreement with you and I will not divide by 2 to get the 
bitrate here for the CSI-2 driver.

> 
> > >> +	for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++)
> > >> +		if (hsfreq->mbps >= mbps)
> > >> +			break;
> > >> +
> > >> +	if (!hsfreq->mbps) {
> > >> +		dev_err(priv->dev, "Unsupported PHY speed (%llu Mbps)", mbps);
> > >> +		return -ERANGE;
> > >> +	}
> > >> +
> > >> +	dev_dbg(priv->dev, "PHY HSFREQRANGE requested %llu got %u Mbps\n",
> > >> mbps,
> > >> +		hsfreq->mbps);
> > >> +
> > >> +	*phypll = PHYPLL_HSFREQRANGE(hsfreq->reg);
> > >> +
> > >> +	return 0;
> > >> +}
> > > 
> > > [snip]
> 
> -- 
> Regards,
> 
> Laurent Pinchart
> 
> 
> 

-- 
Regards,
Niklas Söderlund



[Index of Archives]     [Linux Samsung SOC]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux