Hi Olof, Hi Kevin, Hi Arnd, Please consider these Renesas ARM64 based SoC DT updates for v4.17. The following changes since commit 7928b2cbe55b2a410a0f5c1f154610059c57b1b2: Linux 4.16-rc1 (2018-02-11 15:04:29 -0800) are available in the git repository at: https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.17 for you to fetch changes up to ca565be2b526a731d02a2fbff96fb0572567ea55: arm64: dts: renesas: v3msk: add SCIF0 pins (2018-03-14 15:43:15 +0100) ---------------------------------------------------------------- Renesas ARM64 Based SoC DT Updates for v4.17 * R-Car Gen3 boards and SoCs - Make phy-mode of EtherAVB a board-specific property. The SoC DTs file now uses "rgmii" and boards override this with "rgmii-txid" as appropriate. Previously "rgmii-txid" was used in SoC DTs but this did not describe that more sophiticated functionality is a board rather than SoC property. * Condor board with R-Car V3H (r8a77980) SoC - Initial upstream support * Condor board with R-Car V3H (r8a77980) SoC - Initial upstream support * R-Car D3 (r8a77995) - Add I2C nodes and then describing the PCA9654 I/O expander connected to the I2C0 bus. * Eagle board with R-Car V3M (r8a77970) SoC - Enable PFC support for configuring SCIF0 pins This uses PFC support added to the V3M DT - Describe EtherAVB PHY IRQ This uses support for GPIO added to the V3M DT - Enable I2C0 support Sergei Shtylyov says "The I2C0 bus is populated by ON Semiconductor PCA9653 I/O expander and Analog Devices ADV7511W HDMI transmitter (but we're only describing the former chip now)." * R-Car V3M (r8a77970) SoCs - Add PFC support - Describe GPIO devices - Describe I2C devices - Srt subnodes of root node alphabetically to eas future maintence overhead * Draak board with R-Car D3 (r8a77995) SoC - Enable SDHI2 Wolfram Sang says "The single SDHI controller is connected to eMMC." - Enable DU Kieran Bingham says "Enable the DU, providing only the VGA output for now." * R-Car D3 (r8a77995) and V3M (r8a77970) SoCs - Move nodes which have no reg property out of bus By deffinition the bus only has hardware with an address on the bus - Remove non-existing STBE region from EtherAVB Stream Buffer for EtherAVB-IF (STBE) is not present on these SoCs * R-Car D3 (r8a77995) SoC - Add FCPV, VSP and DU support Kieran Bingham says "The r8a77995-d3 platform supports 3 VSP instances. One VSPBS can be used as a dual-input image blender, while two VSPD instances can be utilised as part of a display (DU) pipeline. Add support for these, along with their required FCPV nodes." * Salvator-X and Salvator-XS boards with R-Car Gen3 SoCs - Add GPIO extender This is a basis for follow-up work to configure the GPIOs of the extender * Salvator-X and Salvator-XS board with R-Car M3-N (r8a77965) SoC - Initial upstream support * R-Car H3 (r8a7795) and M3-W (r8a7796) SoCs - Add OPPs table for cpu devices This, along with recently upstreamed Z and Z2 clock support allows use of CPUFreq with both A57 and A53 CPUs. - Add thermal cooling management Allows the use of CPUFreq as a cooling device on A57 CPUs - Correct register size of thermal node Niklas Söderlund says "To be able to read fused calibration values from hardware the size of the register resource of TSC1 needs to be incremented to cover one more register which holds the information if the calibration values have been fused or not. Instead of increasing TSC1 size to the value from the datasheet update all TSC's size to the smallest granularity of the address decoder circuitry" - Fix register mappings on VSPs Kieran Bingham says "The VSPD includes a CLUT on RPF2. Ensure that the register space is mapped correctly to support this." * R-Car H3 (r8a7795) SoC - Move SCIF node into alphabetical order to ease future maintenance overhead - Add IPMMU-PV1 device node This resolves an oversight when IPMMU nodes were added to the H3 DT. All IPMMU devices should now be described in DT. - Add missing SYS-DMAC2 dmas Geert Uytterhoeven says "On R-Car H3, on-chip peripheral modules that can make use of DMA are wired to either SYS-DMAC0 only, or to both SYS-DMAC1 and SYS-DMAC2. Add the missing DMA properties pointing to SYS-DMAC2 for HSCIF[0-2], SCIF[0125], and I2C[0-2]. These were initially left out because early firmware versions prohibited using SYS-DMAC2. This restriction has been lifted in IPL and Secure Monitor Rev1.0.6 (released on Feb 25, 2016)." ---------------------------------------------------------------- Dien Pham (4): arm64: dts: renesas: r8a7795: Add OPPs table for cpu devices arm64: dts: renesas: r8a7796: Add OPPs table for cpu devices arm64: dts: renesas: r8a7796: Update OPPs to support CA53 dfs arm64: dts: renesas: r8a7795: Update OPPs to support CA53 dfs Geert Uytterhoeven (7): arm64: dts: renesas: r8a77970: Remove non-existing STBE region arm64: dts: renesas: r8a77995: Remove non-existing STBE region arm64: dts: renesas: r8a77965: Add IIC-DVFS device node arm64: dts: renesas: r8a77965: Add INTC-EX device node arm64: dts: renesas: r8a77965-salvator-xs: Add SoC name to file header arm64: dts: renesas: r8a77970: sort subnodes of root node alphabetically arm64: dts: renesas: r8a7795: Add missing SYS-DMAC2 dmas Jacopo Mondi (23): arm64: add Renesas R8A77965 support arm64: dts: renesas: initial R8A77965 SoC device tree arm64: dts: renesas: Add R-Car Salvator-x M3-N support arm64: dts: renesas: r8a77965: Add dmac device nods arm64: dts: renesas: r8a77965: Add SCIF device nodes arm64: dts: renesas: r8a77965: Add GPIO nodes arm64: dts: renesas: r8a77965: Add "reg" properties arm64: dts: renesas: r8a77965: Add #address-cells and #size-cells arm64: dts: renesas: r8a77965: Remove stale reg property arm64: dts: renesas: r8a77965: Add #phy-cells property arm64: dts: renesas: r8a77965: Add #pwm-cells property arm64: dts: renesas: r8a77965: Add #interrupt-cells property arm64: dts: renesas: r8a77965: Move usb2_phy1 up arm64: dts: renesas: salvator-common: Override EtherAVB phy-mode arm64: dts: renesas: ulcb: Override EtherAVB phy-mode arm64: dts: renesas: draak: Override EtherAVB phy-mode arm64: dts: renesas: eagle: Override EtherAVB phy-mode arm64: dts: renesas: v3msk: Override EtherAVB phy-mode arm64: dts: renesas: r8a7796: Set EtherAVB phy mode to "rgmii" arm64: dts: renesas: r8a7795: Set EtherAVB phy mode to "rgmii" arm64: dts: renesas: r8a77995: Set EtherAVB phy mode to "rgmii" arm64: dts: renesas: r8a77970: Set EtherAVB phy mode to "rgmii" arm64: dts: renesas: r8a77965: Add EtherAVB device node Kieran Bingham (7): arm64: dts: renesas: r8a77995: add FCPV nodes arm64: dts: renesas: r8a77995: add VSP instances arm64: dts: renesas: r8a77995: add DU support arm64: dts: renesas: r8a7795-es1: Fix register mappings on VSPs arm64: dts: renesas: r8a7795: Fix register mappings on VSPs arm64: dts: renesas: r8a7796: Fix register mappings on VSPs arm64: dts: renesas: draak: Enable DU Niklas Söderlund (4): arm64: dts: renesas: r8a7796: add thermal cooling management arm64: dts: renesas: r8a7795: add thermal cooling management arm64: dts: renesas: r8a7795: update register size for thermal arm64: dts: renesas: r8a7796: update register size for thermal Sergei Shtylyov (14): arm64: add Renesas R8A77980 support arm64: dts: renesas: initial R8A77980 SoC device tree arm64: dts: renesas: r8a77980: add SYS-DMAC support arm64: dts: renesas: r8a77970: add PFC support arm64: dts: renesas: eagle: add SCIF0 pins arm64: dts: renesas: r8a77970: add GPIO support arm64: dts: renesas: eagle: specify EtherAVB PHY IRQ arm64: dts: renesas: r8a77980: add [H]SCIF support arm64: dts: renesas: r8a77980: add EtherAVB support arm64: dts: renesas: initial Condor board device tree arm64: dts: renesas: condor: add EtherAVB support arm64: dts: renesas: r8a77970: add I2C support arm64: dts: renesas: eagle: add I2C0 support arm64: dts: renesas: v3msk: add SCIF0 pins Simon Horman (4): arm64: dts: renesas: r8a7795: move scif node into alphabetical order arm64: dts: renesas: r8a77970: move node which has no reg property out of bus arm64: dts: renesas: r8a77995: move nodes which have no reg property out of bus arm64: dts: renesas: r8a7795: Add IPMMU-PV1 device node Takeshi Kihara (1): arm64: dts: renesas: Add support for Salvator-XS with R-Car M3-N Ulrich Hecht (4): arm64: dts: renesas: r8a77995: add I2C support arm64: dts: renesas: draak: enable I2C controller 0 and EEPROM arm64: dts: renesas: draak: enable I2C controller 1 arm64: dts: renesas: draak: enable SDHI2 Wolfram Sang (1): arm64: dts: renesas: salvator-common: add GPIO extender arch/arm64/Kconfig.platforms | 12 + arch/arm64/boot/dts/renesas/Makefile | 2 + arch/arm64/boot/dts/renesas/r8a7795-es1.dtsi | 3 +- arch/arm64/boot/dts/renesas/r8a7795.dtsi | 194 ++++- arch/arm64/boot/dts/renesas/r8a7796.dtsi | 130 ++- .../arm64/boot/dts/renesas/r8a77965-salvator-x.dts | 21 + .../boot/dts/renesas/r8a77965-salvator-xs.dts | 21 + arch/arm64/boot/dts/renesas/r8a77965.dtsi | 878 +++++++++++++++++++++ arch/arm64/boot/dts/renesas/r8a77970-eagle.dts | 33 + arch/arm64/boot/dts/renesas/r8a77970-v3msk.dts | 11 + arch/arm64/boot/dts/renesas/r8a77970.dtsi | 218 ++++- arch/arm64/boot/dts/renesas/r8a77980-condor.dts | 58 ++ arch/arm64/boot/dts/renesas/r8a77980.dtsi | 385 +++++++++ arch/arm64/boot/dts/renesas/r8a77995-draak.dts | 124 +++ arch/arm64/boot/dts/renesas/r8a77995.dtsi | 193 ++++- arch/arm64/boot/dts/renesas/salvator-common.dtsi | 8 + arch/arm64/boot/dts/renesas/ulcb.dtsi | 1 + 17 files changed, 2216 insertions(+), 76 deletions(-) create mode 100644 arch/arm64/boot/dts/renesas/r8a77965-salvator-x.dts create mode 100644 arch/arm64/boot/dts/renesas/r8a77965-salvator-xs.dts create mode 100644 arch/arm64/boot/dts/renesas/r8a77965.dtsi create mode 100644 arch/arm64/boot/dts/renesas/r8a77980-condor.dts create mode 100644 arch/arm64/boot/dts/renesas/r8a77980.dtsi
