Hej Sakari,
On 2017-12-01 15:01:36 +0200, Sakari Ailus wrote:
> Hej Niklas,
>
> Tack för dina nya lappar!
Tack för dina kommentarer.
>
> On Wed, Nov 29, 2017 at 08:32:35PM +0100, Niklas Söderlund wrote:
> > A V4L2 driver for Renesas R-Car MIPI CSI-2 receiver. The driver
> > supports the rcar-vin driver on R-Car Gen3 SoCs where separate CSI-2
> > hardware blocks are connected between the video sources and the video
> > grabbers (VIN).
> >
> > Driver is based on a prototype by Koji Matsuoka in the Renesas BSP.
> >
> > Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@xxxxxxxxxxxx>
> > Reviewed-by: Hans Verkuil <hans.verkuil@xxxxxxxxx>
> > ---
> > drivers/media/platform/rcar-vin/Kconfig | 12 +
> > drivers/media/platform/rcar-vin/Makefile | 1 +
> > drivers/media/platform/rcar-vin/rcar-csi2.c | 898 ++++++++++++++++++++++++++++
> > 3 files changed, 911 insertions(+)
> > create mode 100644 drivers/media/platform/rcar-vin/rcar-csi2.c
> >
> > diff --git a/drivers/media/platform/rcar-vin/Kconfig b/drivers/media/platform/rcar-vin/Kconfig
> > index af4c98b44d2e22cb..6875f30c1ae42631 100644
> > --- a/drivers/media/platform/rcar-vin/Kconfig
> > +++ b/drivers/media/platform/rcar-vin/Kconfig
> > @@ -1,3 +1,15 @@
> > +config VIDEO_RCAR_CSI2
> > + tristate "R-Car MIPI CSI-2 Receiver"
> > + depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF
> > + depends on ARCH_RENESAS || COMPILE_TEST
> > + select V4L2_FWNODE
> > + ---help---
> > + Support for Renesas R-Car MIPI CSI-2 receiver.
> > + Supports R-Car Gen3 SoCs.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called rcar-csi2.
> > +
> > config VIDEO_RCAR_VIN
> > tristate "R-Car Video Input (VIN) Driver"
> > depends on VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API && OF && HAS_DMA && MEDIA_CONTROLLER
> > diff --git a/drivers/media/platform/rcar-vin/Makefile b/drivers/media/platform/rcar-vin/Makefile
> > index 48c5632c21dc060b..5ab803d3e7c1aa57 100644
> > --- a/drivers/media/platform/rcar-vin/Makefile
> > +++ b/drivers/media/platform/rcar-vin/Makefile
> > @@ -1,3 +1,4 @@
> > rcar-vin-objs = rcar-core.o rcar-dma.o rcar-v4l2.o
> >
> > +obj-$(CONFIG_VIDEO_RCAR_CSI2) += rcar-csi2.o
> > obj-$(CONFIG_VIDEO_RCAR_VIN) += rcar-vin.o
> > diff --git a/drivers/media/platform/rcar-vin/rcar-csi2.c b/drivers/media/platform/rcar-vin/rcar-csi2.c
> > new file mode 100644
> > index 0000000000000000..30aafcbb7a3642c6
> > --- /dev/null
> > +++ b/drivers/media/platform/rcar-vin/rcar-csi2.c
> > @@ -0,0 +1,898 @@
> > +/*
> > + * Driver for Renesas R-Car MIPI CSI-2 Receiver
> > + *
> > + * Copyright (C) 2017 Renesas Electronics Corp.
> > + *
> > + * This program is free software; you can redistribute it and/or modify it
> > + * under the terms of the GNU General Public License as published by the
> > + * Free Software Foundation; either version 2 of the License, or (at your
> > + * option) any later version.
> > + */
> > +
> > +#include <linux/delay.h>
> > +#include <linux/interrupt.h>
> > +#include <linux/io.h>
> > +#include <linux/module.h>
> > +#include <linux/of.h>
> > +#include <linux/of_device.h>
> > +#include <linux/of_graph.h>
> > +#include <linux/platform_device.h>
> > +#include <linux/pm_runtime.h>
> > +#include <linux/sys_soc.h>
> > +
> > +#include <media/v4l2-ctrls.h>
> > +#include <media/v4l2-device.h>
> > +#include <media/v4l2-fwnode.h>
> > +#include <media/v4l2-mc.h>
> > +#include <media/v4l2-subdev.h>
> > +
> > +/* Register offsets and bits */
> > +
> > +/* Control Timing Select */
> > +#define TREF_REG 0x00
> > +#define TREF_TREF BIT(0)
> > +
> > +/* Software Reset */
> > +#define SRST_REG 0x04
> > +#define SRST_SRST BIT(0)
> > +
> > +/* PHY Operation Control */
> > +#define PHYCNT_REG 0x08
> > +#define PHYCNT_SHUTDOWNZ BIT(17)
> > +#define PHYCNT_RSTZ BIT(16)
> > +#define PHYCNT_ENABLECLK BIT(4)
> > +#define PHYCNT_ENABLE_3 BIT(3)
> > +#define PHYCNT_ENABLE_2 BIT(2)
> > +#define PHYCNT_ENABLE_1 BIT(1)
> > +#define PHYCNT_ENABLE_0 BIT(0)
> > +
> > +/* Checksum Control */
> > +#define CHKSUM_REG 0x0c
> > +#define CHKSUM_ECC_EN BIT(1)
> > +#define CHKSUM_CRC_EN BIT(0)
> > +
> > +/*
> > + * Channel Data Type Select
> > + * VCDT[0-15]: Channel 1 VCDT[16-31]: Channel 2
> > + * VCDT2[0-15]: Channel 3 VCDT2[16-31]: Channel 4
> > + */
> > +#define VCDT_REG 0x10
> > +#define VCDT2_REG 0x14
> > +#define VCDT_VCDTN_EN BIT(15)
> > +#define VCDT_SEL_VC(n) (((n) & 0x3) << 8)
> > +#define VCDT_SEL_DTN_ON BIT(6)
> > +#define VCDT_SEL_DT(n) (((n) & 0x3f) << 0)
> > +
> > +/* Frame Data Type Select */
> > +#define FRDT_REG 0x18
> > +
> > +/* Field Detection Control */
> > +#define FLD_REG 0x1c
> > +#define FLD_FLD_NUM(n) (((n) & 0xff) << 16)
> > +#define FLD_FLD_EN4 BIT(3)
> > +#define FLD_FLD_EN3 BIT(2)
> > +#define FLD_FLD_EN2 BIT(1)
> > +#define FLD_FLD_EN BIT(0)
> > +
> > +/* Automatic Standby Control */
> > +#define ASTBY_REG 0x20
> > +
> > +/* Long Data Type Setting 0 */
> > +#define LNGDT0_REG 0x28
> > +
> > +/* Long Data Type Setting 1 */
> > +#define LNGDT1_REG 0x2c
> > +
> > +/* Interrupt Enable */
> > +#define INTEN_REG 0x30
> > +
> > +/* Interrupt Source Mask */
> > +#define INTCLOSE_REG 0x34
> > +
> > +/* Interrupt Status Monitor */
> > +#define INTSTATE_REG 0x38
> > +#define INTSTATE_INT_ULPS_START BIT(7)
> > +#define INTSTATE_INT_ULPS_END BIT(6)
> > +
> > +/* Interrupt Error Status Monitor */
> > +#define INTERRSTATE_REG 0x3c
> > +
> > +/* Short Packet Data */
> > +#define SHPDAT_REG 0x40
> > +
> > +/* Short Packet Count */
> > +#define SHPCNT_REG 0x44
> > +
> > +/* LINK Operation Control */
> > +#define LINKCNT_REG 0x48
> > +#define LINKCNT_MONITOR_EN BIT(31)
> > +#define LINKCNT_REG_MONI_PACT_EN BIT(25)
> > +#define LINKCNT_ICLK_NONSTOP BIT(24)
> > +
> > +/* Lane Swap */
> > +#define LSWAP_REG 0x4c
> > +#define LSWAP_L3SEL(n) (((n) & 0x3) << 6)
> > +#define LSWAP_L2SEL(n) (((n) & 0x3) << 4)
> > +#define LSWAP_L1SEL(n) (((n) & 0x3) << 2)
> > +#define LSWAP_L0SEL(n) (((n) & 0x3) << 0)
> > +
> > +/* PHY Test Interface Write Register */
> > +#define PHTW_REG 0x50
> > +
> > +/* PHY Test Interface Clear */
> > +#define PHTC_REG 0x58
> > +#define PHTC_TESTCLR BIT(0)
> > +
> > +/* PHY Frequency Control */
> > +#define PHYPLL_REG 0x68
> > +#define PHYPLL_HSFREQRANGE(n) ((n) << 16)
> > +
> > +struct phypll_hsfreqrange {
> > + u16 mbps;
> > + u16 reg;
> > +};
> > +
> > +static const struct phypll_hsfreqrange hsfreqrange_h3_v3h_m3n[] = {
> > + { .mbps = 80, .reg = 0x00 },
> > + { .mbps = 90, .reg = 0x10 },
> > + { .mbps = 100, .reg = 0x20 },
> > + { .mbps = 110, .reg = 0x30 },
> > + { .mbps = 120, .reg = 0x01 },
> > + { .mbps = 130, .reg = 0x11 },
> > + { .mbps = 140, .reg = 0x21 },
> > + { .mbps = 150, .reg = 0x31 },
> > + { .mbps = 160, .reg = 0x02 },
> > + { .mbps = 170, .reg = 0x12 },
> > + { .mbps = 180, .reg = 0x22 },
> > + { .mbps = 190, .reg = 0x32 },
> > + { .mbps = 205, .reg = 0x03 },
> > + { .mbps = 220, .reg = 0x13 },
> > + { .mbps = 235, .reg = 0x23 },
> > + { .mbps = 250, .reg = 0x33 },
> > + { .mbps = 275, .reg = 0x04 },
> > + { .mbps = 300, .reg = 0x14 },
> > + { .mbps = 325, .reg = 0x25 },
> > + { .mbps = 350, .reg = 0x35 },
> > + { .mbps = 400, .reg = 0x05 },
> > + { .mbps = 450, .reg = 0x26 },
> > + { .mbps = 500, .reg = 0x36 },
> > + { .mbps = 550, .reg = 0x37 },
> > + { .mbps = 600, .reg = 0x07 },
> > + { .mbps = 650, .reg = 0x18 },
> > + { .mbps = 700, .reg = 0x28 },
> > + { .mbps = 750, .reg = 0x39 },
> > + { .mbps = 800, .reg = 0x09 },
> > + { .mbps = 850, .reg = 0x19 },
> > + { .mbps = 900, .reg = 0x29 },
> > + { .mbps = 950, .reg = 0x3a },
> > + { .mbps = 1000, .reg = 0x0a },
> > + { .mbps = 1050, .reg = 0x1a },
> > + { .mbps = 1100, .reg = 0x2a },
> > + { .mbps = 1150, .reg = 0x3b },
> > + { .mbps = 1200, .reg = 0x0b },
> > + { .mbps = 1250, .reg = 0x1b },
> > + { .mbps = 1300, .reg = 0x2b },
> > + { .mbps = 1350, .reg = 0x3c },
> > + { .mbps = 1400, .reg = 0x0c },
> > + { .mbps = 1450, .reg = 0x1c },
> > + { .mbps = 1500, .reg = 0x2c },
> > + /* guard */
> > + { .mbps = 0, .reg = 0x00 },
> > +};
> > +
> > +static const struct phypll_hsfreqrange hsfreqrange_m3w_h3es1[] = {
> > + { .mbps = 80, .reg = 0x00 },
> > + { .mbps = 90, .reg = 0x10 },
> > + { .mbps = 100, .reg = 0x20 },
> > + { .mbps = 110, .reg = 0x30 },
> > + { .mbps = 120, .reg = 0x01 },
> > + { .mbps = 130, .reg = 0x11 },
> > + { .mbps = 140, .reg = 0x21 },
> > + { .mbps = 150, .reg = 0x31 },
> > + { .mbps = 160, .reg = 0x02 },
> > + { .mbps = 170, .reg = 0x12 },
> > + { .mbps = 180, .reg = 0x22 },
> > + { .mbps = 190, .reg = 0x32 },
> > + { .mbps = 205, .reg = 0x03 },
> > + { .mbps = 220, .reg = 0x13 },
> > + { .mbps = 235, .reg = 0x23 },
> > + { .mbps = 250, .reg = 0x33 },
> > + { .mbps = 275, .reg = 0x04 },
> > + { .mbps = 300, .reg = 0x14 },
> > + { .mbps = 325, .reg = 0x05 },
> > + { .mbps = 350, .reg = 0x15 },
> > + { .mbps = 400, .reg = 0x25 },
> > + { .mbps = 450, .reg = 0x06 },
> > + { .mbps = 500, .reg = 0x16 },
> > + { .mbps = 550, .reg = 0x07 },
> > + { .mbps = 600, .reg = 0x17 },
> > + { .mbps = 650, .reg = 0x08 },
> > + { .mbps = 700, .reg = 0x18 },
> > + { .mbps = 750, .reg = 0x09 },
> > + { .mbps = 800, .reg = 0x19 },
> > + { .mbps = 850, .reg = 0x29 },
> > + { .mbps = 900, .reg = 0x39 },
> > + { .mbps = 950, .reg = 0x0A },
> > + { .mbps = 1000, .reg = 0x1A },
> > + { .mbps = 1050, .reg = 0x2A },
> > + { .mbps = 1100, .reg = 0x3A },
> > + { .mbps = 1150, .reg = 0x0B },
> > + { .mbps = 1200, .reg = 0x1B },
> > + { .mbps = 1250, .reg = 0x2B },
> > + { .mbps = 1300, .reg = 0x3B },
> > + { .mbps = 1350, .reg = 0x0C },
> > + { .mbps = 1400, .reg = 0x1C },
> > + { .mbps = 1450, .reg = 0x2C },
> > + { .mbps = 1500, .reg = 0x3C },
> > + /* guard */
> > + { .mbps = 0, .reg = 0x00 },
> > +};
> > +
> > +/* PHY ESC Error Monitor */
> > +#define PHEERM_REG 0x74
> > +
> > +/* PHY Clock Lane Monitor */
> > +#define PHCLM_REG 0x78
> > +
> > +/* PHY Data Lane Monitor */
> > +#define PHDLM_REG 0x7c
> > +
> > +/* CSI0CLK Frequency Configuration Preset Register */
> > +#define CSI0CLKFCPR_REG 0x260
> > +#define CSI0CLKFREQRANGE(n) ((n & 0x3f) << 16)
> > +
> > +struct rcar_csi2_format {
> > + unsigned int code;
>
> Media bus codes are generally u32, I'd use the same here, too.
Good point, will change this.
>
> > + unsigned int datatype;
> > + unsigned int bpp;
> > +};
> > +
> > +static const struct rcar_csi2_format rcar_csi2_formats[] = {
> > + { .code = MEDIA_BUS_FMT_RGB888_1X24, .datatype = 0x24, .bpp = 24 },
> > + { .code = MEDIA_BUS_FMT_UYVY8_1X16, .datatype = 0x1e, .bpp = 16 },
> > + { .code = MEDIA_BUS_FMT_UYVY8_2X8, .datatype = 0x1e, .bpp = 16 },
> > + { .code = MEDIA_BUS_FMT_YUYV10_2X10, .datatype = 0x1e, .bpp = 16 },
> > +};
> > +
> > +static const struct rcar_csi2_format *rcar_csi2_code_to_fmt(unsigned int code)
> > +{
> > + unsigned int i;
> > +
> > + for (i = 0; i < ARRAY_SIZE(rcar_csi2_formats); i++)
> > + if (rcar_csi2_formats[i].code == code)
> > + return rcar_csi2_formats + i;
> > +
> > + return NULL;
> > +}
> > +
> > +enum rcar_csi2_pads {
> > + RCAR_CSI2_SINK,
> > + RCAR_CSI2_SOURCE_VC0,
> > + RCAR_CSI2_SOURCE_VC1,
> > + RCAR_CSI2_SOURCE_VC2,
> > + RCAR_CSI2_SOURCE_VC3,
> > + NR_OF_RCAR_CSI2_PAD,
> > +};
> > +
> > +struct rcar_csi2_info {
> > + const struct phypll_hsfreqrange *hsfreqrange;
> > + unsigned int csi0clkfreqrange;
> > + bool clear_ulps;
> > + bool init_phtw;
> > +};
> > +
> > +struct rcar_csi2 {
> > + struct device *dev;
> > + void __iomem *base;
> > + const struct rcar_csi2_info *info;
> > +
> > + struct v4l2_subdev subdev;
> > + struct media_pad pads[NR_OF_RCAR_CSI2_PAD];
> > +
> > + struct v4l2_async_notifier notifier;
> > + struct v4l2_async_subdev remote;
> > +
> > + struct v4l2_mbus_framefmt mf;
> > +
> > + struct mutex lock;
> > + int stream_count;
> > +
> > + unsigned short lanes;
> > + unsigned char lane_swap[4];
> > +};
> > +
> > +static inline struct rcar_csi2 *sd_to_csi2(struct v4l2_subdev *sd)
> > +{
> > + return container_of(sd, struct rcar_csi2, subdev);
> > +}
> > +
> > +static inline struct rcar_csi2 *notifier_to_csi2(struct v4l2_async_notifier *n)
> > +{
> > + return container_of(n, struct rcar_csi2, notifier);
> > +}
> > +
> > +static u32 rcar_csi2_read(struct rcar_csi2 *priv, unsigned int reg)
> > +{
> > + return ioread32(priv->base + reg);
> > +}
> > +
> > +static void rcar_csi2_write(struct rcar_csi2 *priv, unsigned int reg, u32 data)
> > +{
> > + iowrite32(data, priv->base + reg);
> > +}
> > +
> > +static void rcar_csi2_reset(struct rcar_csi2 *priv)
> > +{
> > + rcar_csi2_write(priv, SRST_REG, SRST_SRST);
> > + usleep_range(100, 150);
> > + rcar_csi2_write(priv, SRST_REG, 0);
> > +}
> > +
> > +static int rcar_csi2_wait_phy_start(struct rcar_csi2 *priv)
> > +{
> > + int timeout;
> > +
> > + /* Wait for the clock and data lanes to enter LP-11 state. */
> > + for (timeout = 100; timeout > 0; timeout--) {
> > + const u32 lane_mask = (1 << priv->lanes) - 1;
> > +
> > + if ((rcar_csi2_read(priv, PHCLM_REG) & 1) == 1 &&
> > + (rcar_csi2_read(priv, PHDLM_REG) & lane_mask) == lane_mask)
> > + return 0;
> > +
> > + msleep(20);
> > + }
> > +
> > + dev_err(priv->dev, "Timeout waiting for LP-11 state\n");
> > +
> > + return -ETIMEDOUT;
> > +}
> > +
> > +static int rcar_csi2_calc_phypll(struct rcar_csi2 *priv, unsigned int bpp,
> > + u32 *phypll)
> > +{
> > +
> > + const struct phypll_hsfreqrange *hsfreq;
> > + struct media_pad *pad, *source_pad;
> > + struct v4l2_subdev *source = NULL;
> > + struct v4l2_ctrl *ctrl;
> > + u64 mbps;
> > +
> > + /* Get remote subdevice */
> > + pad = &priv->subdev.entity.pads[RCAR_CSI2_SINK];
> > + source_pad = media_entity_remote_pad(pad);
> > + if (!source_pad) {
> > + dev_err(priv->dev, "Could not find remote source pad\n");
> > + return -ENODEV;
> > + }
> > + source = media_entity_to_v4l2_subdev(source_pad->entity);
> > +
> > + dev_dbg(priv->dev, "Using source %s pad: %u\n", source->name,
> > + source_pad->index);
> > +
> > + /* Read the pixel rate control from remote */
> > + ctrl = v4l2_ctrl_find(source->ctrl_handler, V4L2_CID_PIXEL_RATE);
> > + if (!ctrl) {
> > + dev_err(priv->dev, "no link freq control in subdev %s\n",
> > + source->name);
> > + return -EINVAL;
> > + }
> > +
> > + /* Calculate the phypll */
> > + mbps = v4l2_ctrl_g_ctrl_int64(ctrl) * bpp;
> > + do_div(mbps, priv->lanes * 1000000);
> > +
> > + for (hsfreq = priv->info->hsfreqrange; hsfreq->mbps != 0; hsfreq++)
> > + if (hsfreq->mbps >= mbps)
> > + break;
> > +
> > + if (!hsfreq->mbps) {
> > + dev_err(priv->dev, "Unsupported PHY speed (%llu Mbps)", mbps);
> > + return -ERANGE;
> > + }
> > +
> > + dev_dbg(priv->dev, "PHY HSFREQRANGE requested %llu got %u Mbps\n", mbps,
> > + hsfreq->mbps);
> > +
> > + *phypll = PHYPLL_HSFREQRANGE(hsfreq->reg);
> > +
> > + return 0;
> > +}
> > +
> > +static int rcar_csi2_start(struct rcar_csi2 *priv)
> > +{
> > + const struct rcar_csi2_format *format;
> > + u32 phycnt, phypll, tmp;
> > + u32 vcdt = 0, vcdt2 = 0;
> > + unsigned int i;
> > + int ret;
> > +
> > + dev_dbg(priv->dev, "Input size (%ux%u%c)\n",
> > + priv->mf.width, priv->mf.height,
> > + priv->mf.field == V4L2_FIELD_NONE ? 'p' : 'i');
> > +
> > + /* Code is validated in set_ftm */
> > + format = rcar_csi2_code_to_fmt(priv->mf.code);
> > +
> > + /*
> > + * Enable all Virtual Channels
> > + *
> > + * NOTE: It's not possible to get individual datatype for each
> > + * source virtual channel. Once this is possible in V4L2
> > + * it should be used here.
> > + */
> > + for (i = 0; i < 4; i++) {
> > + tmp = VCDT_SEL_VC(i) | VCDT_VCDTN_EN | VCDT_SEL_DTN_ON |
> > + VCDT_SEL_DT(format->datatype);
> > +
> > + /* Store in correct reg and offset */
> > + if (i < 2)
> > + vcdt |= tmp << ((i % 2) * 16);
> > + else
> > + vcdt2 |= tmp << ((i % 2) * 16);
> > + }
> > +
> > + switch (priv->lanes) {
> > + case 1:
> > + phycnt = PHYCNT_ENABLECLK | PHYCNT_ENABLE_0;
> > + break;
> > + case 2:
> > + phycnt = PHYCNT_ENABLECLK | PHYCNT_ENABLE_1 | PHYCNT_ENABLE_0;
> > + break;
> > + case 4:
> > + phycnt = PHYCNT_ENABLECLK | PHYCNT_ENABLE_3 | PHYCNT_ENABLE_2 |
> > + PHYCNT_ENABLE_1 | PHYCNT_ENABLE_0;
> > + break;
> > + default:
> > + return -EINVAL;
> > + }
> > +
> > + ret = rcar_csi2_calc_phypll(priv, format->bpp, &phypll);
> > + if (ret)
> > + return ret;
> > +
> > + /* Clear Ultra Low Power interrupt */
> > + if (priv->info->clear_ulps)
> > + rcar_csi2_write(priv, INTSTATE_REG,
> > + INTSTATE_INT_ULPS_START |
> > + INTSTATE_INT_ULPS_END);
> > +
> > + /* Init */
> > + rcar_csi2_write(priv, TREF_REG, TREF_TREF);
> > + rcar_csi2_reset(priv);
> > + rcar_csi2_write(priv, PHTC_REG, 0);
> > +
> > + /* Configure */
> > + rcar_csi2_write(priv, FLD_REG, FLD_FLD_NUM(2) | FLD_FLD_EN4 |
> > + FLD_FLD_EN3 | FLD_FLD_EN2 | FLD_FLD_EN);
> > + rcar_csi2_write(priv, VCDT_REG, vcdt);
> > + rcar_csi2_write(priv, VCDT2_REG, vcdt2);
> > + /* Lanes are zero indexed */
> > + rcar_csi2_write(priv, LSWAP_REG,
> > + LSWAP_L0SEL(priv->lane_swap[0] - 1) |
> > + LSWAP_L1SEL(priv->lane_swap[1] - 1) |
> > + LSWAP_L2SEL(priv->lane_swap[2] - 1) |
> > + LSWAP_L3SEL(priv->lane_swap[3] - 1));
> > +
> > + if (priv->info->init_phtw) {
> > + /*
> > + * This is for H3 ES2.0
> > + *
> > + * NOTE: Additional logic is needed here when
> > + * support for V3H and/or M3-N is added
> > + */
> > + rcar_csi2_write(priv, PHTW_REG, 0x01cc01e2);
> > + rcar_csi2_write(priv, PHTW_REG, 0x010101e3);
> > + rcar_csi2_write(priv, PHTW_REG, 0x010101e4);
> > + rcar_csi2_write(priv, PHTW_REG, 0x01100104);
> > + rcar_csi2_write(priv, PHTW_REG, 0x01030100);
> > + rcar_csi2_write(priv, PHTW_REG, 0x01800100);
> > + }
> > +
> > + /* Start */
> > + rcar_csi2_write(priv, PHYPLL_REG, phypll);
> > +
> > + /* Set frequency range if we have it */
> > + if (priv->info->csi0clkfreqrange)
> > + rcar_csi2_write(priv, CSI0CLKFCPR_REG,
> > + CSI0CLKFREQRANGE(priv->info->csi0clkfreqrange));
> > +
> > + rcar_csi2_write(priv, PHYCNT_REG, phycnt);
> > + rcar_csi2_write(priv, LINKCNT_REG, LINKCNT_MONITOR_EN |
> > + LINKCNT_REG_MONI_PACT_EN | LINKCNT_ICLK_NONSTOP);
> > + rcar_csi2_write(priv, PHYCNT_REG, phycnt | PHYCNT_SHUTDOWNZ);
> > + rcar_csi2_write(priv, PHYCNT_REG, phycnt | PHYCNT_SHUTDOWNZ |
> > + PHYCNT_RSTZ);
> > +
> > + return rcar_csi2_wait_phy_start(priv);
> > +}
> > +
> > +static void rcar_csi2_stop(struct rcar_csi2 *priv)
> > +{
> > + rcar_csi2_write(priv, PHYCNT_REG, 0);
> > +
> > + rcar_csi2_reset(priv);
> > +}
> > +
> > +static int rcar_csi2_sd_info(struct rcar_csi2 *priv, struct v4l2_subdev **sd)
> > +{
> > + struct media_pad *pad;
> > +
> > + pad = media_entity_remote_pad(&priv->pads[RCAR_CSI2_SINK]);
> > + if (!pad) {
> > + dev_err(priv->dev, "Could not find remote pad\n");
> > + return -ENODEV;
> > + }
> > +
> > + *sd = media_entity_to_v4l2_subdev(pad->entity);
> > + if (!*sd) {
> > + dev_err(priv->dev, "Could not find remote subdevice\n");
> > + return -ENODEV;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int rcar_csi2_s_stream(struct v4l2_subdev *sd, int enable)
> > +{
> > + struct rcar_csi2 *priv = sd_to_csi2(sd);
> > + struct v4l2_subdev *nextsd;
> > + int ret;
> > +
> > + mutex_lock(&priv->lock);
> > +
> > + ret = rcar_csi2_sd_info(priv, &nextsd);
> > + if (ret)
> > + goto out;
> > +
> > + if (enable && priv->stream_count == 0) {
> > + pm_runtime_get_sync(priv->dev);
> > +
> > + ret = rcar_csi2_start(priv);
> > + if (ret) {
> > + pm_runtime_put(priv->dev);
> > + goto out;
> > + }
> > +
> > + ret = v4l2_subdev_call(nextsd, video, s_stream, 1);
> > + if (ret) {
> > + rcar_csi2_stop(priv);
> > + pm_runtime_put(priv->dev);
> > + goto out;
> > + }
> > + } else if (!enable && priv->stream_count == 1) {
> > + rcar_csi2_stop(priv);
> > + ret = v4l2_subdev_call(nextsd, video, s_stream, 0);
>
> I might just ignore the error here. Maybe complain as well?
Sure it might be better to ignore the error here, I will change this.
>
> > + pm_runtime_put(priv->dev);
> > + }
> > +
> > + priv->stream_count += enable ? 1 : -1;
> > +out:
> > + mutex_unlock(&priv->lock);
> > +
> > + return ret;
> > +}
> > +
> > +static int rcar_csi2_set_pad_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *format)
> > +{
> > + struct rcar_csi2 *priv = sd_to_csi2(sd);
> > + struct v4l2_mbus_framefmt *framefmt;
> > +
> > + if (!rcar_csi2_code_to_fmt(format->format.code))
> > + return -EINVAL;
> > +
> > + if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE) {
> > + priv->mf = format->format;
> > + } else {
> > + framefmt = v4l2_subdev_get_try_format(sd, cfg, 0);
> > + *framefmt = format->format;
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int rcar_csi2_get_pad_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *format)
> > +{
> > + struct rcar_csi2 *priv = sd_to_csi2(sd);
> > +
> > + if (format->which == V4L2_SUBDEV_FORMAT_ACTIVE)
> > + format->format = priv->mf;
> > + else
> > + format->format = *v4l2_subdev_get_try_format(sd, cfg, 0);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct v4l2_subdev_video_ops rcar_csi2_video_ops = {
> > + .s_stream = rcar_csi2_s_stream,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops rcar_csi2_pad_ops = {
> > + .set_fmt = rcar_csi2_set_pad_format,
> > + .get_fmt = rcar_csi2_get_pad_format,
> > +};
> > +
> > +static const struct v4l2_subdev_ops rcar_csi2_subdev_ops = {
> > + .video = &rcar_csi2_video_ops,
> > + .pad = &rcar_csi2_pad_ops,
> > +};
> > +
> > +/* -----------------------------------------------------------------------------
> > + * Async and registered of subdevices and links
> > + */
> > +
> > +static int rcar_csi2_notify_bound(struct v4l2_async_notifier *notifier,
> > + struct v4l2_subdev *subdev,
> > + struct v4l2_async_subdev *asd)
> > +{
> > + struct rcar_csi2 *priv = notifier_to_csi2(notifier);
> > + int pad;
> > +
> > + v4l2_set_subdev_hostdata(subdev, priv);
>
> Do you need this?
Don't look like I do, I will remove this.
>
> > +
> > + pad = media_entity_get_fwnode_pad(&subdev->entity,
> > + asd->match.fwnode.fwnode,
> > + MEDIA_PAD_FL_SOURCE);
> > + if (pad < 0) {
> > + dev_err(priv->dev, "Failed to find pad for %s\n", subdev->name);
> > + return pad;
> > + }
> > +
> > + dev_dbg(priv->dev, "Bound %s pad: %d\n", subdev->name, pad);
> > +
> > + return media_create_pad_link(&subdev->entity, pad,
> > + &priv->subdev.entity, 0,
> > + MEDIA_LNK_FL_ENABLED |
> > + MEDIA_LNK_FL_IMMUTABLE);
> > +}
> > +
> > +static const struct v4l2_async_notifier_operations rcar_csi2_notify_ops = {
> > + .bound = rcar_csi2_notify_bound,
> > +};
> > +
> > +static int rcar_csi2_parse_v4l2(struct rcar_csi2 *priv,
> > + struct v4l2_fwnode_endpoint *vep)
> > +{
> > + unsigned int i;
> > +
> > + /* Only port 0 endpoint 0 is valid */
> > + if (vep->base.port || vep->base.id)
> > + return -ENOTCONN;
> > +
> > + if (vep->bus_type != V4L2_MBUS_CSI2) {
> > + dev_err(priv->dev, "Unsupported bus: 0x%x\n", vep->bus_type);
> > + return -EINVAL;
> > + }
> > +
> > + priv->lanes = vep->bus.mipi_csi2.num_data_lanes;
> > + if (priv->lanes != 1 && priv->lanes != 2 && priv->lanes != 4) {
> > + dev_err(priv->dev, "Unsupported number of data-lanes: %d\n",
> > + priv->lanes);
> > + return -EINVAL;
> > + }
> > +
> > + for (i = 0; i < ARRAY_SIZE(priv->lane_swap); i++) {
> > + priv->lane_swap[i] = i < priv->lanes ?
> > + vep->bus.mipi_csi2.data_lanes[i] : i;
> > +
> > + /* Check for valid lane number */
> > + if (priv->lane_swap[i] < 1 || priv->lane_swap[i] > 4) {
> > + dev_err(priv->dev, "data-lanes must be in 1-4 range\n");
> > + return -EINVAL;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int rcar_csi2_parse_dt(struct rcar_csi2 *priv)
> > +{
> > + struct device_node *ep;
> > + struct v4l2_fwnode_endpoint v4l2_ep;
> > + int ret;
> > +
> > + ep = of_graph_get_endpoint_by_regs(priv->dev->of_node, 0, 0);
> > + if (!ep) {
> > + dev_err(priv->dev, "Not connected to subdevice\n");
> > + return -EINVAL;
> > + }
> > +
> > + ret = v4l2_fwnode_endpoint_parse(of_fwnode_handle(ep), &v4l2_ep);
> > + if (ret) {
> > + dev_err(priv->dev, "Could not parse v4l2 endpoint\n");
> > + of_node_put(ep);
> > + return -EINVAL;
> > + }
> > +
> > + ret = rcar_csi2_parse_v4l2(priv, &v4l2_ep);
> > + if (ret)
> > + return ret;
> > +
> > + priv->remote.match.fwnode.fwnode =
> > + fwnode_graph_get_remote_endpoint(of_fwnode_handle(ep));
>
> To continue the discussion from v10 --- how does this work? The V4L2 async
> framework does still matching for the node of the device, not the endpoint.
>
> My suggestion is to handle this in match_fwnode until all drivers have been
> converted. The V4L2 fwnode helper should be changed as well, then you could
> use it here, too.
I agree that the V4L2 async framework should be changed to work with
endpoints and not the node of the device. I also agree on how this
change should be introduced.
But I don't feel that this change of the framework needs to block this
patch-set. Once the framework is updated to work with endpoints it
should be a trivial patch to change rcar-csi2 to use the new helper. Do
you agree whit this or do you feel that this patch-set should depend on
such change of the framework?
>
> > + priv->remote.match_type = V4L2_ASYNC_MATCH_FWNODE;
> > +
> > + of_node_put(ep);
> > +
> > + priv->notifier.subdevs = devm_kzalloc(priv->dev,
> > + sizeof(*priv->notifier.subdevs),
> > + GFP_KERNEL);
> > + if (priv->notifier.subdevs == NULL)
> > + return -ENOMEM;
> > +
> > + priv->notifier.num_subdevs = 1;
> > + priv->notifier.subdevs[0] = &priv->remote;
> > + priv->notifier.ops = &rcar_csi2_notify_ops;
> > +
> > + dev_dbg(priv->dev, "Found '%pOF'\n",
> > + to_of_node(priv->remote.match.fwnode.fwnode));
> > +
> > + return v4l2_async_subdev_notifier_register(&priv->subdev,
> > + &priv->notifier);
> > +}
> > +
> > +/* -----------------------------------------------------------------------------
> > + * Platform Device Driver
> > + */
> > +
> > +static const struct media_entity_operations rcar_csi2_entity_ops = {
> > + .link_validate = v4l2_subdev_link_validate,
> > +};
> > +
> > +static int rcar_csi2_probe_resources(struct rcar_csi2 *priv,
> > + struct platform_device *pdev)
> > +{
> > + struct resource *res;
> > + int irq;
> > +
> > + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> > + priv->base = devm_ioremap_resource(&pdev->dev, res);
> > + if (IS_ERR(priv->base))
> > + return PTR_ERR(priv->base);
> > +
> > + irq = platform_get_irq(pdev, 0);
> > + if (irq < 0)
> > + return irq;
> > +
> > + return 0;
> > +}
> > +
> > +static const struct rcar_csi2_info rcar_csi2_info_r8a7795 = {
> > + .hsfreqrange = hsfreqrange_h3_v3h_m3n,
> > + .clear_ulps = true,
> > + .init_phtw = true,
> > + .csi0clkfreqrange = 0x20,
> > +};
> > +
> > +static const struct rcar_csi2_info rcar_csi2_info_r8a7795es1 = {
> > + .hsfreqrange = hsfreqrange_m3w_h3es1,
> > +};
> > +
> > +static const struct rcar_csi2_info rcar_csi2_info_r8a7796 = {
> > + .hsfreqrange = hsfreqrange_m3w_h3es1,
> > +};
> > +
> > +static const struct of_device_id rcar_csi2_of_table[] = {
> > + {
> > + .compatible = "renesas,r8a7795-csi2",
> > + .data = &rcar_csi2_info_r8a7795,
> > + },
> > + {
> > + .compatible = "renesas,r8a7796-csi2",
> > + .data = &rcar_csi2_info_r8a7796,
> > + },
> > + { /* sentinel */ },
> > +};
> > +MODULE_DEVICE_TABLE(of, rcar_csi2_of_table);
> > +
> > +static const struct soc_device_attribute r8a7795es1[] = {
> > + {
> > + .soc_id = "r8a7795", .revision = "ES1.*",
> > + .data = &rcar_csi2_info_r8a7795es1,
> > + },
> > + { /* sentinel */}
> > +};
> > +
> > +static int rcar_csi2_probe(struct platform_device *pdev)
> > +{
> > + const struct soc_device_attribute *attr;
> > + struct rcar_csi2 *priv;
> > + unsigned int i;
> > + int ret;
> > +
> > + priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
> > + if (!priv)
> > + return -ENOMEM;
> > +
> > + priv->info = of_device_get_match_data(&pdev->dev);
> > +
> > + /* r8a7795 ES1.x behaves different then ES2.0+ but no own compat */
> > + attr = soc_device_match(r8a7795es1);
> > + if (attr)
> > + priv->info = attr->data;
> > +
> > + priv->dev = &pdev->dev;
> > +
> > + mutex_init(&priv->lock);
> > + priv->stream_count = 0;
> > +
> > + ret = rcar_csi2_probe_resources(priv, pdev);
> > + if (ret) {
> > + dev_err(priv->dev, "Failed to get resources\n");
> > + return ret;
> > + }
> > +
> > + platform_set_drvdata(pdev, priv);
> > +
> > + ret = rcar_csi2_parse_dt(priv);
> > + if (ret)
> > + return ret;
> > +
> > + priv->subdev.owner = THIS_MODULE;
> > + priv->subdev.dev = &pdev->dev;
> > + v4l2_subdev_init(&priv->subdev, &rcar_csi2_subdev_ops);
> > + v4l2_set_subdevdata(&priv->subdev, &pdev->dev);
> > + snprintf(priv->subdev.name, V4L2_SUBDEV_NAME_SIZE, "%s %s",
> > + KBUILD_MODNAME, dev_name(&pdev->dev));
> > + priv->subdev.flags = V4L2_SUBDEV_FL_HAS_DEVNODE;
> > +
> > + priv->subdev.entity.function = MEDIA_ENT_F_PROC_VIDEO_PIXEL_FORMATTER;
> > + priv->subdev.entity.ops = &rcar_csi2_entity_ops;
> > +
> > + priv->pads[RCAR_CSI2_SINK].flags = MEDIA_PAD_FL_SINK;
> > + for (i = RCAR_CSI2_SOURCE_VC0; i < NR_OF_RCAR_CSI2_PAD; i++)
> > + priv->pads[i].flags = MEDIA_PAD_FL_SOURCE;
> > +
> > + ret = media_entity_pads_init(&priv->subdev.entity, NR_OF_RCAR_CSI2_PAD,
> > + priv->pads);
> > + if (ret)
> > + goto error;
> > +
> > + ret = v4l2_async_register_subdev(&priv->subdev);
> > + if (ret < 0)
> > + goto error;
> > +
> > + pm_runtime_enable(&pdev->dev);
>
> Is this enough for platform devices? Just wondering.
As far as I can tell from the documentation this should be enough. I'm
no expert on PM so if I'm wrong please let me know.
Geert: do I understand the documentation correctly?
>
> > +
> > + dev_info(priv->dev, "%d lanes found\n", priv->lanes);
>
> I'd use dev_dbg.
I'm thorn about this one. I agree that the information printed is not
critical. But I have found this useful when receiving logs from users
who have misconfigured there DTS with the wrong number of lines.
I'm open to changing this, but if it's a matter of taste I prefer to
keep it at a info level.
>
> > +
> > + return 0;
> > +
> > +error:
> > + v4l2_async_notifier_unregister(&priv->notifier);
> > + v4l2_async_notifier_cleanup(&priv->notifier);
> > +
> > + return ret;
> > +}
> > +
> > +static int rcar_csi2_remove(struct platform_device *pdev)
> > +{
> > + struct rcar_csi2 *priv = platform_get_drvdata(pdev);
> > +
> > + v4l2_async_notifier_unregister(&priv->notifier);
> > + v4l2_async_notifier_cleanup(&priv->notifier);
> > + v4l2_async_unregister_subdev(&priv->subdev);
> > +
> > + pm_runtime_disable(&pdev->dev);
> > +
> > + return 0;
> > +}
> > +
> > +static struct platform_driver __refdata rcar_csi2_pdrv = {
> > + .remove = rcar_csi2_remove,
> > + .probe = rcar_csi2_probe,
> > + .driver = {
> > + .name = "rcar-csi2",
> > + .of_match_table = of_match_ptr(rcar_csi2_of_table),
> > + },
> > +};
> > +
> > +module_platform_driver(rcar_csi2_pdrv);
> > +
> > +MODULE_AUTHOR("Niklas Söderlund <niklas.soderlund@xxxxxxxxxxxx>");
> > +MODULE_DESCRIPTION("Renesas R-Car MIPI CSI-2 receiver");
> > +MODULE_LICENSE("GPL v2");
>
> --
> Hälsningar,
>
> Sakari Ailus
> e-mail: sakari.ailus@xxxxxx
--
Regards,
Niklas Söderlund
