On Mon, Aug 2, 2021 at 6:23 PM Simon Horman <simon.horman@xxxxxxxxxxxx> wrote:
> On Mon, Aug 02, 2021 at 04:47:28PM +0200, Arnd Bergmann wrote:
> > ---
> > This version seems to pass my randconfig builds for the moment,
> > but that doesn't mean it's correct either. Please have a closer
> > look before this gets applied.
Thank you for taking a look, it seems I have done a particularly bad
job rebasing
the patch on top of the previous fix, leaving only the wrong bits ;-)
> > diff --git a/drivers/net/ethernet/mellanox/mlx5/core/Kconfig b/drivers/net/ethernet/mellanox/mlx5/core/Kconfig
> > index e1a5a79e27c7..3a752e57c1e5 100644
> > --- a/drivers/net/ethernet/mellanox/mlx5/core/Kconfig
> > +++ b/drivers/net/ethernet/mellanox/mlx5/core/Kconfig
> > @@ -12,6 +12,7 @@ config MLX5_CORE
> > depends on MLXFW || !MLXFW
> > depends on PTP_1588_CLOCK || !PTP_1588_CLOCK
> > depends on PCI_HYPERV_INTERFACE || !PCI_HYPERV_INTERFACE
> > + depends on NET_MAY_USE_SWITCHDEV
> > help
> > Core driver for low level functionality of the ConnectX-4 and
> > Connect-IB cards by Mellanox Technologies.
>
> MLX5_CORE does not appear to cover code that calls
> switchdev_bridge_port_offload.
Ah right, I did get a link failure with my test build, but it was an
unrelated one:
ld: drivers/net/ethernet/mellanox/mlx5/core/esw/sample.o: in function
`mlx5_esw_sample_skb':
sample.c:(.text+0x5b4): undefined reference to `psample_sample_packet'
I think that one needs
--- a/drivers/net/ethernet/mellanox/mlx5/core/Kconfig
+++ b/drivers/net/ethernet/mellanox/mlx5/core/Kconfig
@@ -90,6 +90,7 @@ config MLX5_BRIDGE
config MLX5_CLS_ACT
bool "MLX5 TC classifier action support"
depends on MLX5_ESWITCH && NET_CLS_ACT
+ depends on PSAMPLE=y || PSAMPLE=MLX5_CORE
default y
help
mlx5 ConnectX offloads support for TC classifier action (NET_CLS_ACT),
but this is unrelated and I have not tested that.
> > diff --git a/drivers/net/ethernet/mellanox/mlxsw/Kconfig b/drivers/net/ethernet/mellanox/mlxsw/Kconfig
> > index 12871c8dc7c1..dee3925bdaea 100644
> > --- a/drivers/net/ethernet/mellanox/mlxsw/Kconfig
> > +++ b/drivers/net/ethernet/mellanox/mlxsw/Kconfig
> > @@ -5,6 +5,7 @@
> >
> > config MLXSW_CORE
> > tristate "Mellanox Technologies Switch ASICs support"
> > + depends on NET_MAY_USE_SWITCHDEV
> > select NET_DEVLINK
> > select MLXFW
> > help
>
> I think it is MLXSW_SPECTRUM rather than MLXSW_CORE
> that controls compilation of spectrum_switchdev.c
> which calls switchdev_bridge_port_offload.
>
> But MLXSW_SPECTRUM seems to already depend on BRIDGE || BRIDGE=n
Ok.
> > diff --git a/drivers/net/ethernet/netronome/Kconfig b/drivers/net/ethernet/netronome/Kconfig
> > index b82758d5beed..a298d19e8383 100644
> > --- a/drivers/net/ethernet/netronome/Kconfig
> > +++ b/drivers/net/ethernet/netronome/Kconfig
> > @@ -21,6 +21,7 @@ config NFP
> > depends on PCI && PCI_MSI
> > depends on VXLAN || VXLAN=n
> > depends on TLS && TLS_DEVICE || TLS_DEVICE=n
> > + depends on NET_MAY_USE_SWITCHDEV
> > select NET_DEVLINK
> > select CRC32
> > help
>
> This seems wrong, the NFP driver doesn't call
> switchdev_bridge_port_offload()
Ah right, I actually noticed that earlier and then forgot to remove that hunk.
Also: is this actually intended or should the driver call
switchdev_bridge_port_offload() like the other switchdev drivers do?
> > diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
> > index 07192613256e..a73c6c236b25 100644
> > --- a/drivers/net/ethernet/ti/Kconfig
> > +++ b/drivers/net/ethernet/ti/Kconfig
> > @@ -93,6 +93,7 @@ config TI_CPTS
> > config TI_K3_AM65_CPSW_NUSS
> > tristate "TI K3 AM654x/J721E CPSW Ethernet driver"
> > depends on OF && TI_K3_UDMA_GLUE_LAYER
> > + depends on NET_MAY_USE_SWITCHDEV
> > select NET_DEVLINK
> > select TI_DAVINCI_MDIO
> > imply PHY_TI_GMII_SEL
>
> I believe this has already been addressed by the following patch in net
>
> b0e81817629a ("net: build all switchdev drivers as modules when the bridge is a module")
I think the fix was wrong here, and that hunk should be reverted.
The dependency was added to a bool option, where it does not have
the intended effect.
I think this is the only remaining thing needed from my patch, so
the NET_MAY_USE_SWITCHDEV option is not needed either,
and it could be written as:
diff --git a/drivers/net/ethernet/ti/Kconfig b/drivers/net/ethernet/ti/Kconfig
index 07192613256e..e49006a96d49 100644
--- a/drivers/net/ethernet/ti/Kconfig
+++ b/drivers/net/ethernet/ti/Kconfig
@@ -93,6 +93,7 @@ config TI_CPTS
config TI_K3_AM65_CPSW_NUSS
tristate "TI K3 AM654x/J721E CPSW Ethernet driver"
depends on OF && TI_K3_UDMA_GLUE_LAYER
+ depends on (BRIDGE && NET_SWITCHDEV) || BRIDGE=n || NET_SWITCHDEV=n
select NET_DEVLINK
select TI_DAVINCI_MDIO
imply PHY_TI_GMII_SEL
@@ -110,7 +111,6 @@ config TI_K3_AM65_CPSW_NUSS
config TI_K3_AM65_CPSW_SWITCHDEV
bool "TI K3 AM654x/J721E CPSW Switch mode support"
depends on TI_K3_AM65_CPSW_NUSS
- depends on BRIDGE || BRIDGE=n
depends on NET_SWITCHDEV
help
This enables switchdev support for TI K3 CPSWxG Ethernet
If this looks correct to you, I can submit it as a standalone patch.
Arnd
