From: Stuart Hayes <stuart.w.hayes@xxxxxxxxx>
Without this commit, a PCIe hotplug port can stop generating interrupts
on hotplug events, so device adds and removals will not be seen:
The pciehp interrupt handler pciehp_isr() reads the Slot Status register
and then writes back to it to clear the bits that caused the interrupt.
If a different interrupt event bit gets set between the read and the
write, pciehp_isr() returns without having cleared all of the interrupt
event bits. If this happens when the MSI isn't masked (which by default
it isn't in handle_edge_irq(), and which it will never be when MSI
per-vector masking is not supported), we won't get any more hotplug
interrupts from that device.
That is expected behavior, according to the PCIe Base Spec r5.0, section
6.7.3.4, "Software Notification of Hot-Plug Events".
Because the Presence Detect Changed and Data Link Layer State Changed
event bits can both get set at nearly the same time when a device is
added or removed, this is more likely to happen than it might seem.
The issue was found (and can be reproduced rather easily) by connecting
and disconnecting an NVMe storage device on at least one system model
where the NVMe devices were being connected to an AMD PCIe port (PCI
device 0x1022/0x1483).
Fix the issue by modifying pciehp_isr() to loop back and re-read the
Slot Status register immediately after writing to it, until it sees that
all of the event status bits have been cleared.
Signed-off-by: Stuart Hayes <stuart.w.hayes@xxxxxxxxx>
[lukas: drop loop count limitation, write "events" instead of "status",
don't loop back in INTx and poll modes, tweak code comment & commit msg]
Signed-off-by: Lukas Wunner <lukas@xxxxxxxxx>
---
v4 (lukas):
* drop "MAX_ISR_STATUS_READS" loop count limitation
* drop unnecessary braces around PCI_EXP_SLTSTA_* flags
* write "events" instead of "status" variable to Slot Status register
to avoid unnecessary loop iterations if the same bit gets set
repeatedly
* don't loop back in INTx and poll modes
* shorten and tweak code comment & commit message
v3:
* removed pvm_capable flag (from v2) since MSI may not be masked
regardless of whether per-vector masking is supported
* tweaked comments
v2:
* fixed ctrl_warn() call
* improved comments
* added pvm_capable flag and changed pciehp_isr() to loop back only when
pvm_capable flag not set (suggested by Lukas Wunner)
drivers/pci/hotplug/pciehp_hpc.c | 26 ++++++++++++++++++++------
1 file changed, 20 insertions(+), 6 deletions(-)
diff --git a/drivers/pci/hotplug/pciehp_hpc.c b/drivers/pci/hotplug/pciehp_hpc.c
index 8a2cb1764386..f64d10df9eb5 100644
--- a/drivers/pci/hotplug/pciehp_hpc.c
+++ b/drivers/pci/hotplug/pciehp_hpc.c
@@ -527,7 +527,7 @@ static irqreturn_t pciehp_isr(int irq, void *dev_id)
struct controller *ctrl = (struct controller *)dev_id;
struct pci_dev *pdev = ctrl_dev(ctrl);
struct device *parent = pdev->dev.parent;
- u16 status, events;
+ u16 status, events = 0;
/*
* Interrupts only occur in D3hot or shallower and only if enabled
@@ -552,6 +552,7 @@ static irqreturn_t pciehp_isr(int irq, void *dev_id)
}
}
+read_status:
pcie_capability_read_word(pdev, PCI_EXP_SLTSTA, &status);
if (status == (u16) ~0) {
ctrl_info(ctrl, "%s: no response from device\n", __func__);
@@ -564,24 +565,37 @@ static irqreturn_t pciehp_isr(int irq, void *dev_id)
* Slot Status contains plain status bits as well as event
* notification bits; right now we only want the event bits.
*/
- events = status & (PCI_EXP_SLTSTA_ABP | PCI_EXP_SLTSTA_PFD |
- PCI_EXP_SLTSTA_PDC | PCI_EXP_SLTSTA_CC |
- PCI_EXP_SLTSTA_DLLSC);
+ status &= PCI_EXP_SLTSTA_ABP | PCI_EXP_SLTSTA_PFD |
+ PCI_EXP_SLTSTA_PDC | PCI_EXP_SLTSTA_CC |
+ PCI_EXP_SLTSTA_DLLSC;
/*
* If we've already reported a power fault, don't report it again
* until we've done something to handle it.
*/
if (ctrl->power_fault_detected)
- events &= ~PCI_EXP_SLTSTA_PFD;
+ status &= ~PCI_EXP_SLTSTA_PFD;
+ events |= status;
if (!events) {
if (parent)
pm_runtime_put(parent);
return IRQ_NONE;
}
- pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, events);
+ if (status) {
+ pcie_capability_write_word(pdev, PCI_EXP_SLTSTA, events);
+
+ /*
+ * In MSI mode, all event bits must be zero before the port
+ * will send a new interrupt (PCIe Base Spec r5.0 sec 6.7.3.4).
+ * So re-read the Slot Status register in case a bit was set
+ * between read and write.
+ */
+ if (pci_dev_msi_enabled(pdev) && !pciehp_poll_mode)
+ goto read_status;
+ }
+
ctrl_dbg(ctrl, "pending interrupts %#06x from Slot Status\n", events);
if (parent)
pm_runtime_put(parent);
--
2.24.0
