This PCI host bridge from V3 Semiconductor needs no further
introduction. An ancient driver for it has been sitting in
arch/arm/mach-integrator/pci_v3.* since before v2.6.12 and the
initial migration to git.
But we need to get the drivers out of arch/arm/* and get
proper handling of the old drivers, rewrite and clean up so
the PCI maintainer can control the mass of drivers without
having to run all over the kernel. We also switch swiftly
to all the new infrastructure found in the PCI hosts as of
late.
Some code is preserved so I have added an extensive list of
authors in the top comment section.
This driver probes with the following result:
OF: PCI: host bridge /pciv3@62000000 ranges:
OF: PCI: No bus range found for /pciv3@62000000, using [bus 00-ff]
OF: PCI: err 0x61000000..0x61ffffff -> 0x61000000
OF: PCI: IO 0x60000000..0x600fffff -> 0x00000000
OF: PCI: MEM 0x40000000..0x4fffffff -> 0x00000000
OF: PCI: MEM 0x50000000..0x5fffffff -> 0x10000000
pci-v3-semi 62000000.pciv3: BUS 0
pci-v3-semi 62000000.pciv3: CONFIG SPACE window start 61000000, size 01000000 (offset = 00000000, bus addr = 61000000)
pci-v3-semi 62000000.pciv3: I/O window start 00000000, bus addr 00000000, size 00100000
pci-v3-semi 62000000.pciv3: NON-PREFETCHABLE MEM window start 40000000, bus addr 00000000, size 10000000
pci-v3-semi 62000000.pciv3: PREFETCHABLE MEM window start 50000000, bus addr 10000000, size 10000000
pci-v3-semi 62000000.pciv3: FIFO_CFG: 0000 FIFO_PRIO: 0000
pci-v3-semi 62000000.pciv3: initialized PCI V3 Integrator/AP integration
pci-v3-semi 62000000.pciv3: PCI host bridge to bus 0000:00
pci_bus 0000:00: root bus resource [bus 00-ff]
pci_bus 0000:00: root bus resource [??? 0x61000000-0x61ffffff flags 0x0]
pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff] (bus address [0x00000000-0x0fffffff])
pci_bus 0000:00: root bus resource [mem 0x50000000-0x5fffffff pref] (bus address [0x10000000-0x1fffffff])
pci-v3-semi 62000000.pciv3: parity error interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
(...repeats a lot...)
pci 0000:00:0c.0: vgaarb: VGA device added: decodes=io+mem,owns=io,locks=none
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
pci-v3-semi 62000000.pciv3: master abort error interrupt
pci-v3-semi 62000000.pciv3: PCI target LB->PCI READ abort interrupt
(...repeats a lot...)
PCI: bus0: Fast back to back transfers disabled
PCI: bus1: Fast back to back transfers enabled
pci 0000:00:0c.0: BAR 0: assigned [mem 0x40000000-0x43ffffff]
pci 0000:00:0b.0: BAR 2: assigned [mem 0x44000000-0x440fffff]
pci 0000:00:0b.0: BAR 6: assigned [mem 0x50000000-0x500fffff pref]
pci 0000:00:0c.0: BAR 6: assigned [mem 0x50100000-0x5010ffff pref]
pci 0000:00:0b.0: BAR 0: assigned [mem 0x50110000-0x50110fff pref]
pci 0000:00:0b.0: BAR 1: assigned [io 0x1000-0x101f]
pci 0000:00:09.0: PCI bridge to [bus 01]
pci 0000:00:0b.0: Firmware left e100 interrupts enabled; disabling
(...)
e100: Intel(R) PRO/100 Network Driver, 3.5.24-k2-NAPI
e100: Copyright(c) 1999-2006 Intel Corporation
e100 0000:00:0b.0: enabling device (0146 -> 0147)
e100 0000:00:0b.0 eth0: addr 0x50110000, irq 0, MAC addr 00:08:c7:99:d2:57
> lspci
00:0b.0 Class 0200: 8086:1229
00:09.0 Class 0604: 1011:0024
00:0c.0 Class 0300: 5333:8811
> cat /proc/iomem
40000000-4fffffff : V3 PCI NON-PRE-MEM
40000000-43ffffff : 0000:00:0c.0
44000000-440fffff : 0000:00:0b.0
44000000-440fffff : e100
50000000-5fffffff : V3 PCI PRE-MEM
50000000-500fffff : 0000:00:0b.0
50100000-5010ffff : 0000:00:0c.0
50110000-50110fff : 0000:00:0b.0
50110000-50110fff : e100
61000000-61ffffff : V3 Config Space
62000000-6200ffff : /pciv3@62000000
As you can see the e100 network card is assigned IRQ0 which is
obviously wrong. I suspect the interrupt map in the device tree
to be wrong. It looks like this:
interrupt-map-mask = <0xf800 0 0 0x7>;
interrupt-map = <
/* IDSEL 9 */
0x4800 0 0 1 &pic 13 /* INT A on slot 9 is irq 13 */
0x4800 0 0 2 &pic 14 /* INT B on slot 9 is irq 14 */
0x4800 0 0 3 &pic 15 /* INT C on slot 9 is irq 15 */
0x4800 0 0 4 &pic 16 /* INT D on slot 9 is irq 16 */
/* IDSEL 10 */
0x5000 0 0 1 &pic 14 /* INT A on slot 10 is irq 14 */
0x5000 0 0 2 &pic 15 /* INT B on slot 10 is irq 15 */
0x5000 0 0 3 &pic 16 /* INT C on slot 10 is irq 16 */
0x5000 0 0 4 &pic 13 /* INT D on slot 10 is irq 13 */
/* IDSEL 11 */
0x5800 0 0 1 &pic 15 /* INT A on slot 11 is irq 15 */
0x5800 0 0 2 &pic 16 /* INT B on slot 11 is irq 16 */
0x5800 0 0 3 &pic 13 /* INT C on slot 11 is irq 13 */
0x5800 0 0 4 &pic 14 /* INT D on slot 11 is irq 14 */
/* IDSEL 12 */
0x6000 0 0 1 &pic 16 /* INT A on slot 12 is irq 16 */
0x6000 0 0 2 &pic 13 /* INT B on slot 12 is irq 13 */
0x6000 0 0 3 &pic 14 /* INT C on slot 12 is irq 14 */
0x6000 0 0 4 &pic 15 /* INT D on slot 12 is irq 15 */
Hints on how to fix this are welcomed.
Signed-off-by: Linus Walleij <linus.walleij@xxxxxxxxxx>
---
drivers/pci/host/Kconfig | 6 +
drivers/pci/host/Makefile | 1 +
drivers/pci/host/pci-v3-semi.c | 623 +++++++++++++++++++++++++++++++++++++++++
3 files changed, 630 insertions(+)
create mode 100644 drivers/pci/host/pci-v3-semi.c
diff --git a/drivers/pci/host/Kconfig b/drivers/pci/host/Kconfig
index 89d61c2cbfaa..bc7ba5a08559 100644
--- a/drivers/pci/host/Kconfig
+++ b/drivers/pci/host/Kconfig
@@ -95,6 +95,12 @@ config PCI_XGENE_MSI
Say Y here if you want PCIe MSI support for the APM X-Gene v1 SoC.
This MSI driver supports 5 PCIe ports on the APM X-Gene v1 SoC.
+config PCI_V3_SEMI
+ bool "V3 Semiconductor PCI controller"
+ depends on OF
+ depends on ARM
+ default ARCH_INTEGRATOR_AP
+
config PCI_VERSATILE
bool "ARM Versatile PB PCI controller"
depends on ARCH_VERSATILE
diff --git a/drivers/pci/host/Makefile b/drivers/pci/host/Makefile
index 12382785e02a..ee7cd492bb7f 100644
--- a/drivers/pci/host/Makefile
+++ b/drivers/pci/host/Makefile
@@ -9,6 +9,7 @@ obj-$(CONFIG_PCI_HOST_COMMON) += pci-host-common.o
obj-$(CONFIG_PCI_HOST_GENERIC) += pci-host-generic.o
obj-$(CONFIG_PCIE_XILINX) += pcie-xilinx.o
obj-$(CONFIG_PCIE_XILINX_NWL) += pcie-xilinx-nwl.o
+obj-$(CONFIG_PCI_V3_SEMI) += pci-v3-semi.o
obj-$(CONFIG_PCI_XGENE_MSI) += pci-xgene-msi.o
obj-$(CONFIG_PCI_VERSATILE) += pci-versatile.o
obj-$(CONFIG_PCIE_IPROC) += pcie-iproc.o
diff --git a/drivers/pci/host/pci-v3-semi.c b/drivers/pci/host/pci-v3-semi.c
new file mode 100644
index 000000000000..d44f0bcceae4
--- /dev/null
+++ b/drivers/pci/host/pci-v3-semi.c
@@ -0,0 +1,623 @@
+/*
+ * Support for V3 Semiconductor PCI Local Bus to PCI Bridge
+ * Copyright (C) 2017 Linus Walleij <linus.walleij@xxxxxxxxxx>
+ *
+ * Based on the code from arch/arm/mach-integrator/pci_v3.c
+ * Copyright (C) 1999 ARM Limited
+ * Copyright (C) 2000-2001 Deep Blue Solutions Ltd
+ *
+ * Contributors to the old driver include:
+ * Russell King <linux@xxxxxxxxxxxxxxx>
+ * David Rusling <david.rusling@xxxxxxxxxx>
+ * Rob Herring <robh@xxxxxxxxxx>
+ * Liviu Dudau <Liviu.Dudau@xxxxxxx>
+ * Grant Likely <grant.likely@xxxxxxxxxxxx>
+ * Arnd Bergmann <arnd@xxxxxxxx>
+ * Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
+ */
+#include <linux/init.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+#include <linux/of_irq.h>
+#include <linux/of_pci.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/bitops.h>
+#include <linux/irq.h>
+#include <linux/mfd/syscon.h>
+#include <linux/regmap.h>
+#include <linux/clk.h>
+
+#define V3_PCI_VENDOR 0x00000000
+#define V3_PCI_DEVICE 0x00000002
+#define V3_PCI_CMD 0x00000004
+#define V3_PCI_STAT 0x00000006
+#define V3_PCI_CC_REV 0x00000008
+#define V3_PCI_HDR_CFG 0x0000000C
+#define V3_PCI_IO_BASE 0x00000010
+#define V3_PCI_BASE0 0x00000014
+#define V3_PCI_BASE1 0x00000018
+#define V3_PCI_SUB_VENDOR 0x0000002C
+#define V3_PCI_SUB_ID 0x0000002E
+#define V3_PCI_ROM 0x00000030
+#define V3_PCI_BPARAM 0x0000003C
+#define V3_PCI_MAP0 0x00000040
+#define V3_PCI_MAP1 0x00000044
+#define V3_PCI_INT_STAT 0x00000048
+#define V3_PCI_INT_CFG 0x0000004C
+#define V3_LB_BASE0 0x00000054
+#define V3_LB_BASE1 0x00000058
+#define V3_LB_MAP0 0x0000005E
+#define V3_LB_MAP1 0x00000062
+#define V3_LB_BASE2 0x00000064
+#define V3_LB_MAP2 0x00000066
+#define V3_LB_SIZE 0x00000068
+#define V3_LB_IO_BASE 0x0000006E
+#define V3_FIFO_CFG 0x00000070
+#define V3_FIFO_PRIORITY 0x00000072
+#define V3_FIFO_STAT 0x00000074
+#define V3_LB_ISTAT 0x00000076
+#define V3_LB_IMASK 0x00000077
+#define V3_SYSTEM 0x00000078
+#define V3_LB_CFG 0x0000007A
+#define V3_PCI_CFG 0x0000007C
+#define V3_DMA_PCI_ADR0 0x00000080
+#define V3_DMA_PCI_ADR1 0x00000090
+#define V3_DMA_LOCAL_ADR0 0x00000084
+#define V3_DMA_LOCAL_ADR1 0x00000094
+#define V3_DMA_LENGTH0 0x00000088
+#define V3_DMA_LENGTH1 0x00000098
+#define V3_DMA_CSR0 0x0000008B
+#define V3_DMA_CSR1 0x0000009B
+#define V3_DMA_CTLB_ADR0 0x0000008C
+#define V3_DMA_CTLB_ADR1 0x0000009C
+#define V3_DMA_DELAY 0x000000E0
+#define V3_MAIL_DATA 0x000000C0
+#define V3_PCI_MAIL_IEWR 0x000000D0
+#define V3_PCI_MAIL_IERD 0x000000D2
+#define V3_LB_MAIL_IEWR 0x000000D4
+#define V3_LB_MAIL_IERD 0x000000D6
+#define V3_MAIL_WR_STAT 0x000000D8
+#define V3_MAIL_RD_STAT 0x000000DA
+#define V3_QBA_MAP 0x000000DC
+
+/* PCI STATUS bits */
+#define V3_PCI_STAT_PAR_ERR BIT(15)
+#define V3_PCI_STAT_SYS_ERR BIT(14)
+#define V3_PCI_STAT_M_ABORT_ERR BIT(13)
+#define V3_PCI_STAT_T_ABORT_ERR BIT(12)
+
+/* LB ISTAT bits */
+#define V3_LB_ISTAT_MAILBOX BIT(7)
+#define V3_LB_ISTAT_PCI_RD BIT(6)
+#define V3_LB_ISTAT_PCI_WR BIT(5)
+#define V3_LB_ISTAT_PCI_INT BIT(4)
+#define V3_LB_ISTAT_PCI_PERR BIT(3)
+#define V3_LB_ISTAT_I2O_QWR BIT(2)
+#define V3_LB_ISTAT_DMA1 BIT(1)
+#define V3_LB_ISTAT_DMA0 BIT(0)
+
+/* PCI COMMAND bits */
+#define V3_COMMAND_M_FBB_EN BIT(9)
+#define V3_COMMAND_M_SERR_EN BIT(8)
+#define V3_COMMAND_M_PAR_EN BIT(6)
+#define V3_COMMAND_M_MASTER_EN BIT(2)
+#define V3_COMMAND_M_MEM_EN BIT(1)
+#define V3_COMMAND_M_IO_EN BIT(0)
+
+/* SYSTEM bits */
+#define V3_SYSTEM_M_RST_OUT BIT(15)
+#define V3_SYSTEM_M_LOCK BIT(14)
+
+/* PCI CFG bits */
+#define V3_PCI_CFG_M_I2O_EN BIT(15)
+#define V3_PCI_CFG_M_IO_REG_DIS BIT(14)
+#define V3_PCI_CFG_M_IO_DIS BIT(13)
+#define V3_PCI_CFG_M_EN3V BIT(12)
+#define V3_PCI_CFG_M_RETRY_EN BIT(10)
+#define V3_PCI_CFG_M_AD_LOW1 BIT(9)
+#define V3_PCI_CFG_M_AD_LOW0 BIT(8)
+
+/* PCI BASE bits (PCI -> Local Bus) */
+#define V3_PCI_BASE_M_ADR_BASE 0xFFF00000U
+#define V3_PCI_BASE_M_ADR_BASEL 0x000FFF00U
+#define V3_PCI_BASE_M_PREFETCH BIT(3)
+#define V3_PCI_BASE_M_TYPE (3 << 1)
+#define V3_PCI_BASE_M_IO BIT(0)
+
+/* PCI MAP bits (PCI -> Local bus) */
+#define V3_PCI_MAP_M_MAP_ADR 0xFFF00000U
+#define V3_PCI_MAP_M_RD_POST_INH BIT(15)
+#define V3_PCI_MAP_M_ROM_SIZE (3 << 10)
+#define V3_PCI_MAP_M_SWAP (3 << 8)
+#define V3_PCI_MAP_M_ADR_SIZE 0x000000F0U
+#define V3_PCI_MAP_M_REG_EN BIT(1)
+#define V3_PCI_MAP_M_ENABLE BIT(0)
+
+/* LB_BASE0,1 bits (Local bus -> PCI) */
+#define V3_LB_BASE_ADR_BASE 0xfff00000U
+#define V3_LB_BASE_SWAP (3 << 8)
+#define V3_LB_BASE_ADR_SIZE (15 << 4)
+#define V3_LB_BASE_PREFETCH BIT(3)
+#define V3_LB_BASE_ENABLE BIT(0)
+
+#define V3_LB_BASE_ADR_SIZE_1MB (0 << 4)
+#define V3_LB_BASE_ADR_SIZE_2MB (1 << 4)
+#define V3_LB_BASE_ADR_SIZE_4MB (2 << 4)
+#define V3_LB_BASE_ADR_SIZE_8MB (3 << 4)
+#define V3_LB_BASE_ADR_SIZE_16MB (4 << 4)
+#define V3_LB_BASE_ADR_SIZE_32MB (5 << 4)
+#define V3_LB_BASE_ADR_SIZE_64MB (6 << 4)
+#define V3_LB_BASE_ADR_SIZE_128MB (7 << 4)
+#define V3_LB_BASE_ADR_SIZE_256MB (8 << 4)
+#define V3_LB_BASE_ADR_SIZE_512MB (9 << 4)
+#define V3_LB_BASE_ADR_SIZE_1GB (10 << 4)
+#define V3_LB_BASE_ADR_SIZE_2GB (11 << 4)
+
+#define v3_addr_to_lb_base(a) ((a) & V3_LB_BASE_ADR_BASE)
+
+/* LB_MAP0,1 bits (Local bus -> PCI) */
+#define V3_LB_MAP_MAP_ADR 0xfff0U
+#define V3_LB_MAP_TYPE (7 << 1)
+#define V3_LB_MAP_AD_LOW_EN BIT(0)
+
+#define V3_LB_MAP_TYPE_IACK (0 << 1)
+#define V3_LB_MAP_TYPE_IO (1 << 1)
+#define V3_LB_MAP_TYPE_MEM (3 << 1)
+#define V3_LB_MAP_TYPE_CONFIG (5 << 1)
+#define V3_LB_MAP_TYPE_MEM_MULTIPLE (6 << 1)
+
+#define v3_addr_to_lb_map(a) (((a) >> 16) & V3_LB_MAP_MAP_ADR)
+
+/* LB_BASE2 bits (Local bus -> PCI IO) */
+#define V3_LB_BASE2_ADR_BASE 0xff00U
+#define V3_LB_BASE2_SWAP (3 << 6)
+#define V3_LB_BASE2_ENABLE BIT(0)
+
+#define v3_addr_to_lb_base2(a) (((a) >> 16) & V3_LB_BASE2_ADR_BASE)
+
+/* LB_MAP2 bits (Local bus -> PCI IO) */
+#define V3_LB_MAP2_MAP_ADR 0xff00U
+
+#define v3_addr_to_lb_map2(a) (((a) >> 16) & V3_LB_MAP2_MAP_ADR)
+
+/* ARM Integrator-specific extended control registers */
+#define INTEGRATOR_SC_PCIENABLE_OFFSET 0x18
+#define INTEGRATOR_SC_LBFADDR_OFFSET 0x20
+#define INTEGRATOR_SC_LBFCODE_OFFSET 0x24
+
+struct v3_pci {
+ struct device *dev;
+ void __iomem *base;
+ void __iomem *config_base;
+ struct pci_bus *bus;
+ u32 config_mem;
+ u32 io_mem;
+ u32 non_pre_mem;
+ u32 pre_mem;
+ phys_addr_t io_bus_addr;
+ phys_addr_t non_pre_bus_addr;
+ phys_addr_t pre_bus_addr;
+ struct regmap *map;
+};
+
+static void __iomem *v3_map_bus(struct pci_bus *bus,
+ unsigned int devfn, int offset)
+{
+ struct v3_pci *v3 = bus->sysdata;
+ unsigned int address, mapaddress, busnr;
+
+ busnr = bus->number;
+ if (busnr == 0) {
+ int slot = PCI_SLOT(devfn);
+
+ /*
+ * local bus segment so need a type 0 config cycle
+ *
+ * build the PCI configuration "address" with one-hot in
+ * A31-A11
+ *
+ * mapaddress:
+ * 3:1 = config cycle (101)
+ * 0 = PCI A1 & A0 are 0 (0)
+ */
+ address = PCI_FUNC(devfn) << 8;
+ mapaddress = V3_LB_MAP_TYPE_CONFIG;
+
+ if (slot > 12)
+ /*
+ * high order bits are handled by the MAP register
+ */
+ mapaddress |= BIT(slot - 5);
+ else
+ /*
+ * low order bits handled directly in the address
+ */
+ address |= BIT(slot + 11);
+ } else {
+ /*
+ * not the local bus segment so need a type 1 config cycle
+ *
+ * address:
+ * 23:16 = bus number
+ * 15:11 = slot number (7:3 of devfn)
+ * 10:8 = func number (2:0 of devfn)
+ *
+ * mapaddress:
+ * 3:1 = config cycle (101)
+ * 0 = PCI A1 & A0 from host bus (1)
+ */
+ mapaddress = V3_LB_MAP_TYPE_CONFIG | V3_LB_MAP_AD_LOW_EN;
+ address = (busnr << 16) | (devfn << 8);
+ }
+
+ /*
+ * Set up base0 to see all 512Mbytes of memory space (not
+ * prefetchable), this frees up base1 for re-use by
+ * configuration memory
+ */
+ writel(v3_addr_to_lb_base(v3->non_pre_mem) |
+ V3_LB_BASE_ADR_SIZE_512MB | V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE0);
+
+ /*
+ * Set up base1/map1 to point into configuration space.
+ */
+ writel(v3_addr_to_lb_base(v3->config_mem) |
+ V3_LB_BASE_ADR_SIZE_16MB | V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE1);
+ writew(mapaddress, v3->base + V3_LB_MAP1);
+
+ return v3->config_base + address + offset;
+}
+
+static void v3_unmap_bus(struct v3_pci *v3)
+{
+ /*
+ * Reassign base1 for use by prefetchable PCI memory
+ */
+ writel(v3_addr_to_lb_base(v3->pre_mem) |
+ V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH |
+ V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE1);
+ writew(v3_addr_to_lb_map(v3->pre_bus_addr) |
+ V3_LB_MAP_TYPE_MEM_MULTIPLE,
+ v3->base + V3_LB_MAP1);
+
+ /*
+ * And shrink base0 back to a 256M window (NOTE: MAP0 already correct)
+ */
+ writel(v3_addr_to_lb_base(v3->non_pre_mem) |
+ V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE0);
+}
+
+
+static int v3_pci_read_config(struct pci_bus *bus, unsigned int fn,
+ int config, int size, u32 *value)
+{
+ struct v3_pci *v3 = bus->sysdata;
+ int ret;
+
+ dev_dbg(&bus->dev,
+ "[read] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n",
+ PCI_SLOT(fn), PCI_FUNC(fn), config, size, *value);
+ ret = pci_generic_config_read(bus, fn, config, size, value);
+ v3_unmap_bus(v3);
+ return ret;
+}
+
+static int v3_pci_write_config(struct pci_bus *bus, unsigned int fn,
+ int config, int size, u32 value)
+{
+ struct v3_pci *v3 = bus->sysdata;
+ int ret;
+
+ dev_dbg(&bus->dev,
+ "[write] slt: %.2d, fnc: %d, cnf: 0x%.2X, val (%d bytes): 0x%.8X\n",
+ PCI_SLOT(fn), PCI_FUNC(fn), config, size, value);
+ ret = pci_generic_config_write(bus, fn, config, size, value);
+ v3_unmap_bus(v3);
+ return ret;
+}
+
+static struct pci_ops v3_pci_ops = {
+ .map_bus = v3_map_bus,
+ .read = v3_pci_read_config,
+ .write = v3_pci_write_config,
+};
+
+static irqreturn_t v3_irq(int irq, void *data)
+{
+ struct v3_pci *v3 = data;
+ u32 status;
+
+ status = readw(v3->base + V3_PCI_STAT);
+ if (status & V3_PCI_STAT_PAR_ERR)
+ dev_err(v3->dev, "parity error interrupt\n");
+ if (status & V3_PCI_STAT_SYS_ERR)
+ dev_err(v3->dev, "system error interrupt\n");
+ if (status & V3_PCI_STAT_M_ABORT_ERR)
+ dev_err(v3->dev, "master abort error interrupt\n");
+ if (status & V3_PCI_STAT_T_ABORT_ERR)
+ dev_err(v3->dev, "target abort error interrupt\n");
+ writew(status, v3->base + V3_PCI_STAT);
+
+ status = readb(v3->base + V3_LB_ISTAT);
+ if (status & V3_LB_ISTAT_MAILBOX)
+ dev_info(v3->dev, "PCI mailbox interrupt\n");
+ if (status & V3_LB_ISTAT_PCI_RD)
+ dev_err(v3->dev, "PCI target LB->PCI READ abort interrupt\n");
+ if (status & V3_LB_ISTAT_PCI_WR)
+ dev_err(v3->dev, "PCI target LB->PCI WRITE abort interrupt\n");
+ if (status & V3_LB_ISTAT_PCI_INT)
+ dev_info(v3->dev, "PCI pin interrupt\n");
+ if (status & V3_LB_ISTAT_PCI_PERR)
+ dev_err(v3->dev, "PCI parity error interrupt\n");
+ if (status & V3_LB_ISTAT_I2O_QWR)
+ dev_info(v3->dev, "I2O inbound post queue interrupt\n");
+ if (status & V3_LB_ISTAT_DMA1)
+ dev_info(v3->dev, "DMA channel 1 interrupt\n");
+ if (status & V3_LB_ISTAT_DMA0)
+ dev_info(v3->dev, "DMA channel 0 interrupt\n");
+ /* Clear all possible interrupts on the local bus */
+ writeb(0, v3->base + V3_LB_ISTAT);
+ if (v3->map)
+ regmap_write(v3->map, INTEGRATOR_SC_PCIENABLE_OFFSET, 3);
+
+ return IRQ_HANDLED;
+}
+
+static int v3_integrator_init(struct v3_pci *v3)
+{
+ v3->map = syscon_regmap_lookup_by_compatible("arm,integrator-ap-syscon");
+ if (IS_ERR(v3->map)) {
+ dev_err(v3->dev, "no syscon\n");
+ return -ENODEV;
+ }
+ regmap_write(v3->map, INTEGRATOR_SC_PCIENABLE_OFFSET, 3);
+ dev_info(v3->dev, "initialized PCI V3 Integrator/AP integration\n");
+
+ return 0;
+}
+
+static int v3_pci_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct resource *regs;
+ resource_size_t io_base;
+ struct resource_entry *win;
+ struct v3_pci *v3;
+ struct resource *config;
+ struct resource *mem;
+ struct resource *io;
+ struct pci_host_bridge *host;
+ struct clk *clk;
+ unsigned int pci_cmd;
+ u16 temp;
+ int irq;
+ int ret;
+ LIST_HEAD(res);
+
+ host = pci_alloc_host_bridge(sizeof(*v3));
+ if (!host)
+ return -ENOMEM;
+
+ host->dev.parent = dev;
+ host->ops = &v3_pci_ops;
+ host->busnr = 0;
+ host->msi = NULL;
+ v3 = pci_host_bridge_priv(host);
+ host->sysdata = v3;
+ v3->dev = dev;
+
+ /* Get and enable host clock */
+ clk = devm_clk_get(&pdev->dev, NULL);
+ if (IS_ERR(clk)) {
+ dev_err(&pdev->dev, "clock not found\n");
+ return PTR_ERR(clk);
+ }
+ ret = clk_prepare_enable(clk);
+ if (ret) {
+ dev_err(&pdev->dev, "unable to enable clock\n");
+ return ret;
+ }
+
+ regs = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ v3->base = devm_ioremap_resource(dev, regs);
+ if (IS_ERR(v3->base))
+ return PTR_ERR(v3->base);
+
+ ret = of_pci_get_host_bridge_resources(np, 0, 0xff, &res, &io_base);
+ if (ret)
+ return ret;
+
+ ret = devm_request_pci_bus_resources(dev, &res);
+ if (ret)
+ return ret;
+
+ /* Get and request error IRQ resource */
+ irq = platform_get_irq(pdev, 0);
+ if (irq <= 0) {
+ dev_err(&pdev->dev, "unable to obtain PCIv3 error IRQ\n");
+ return -ENODEV;
+ }
+ ret = devm_request_irq(&pdev->dev, irq, v3_irq, 0,
+ "PCIv3 error", v3);
+ if (ret < 0) {
+ dev_err(&pdev->dev, "unable to request PCIv3 error IRQ %d (%d)\n", irq, ret);
+ return ret;
+ }
+
+ /*
+ * Unlock V3 registers, but only if they were previously locked.
+ */
+ if (readw(v3->base + V3_SYSTEM) & V3_SYSTEM_M_LOCK)
+ writew(0xa05f, v3->base + V3_SYSTEM);
+
+ /* Get the I/O and memory ranges from DT */
+ resource_list_for_each_entry(win, &res) {
+ switch (resource_type(win->res)) {
+ case 0:
+ /* The device trees use resource 0x0 for the config space range */
+ config = win->res;
+ config->name = "V3 Config Space";
+ v3->config_mem = config->start;
+ dev_info(dev, "CONFIG SPACE window start %08x, size %08x (offset = %08x, bus addr = %08x)\n",
+ v3->config_mem, resource_size(config), win->offset,
+ config->start - win->offset);
+ if (!devm_request_mem_region(dev, config->start, resource_size(config),
+ "V3 Config Space"))
+ dev_err(dev, "can't request config region\n");
+ v3->config_base = devm_ioremap(dev, config->start,
+ resource_size(config));
+ if (!v3->config_base)
+ dev_err(dev, "failed to remap config space\n");
+ break;
+ case IORESOURCE_IO:
+ io = win->res;
+ io->name = "V3 PCI I/O";
+ v3->io_mem = io->start;
+ v3->io_bus_addr = io->start - win->offset;
+ dev_info(dev, "I/O window start %08x, bus addr %08x, size %08x\n",
+ v3->io_mem, v3->io_bus_addr, resource_size(io));
+ ret = pci_remap_iospace(io, io_base);
+ if (ret) {
+ dev_warn(dev, "error %d: failed to map resource %pR\n",
+ ret, io);
+ continue;
+ }
+ /*
+ * Setup window 2 - PCI IO
+ */
+ writel(v3_addr_to_lb_base2(v3->io_mem) | V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE2);
+ writew(v3_addr_to_lb_map2(v3->io_bus_addr), v3->base + V3_LB_MAP2);
+ break;
+ case IORESOURCE_MEM:
+ mem = win->res;
+ if (mem->flags & IORESOURCE_PREFETCH) {
+ mem->name = "V3 PCI PRE-MEM";
+ v3->pre_mem = mem->start;
+ v3->pre_bus_addr = mem->start - win->offset;
+ dev_info(dev, "PREFETCHABLE MEM window start %08x, bus addr %08x, size %08x\n",
+ v3->pre_mem, v3->pre_bus_addr, resource_size(mem));
+ /*
+ * Setup window 1 - PCI prefetchable memory
+ * Local: 0x50000000 Bus: 0x10000000 Size: 256MB
+ * FIXME: get size from resource_size()
+ */
+ writel(v3_addr_to_lb_base(v3->pre_mem) |
+ V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_PREFETCH |
+ V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE1);
+ writew(v3_addr_to_lb_map(v3->pre_bus_addr) |
+ V3_LB_MAP_TYPE_MEM_MULTIPLE,
+ v3->base + V3_LB_MAP1);
+ } else {
+ mem->name = "V3 PCI NON-PRE-MEM";
+ v3->non_pre_mem = mem->start;
+ v3->non_pre_bus_addr = mem->start - win->offset;
+ dev_info(dev, "NON-PREFETCHABLE MEM window start %08x, bus addr %08x, size %08x\n",
+ v3->non_pre_mem, v3->non_pre_bus_addr, resource_size(mem));
+ /*
+ * Setup window 0 - PCI non-prefetchable memory
+ * Local: 0x40000000 Bus: 0x00000000 Size: 256MB
+ * FIXME: get size from resource_size()
+ */
+ writel(v3_addr_to_lb_base(v3->non_pre_mem) |
+ V3_LB_BASE_ADR_SIZE_256MB | V3_LB_BASE_ENABLE,
+ v3->base + V3_LB_BASE0);
+ writew(v3_addr_to_lb_map(v3->non_pre_bus_addr) |
+ V3_LB_MAP_TYPE_MEM,
+ v3->base + V3_LB_MAP0);
+
+ }
+ break;
+ case IORESOURCE_BUS:
+ dev_info(dev, "BUS %d\n", win->res->start);
+ break;
+ default:
+ break;
+ }
+ }
+
+ /*
+ * Disable PCI to host IO cycles
+ */
+ temp = readw(v3->base + V3_PCI_CFG) & ~V3_PCI_CFG_M_I2O_EN;
+ temp |= V3_PCI_CFG_M_IO_REG_DIS | V3_PCI_CFG_M_IO_DIS;
+ writew(temp, v3->base + V3_PCI_CFG);
+
+ dev_info(dev, "FIFO_CFG: %04x FIFO_PRIO: %04x\n",
+ readw(v3->base + V3_FIFO_CFG), readw(v3->base + V3_FIFO_PRIORITY));
+
+ /*
+ * Set the V3 FIFO such that writes have higher priority than
+ * reads, and local bus write causes local bus read fifo flush.
+ * Same for PCI.
+ */
+ writew(0x0a0a, v3->base + V3_FIFO_PRIORITY);
+
+ /*
+ * Re-lock the system register.
+ */
+ temp = readw(v3->base + V3_SYSTEM) | V3_SYSTEM_M_LOCK;
+ writew(temp, v3->base + V3_SYSTEM);
+
+ /*
+ * Clear any error conditions, and enable write errors.
+ */
+ writeb(0, v3->base + V3_LB_ISTAT);
+ writew(readw(v3->base + V3_LB_CFG) | BIT(10), v3->base + V3_LB_CFG);
+ writeb(0x28, v3->base + V3_LB_IMASK);
+
+ /* Special Integrator initialization */
+ if (of_device_is_compatible(np, "arm,integrator-ap-pci")) {
+ ret = v3_integrator_init(v3);
+ if (ret)
+ return ret;
+ }
+
+ /* Post-init */
+ pci_cmd = PCI_COMMAND_MEMORY | PCI_COMMAND_MASTER | PCI_COMMAND_INVALIDATE;
+ writew(pci_cmd, v3->base + V3_PCI_CMD);
+ writeb(0, v3->base + V3_LB_ISTAT); /* Was 0x40 */
+ writeb(V3_LB_ISTAT_PCI_RD | V3_LB_ISTAT_PCI_WR | V3_LB_ISTAT_PCI_PERR,
+ v3->base + V3_LB_IMASK);
+
+ list_splice_init(&res, &host->windows);
+ ret = pci_scan_root_bus_bridge(host);
+ if (ret) {
+ dev_err(dev, "failed to register host: %d\n", ret);
+ return ret;
+ }
+ v3->bus = host->bus;
+
+ pci_bus_assign_resources(v3->bus);
+ pci_bus_add_devices(v3->bus);
+ pci_free_resource_list(&res);
+
+ return 0;
+}
+
+static const struct of_device_id v3_pci_of_match[] = {
+ {
+ .compatible = "v3,v360epc-pci",
+ },
+ {},
+};
+
+static struct platform_driver v3_pci_driver = {
+ .driver = {
+ .name = "pci-v3-semi",
+ .of_match_table = of_match_ptr(v3_pci_of_match),
+ },
+ .probe = v3_pci_probe,
+};
+builtin_platform_driver(v3_pci_driver);
--
2.9.4
