On Fri, Apr 29, 2016 at 11:05:34PM +0530, Jayachandran C wrote:
> On Fri, Apr 29, 2016 at 2:07 PM, Lorenzo Pieralisi
> <lorenzo.pieralisi@xxxxxxx> wrote:
> > On Thu, Apr 28, 2016 at 04:48:00PM -0500, Bjorn Helgaas wrote:
> >
> > [...]
> >
> >> > +static int pci_acpi_setup_ecam_mapping(struct acpi_pci_root *root,
> >> > + struct acpi_pci_generic_root_info *ri)
> >> > +{
> >> > + u16 seg = root->segment;
> >> > + u8 bus_start = root->secondary.start;
> >> > + u8 bus_end = root->secondary.end;
> >> > + struct pci_config_window *cfg;
> >> > + struct mcfg_entry *e;
> >> > + phys_addr_t addr;
> >> > + int err = 0;
> >> > +
> >> > + mutex_lock(&pci_mcfg_lock);
> >>
> >> What does this lock protect? The pci_mcfg_list should already be
> >> initialized by the time we get there, and it should be immutable for
> >> the life of the system. In fact, I would prefer if we could just
> >> search the static table itself whenever we need it rather than caching
> >> it in our own list. But I don't think we can easily do that because
> >> acpi_table_parse() is __init.
> >>
> >> > + e = pci_mcfg_lookup(seg, bus_start);
> >>
> >> I would argue that we should check for _CBA first, and fall back to
> >> MCFG if _CBA doesn't exist.
> >>
> >> > + if (!e) {
> >> > + addr = acpi_pci_root_get_mcfg_addr(root->device->handle);
> >>
> >> IMO, acpi_pci_root_get_mcfg_addr() is misnamed. It should be
> >> acpi_pci_config_base_addr() or similar. It definitely is not related
> >> to MCFG. Not your fault, obviously.
> >>
> >> > + if (addr == 0) {
> >> > + pr_err(PREFIX"%04x:%02x-%02x bus range error\n",
> >> > + seg, bus_start, bus_end);
> >> > + err = -ENOENT;
> >> > + goto err_out;
> >> > + }
> >> > + } else {
> >> > + if (bus_start != e->bus_start) {
> >> > + pr_err("%04x:%02x-%02x bus range mismatch %02x\n",
> >> > + seg, bus_start, bus_end, e->bus_start);
> >> > + err = -EINVAL;
> >> > + goto err_out;
> >> > + } else if (bus_end != e->bus_end) {
> >> > + pr_warn("%04x:%02x-%02x bus end mismatch %02x\n",
> >> > + seg, bus_start, bus_end, e->bus_end);
> >> > + bus_end = min(bus_end, e->bus_end);
> >> > + }
> >> > + addr = e->addr;
> >> > + }
> >>
> >> I really don't think you need a lock around this, so you can factor
> >> out the address lookup into something like:
> >>
> >> addr = acpi_pci_config_base_addr(...);
> >> if (addr)
> >> return addr;
> >>
> >> return acpi_pci_mcfg_lookup(seg, busn_res);
> >>
> >> You can check inside acpi_pci_mcfg_lookup() to make sure the entry you
> >> find covers the entire [busn_res.start-busn_res.end] range and return
> >> failure if it doesn't. At this point, I'm not sure it's worth it to
> >> truncate the host bridge bus range to match something we find in MCFG.
> >>
> >> If the MCFG entry covers *more* than the host bridge range from _CRS,
> >> that's fine. In any case, we have to be careful with the start address,
> >> because the MCFG start address is always based on bus 0, but I think
> >> pci_generic_ecam_create() expects the start address based on the
> >> bus_start you pass to it.
> >
> > Yes, I spotted this too, it is unfortunate but DT and MCFG handle
> > the ECAM regions differently. In DT the reg property is relative
> > to bus_start - ie reg MMIO region maps config space starting at
> > the first bus in bus-range:
> >
> > Documentation/devicetree/bindings/pci/host-generic-pci.txt
> >
> > in ACPI(MCFG) as you said it is always relative to bus 0, it is
> > unfortunate but the address to be mapped should be computed
> > differently in the ECAM layer.
>
> Can't this be handled by fixing up the address before passing to
> pci_generic_ecam_create?
Yes it can, you just need to apply the bus shift, given that we know
it is ECAM anyway you can even add a macro in the ecam generic header to
compute it, anyway that's a minor detail, we just should not forget to
fix it.
Lorenzo
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
