On Friday 16 May 2014 18:44:44 Murali Karicheri wrote:
> On 5/15/2014 12:28 PM, Arnd Bergmann wrote:
> > On Thursday 15 May 2014 12:01:32 Murali Karicheri wrote:
> >> +Sample bindings shown below:-
> >> +
> >> + - Remove ti,enable-linktrain if boot loader already does Link training and do EP
> >> + configuration.
> >> + - Remove ti,init-phy if boot loader already initialize the phy and sets up pcie
> >> + link
> > You actually have to document all the properties. Have a look at the
> > other bindings for what this means.
>
> Actually this is dw pcie variant. So I will document if there are any
> deviations from the dw-designware
> bindings. Based on comments from Jingo, I think I need to add a new DT
> property for old hw that we
> use in keystone. May be a compatibility string for older dw h/w like
> "snps ,dw-pcie-v3.65" is that we
> could use and do things differently in the common code.
A compatible string with the exact version sounds like a good idea, yes.
> So I will update the Documentation of dw bindings once we agree on this.
> >> +
> >> + pcie@21800000 {
> >> + compatible = "ti,keystone-pcie";
> >> + device_type = "pci";
> >> + clocks = <&clkpcie>;
> >> + clock-names = "pcie";
> > The dw-pcie binding lists two clocks.
>
> Ok. As per dw documentation, pcie and pcie_bus are the clocks. But
> pci-imx6 is currently not using pcie_bus. So the pcie_bus
> clock is actually optional. In the case of keystone pcie, bus clock is
> provided by the phy hardware and if I need to provide
> a clock for bus, it has to be a dummy or change documentation to make
> pcie_bus an optional clock. I prefer later, but want
> to know if this is true for pci-imx6. There is also a plan to move the
> pcie clock API call to designware core. So making pcie_bus
> clock optional looks correct to me.
A documentation change sounds fine to me. How about documenting that
there should be either a "pcie_bus" clock or a phy reference?
> >> + #address-cells = >;
> >> + #size-cells = <2>;
> >> + reg = <0x21800000 0x1000>, <0x0262014c 4>;
> >> + reg-names = "reg_rc_app", "reg_devcfg";
> > There should be standard names that are documented in the binding.
>
> Currently Documentation says
>
> - reg: base addresses and lengths of the pcie controller,
> the phy controller, additional register for the phy controller.
>
> And following dw drivers defines as
>
> samsung,exynos5440-pcie
>
> reg = <0x290000 0x1000
> 0x270000 0x1000
> 0x271000 0x40>;
>
> fsl,imx6q-pcie"
> reg = <0x01ffc000 0x4000>; /* DBI */
>
> There are no names used for registers. So this needs to be documented in
> the dw-designware
> bindings. reg_dbi is what is common to pci controller assuming at index
> 0 of the both above drivers use
> reg_dbi address for config space. Shall I modify the documentation to
> include optional reg name
> reg_dbi for config space base address registers? Additional registers
> are optional and varies from
> platform to platform. Phy registers are actually part of Phy driver and
> should be removed from
> the dw-documentation bindings. Agree?
It makes sense to remove the phy registers if there is always a separate
phy driver. Regarding the names, it's probably easier to remove them
completely than to document them.
If the register names are optional, you can't rely on them anyway
and have to uses the indexes/
> >
> >> + interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
> >> + <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>; /* Error IRQ */
> > What are all these interrupts?
> These are MSI interrupts tied to the GIC over which MSI interrupts are
> multiplexed. I will document
> it in the keystone PCI DT bindings.
Maybe they should be moved into the subnode that has the LSI interrupts,
or perhaps a separate node? I don't know how the other dw-pcie variants
do it, but it always seems like a good idea to keep MSI separate because
you might not want to use it if there is also an MSI capable GIC in the
system.
> >> + ranges = <0x00000800 0 0x21801000 0x21801000 0 0x0002000 /* Configuration space */
> >> + 0x81000000 0 0 0x24000000 0 0x4000 /* downstream I/O */
> >> + 0x82000000 0 0x50000000 0x50000000 0 0x10000000>; /* non-prefetchable memory */
> > Please move the config space into 'reg' now instead of 'ranges'.
> > This was a mistake earlier, and there are already other front-ends
> > doing the same thing.
> This has to be coordinated with other drivers when DW core makes the
> change.
>
> Jingoo, Sean,
>
> What is the plan for this change? I have to defer this currently.
> >> + #interrupt-cells = <1>;
> >> + interrupt-map-mask = <0 0 0 0>;
> >> + interrupt-map = <0 0 0 1 &pcie_intc 1>, // INT A
> >> + <0 0 0 2 &pcie_intc 2>, // INT B
> >> + <0 0 0 3 &pcie_intc 3>, // INT C
> >> + <0 0 0 4 &pcie_intc 4>; // INT D
> > I think this is the wrong map-mask.
> I think this should be changed to
>
> interrupt-map-mask = <0 0 0 0x7> ?
That sounds reasonable. Is that what your hardware implements?
Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
