On 5/15/2014 12:28 PM, Arnd Bergmann wrote:
On Thursday 15 May 2014 12:01:32 Murali Karicheri wrote:
+Sample bindings shown below:-
+
+ - Remove ti,enable-linktrain if boot loader already does Link training and do EP
+ configuration.
+ - Remove ti,init-phy if boot loader already initialize the phy and sets up pcie
+ link
You actually have to document all the properties. Have a look at the
other bindings for what this means.
Actually this is dw pcie variant. So I will document if there are any
deviations from the dw-designware
bindings. Based on comments from Jingo, I think I need to add a new DT
property for old hw that we
use in keystone. May be a compatibility string for older dw h/w like
"snps ,dw-pcie-v3.65" is that we
could use and do things differently in the common code.
So I will update the Documentation of dw bindings once we agree on this.
+
+ pcie@21800000 {
+ compatible = "ti,keystone-pcie";
+ device_type = "pci";
+ clocks = <&clkpcie>;
+ clock-names = "pcie";
The dw-pcie binding lists two clocks.
Ok. As per dw documentation, pcie and pcie_bus are the clocks. But
pci-imx6 is currently not using pcie_bus. So the pcie_bus
clock is actually optional. In the case of keystone pcie, bus clock is
provided by the phy hardware and if I need to provide
a clock for bus, it has to be a dummy or change documentation to make
pcie_bus an optional clock. I prefer later, but want
to know if this is true for pci-imx6. There is also a plan to move the
pcie clock API call to designware core. So making pcie_bus
clock optional looks correct to me.
Seen/Jingoo, any comments?
+ #address-cells = >;
+ #size-cells = <2>;
+ reg = <0x21800000 0x1000>, <0x0262014c 4>;
+ reg-names = "reg_rc_app", "reg_devcfg";
There should be standard names that are documented in the binding.
Currently Documentation says
- reg: base addresses and lengths of the pcie controller,
the phy controller, additional register for the phy controller.
And following dw drivers defines as
samsung,exynos5440-pcie
reg = <0x290000 0x1000
0x270000 0x1000
0x271000 0x40>;
fsl,imx6q-pcie"
reg = <0x01ffc000 0x4000>; /* DBI */
There are no names used for registers. So this needs to be documented in
the dw-designware
bindings. reg_dbi is what is common to pci controller assuming at index
0 of the both above drivers use
reg_dbi address for config space. Shall I modify the documentation to
include optional reg name
reg_dbi for config space base address registers? Additional registers
are optional and varies from
platform to platform. Phy registers are actually part of Phy driver and
should be removed from
the dw-documentation bindings. Agree?
+ interrupts = <GIC_SPI 30 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 31 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 32 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 33 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 34 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 35 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 36 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 37 IRQ_TYPE_EDGE_RISING>,
+ <GIC_SPI 38 IRQ_TYPE_EDGE_RISING>; /* Error IRQ */
What are all these interrupts?
These are MSI interrupts tied to the GIC over which MSI interrupts are
multiplexed. I will document
it in the keystone PCI DT bindings.
+ ranges = <0x00000800 0 0x21801000 0x21801000 0 0x0002000 /* Configuration space */
+ 0x81000000 0 0 0x24000000 0 0x4000 /* downstream I/O */
+ 0x82000000 0 0x50000000 0x50000000 0 0x10000000>; /* non-prefetchable memory */
Please move the config space into 'reg' now instead of 'ranges'.
This was a mistake earlier, and there are already other front-ends
doing the same thing.
This has to be coordinated with other drivers when DW core makes the
change.
Jingoo, Sean,
What is the plan for this change? I have to defer this currently.
+ num-lanes = <2>;
+ ti,enable-linktrain;
+ ti,init-phy;
+
+ /* PCIE phy */
+ phys = <&pcie0_phy>;
+ phy-names = "pcie-phy";
+
+ #interrupt-cells = <1>;
+ interrupt-map-mask = <0 0 0 0>;
+ interrupt-map = <0 0 0 1 &pcie_intc 1>, // INT A
+ <0 0 0 2 &pcie_intc 2>, // INT B
+ <0 0 0 3 &pcie_intc 3>, // INT C
+ <0 0 0 4 &pcie_intc 4>; // INT D
I think this is the wrong map-mask.
I think this should be changed to
interrupt-map-mask = <0 0 0 0x7> ?
Arnd
--
To unsubscribe from this list: send the line "unsubscribe linux-pci" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
