Hi Ben, On: 24/03/2014 12:25, Phil wrote: > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > Hi Ben, > > On: 24/03/2014 12:16, Ben wrote: > > Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree bindings > > > > On 24/03/14 12:04, Phil.Edworthy@xxxxxxxxxxx wrote: > > > Hi Lucas, > > > > > > On: 21/03/2014 15:02, Phil wrote: > > >> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > > bindings > > >> > > >> Hi Lucas, > > >> > > >> On: 21/03/2014 14:31, Lucas wrote: > > >>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device tree > > > bindings > > >>> > > >>> Am Freitag, den 21.03.2014, 14:18 +0000 schrieb > > >>> Phil.Edworthy@xxxxxxxxxxx: > > >>>> Hi Lucas, > > >>>> > > >>>> On 21/03/2014 11:24, Lucas wrote: > > >>>>> Subject: Re: [PATCH v4 5/9] dt-bindings: pci: rcar pcie device > > > tree > > >>>> bindings > > >>>>> > > >>>>> Am Freitag, den 21.03.2014, 10:32 +0000 schrieb Phil Edworthy: > > >>>>>> This patch adds the bindings for the rcar PCIE driver. The > > > driver > > >>>>>> resides under drivers/pci/host/pcie-rcar.c > > >>>>>> > > >>>>>> Signed-off-by: Phil Edworthy <phil.edworthy@xxxxxxxxxxx> > > >>>>> > > >>>>> I have one question below. If you can answer this with yes after > > >>>>> thinking again about it, this is: > > >>>>> > > >>>>> Reviewed-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx> > > >>>>>> --- > > >>>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt | 40 > > >>>> ++++++++++++++++++++++ > > >>>>>> 1 file changed, 40 insertions(+) > > >>>>>> create mode 100644 > > > Documentation/devicetree/bindings/pci/rcar-pci.txt > > >>>>>> > > >>>>>> diff --git a/Documentation/devicetree/bindings/pci/rcar-pci.txt > > > b/ > > >>>>> Documentation/devicetree/bindings/pci/rcar-pci.txt > > >>>>>> new file mode 100644 > > >>>>>> index 0000000..0e219b0 > > >>>>>> --- /dev/null > > >>>>>> +++ b/Documentation/devicetree/bindings/pci/rcar-pci.txt > > >>>>>> @@ -0,0 +1,40 @@ > > >>>>>> +* Renesas RCar PCIe interface > > >>>>>> + > > >>>>>> +Required properties: > > >>>>>> +- compatible: should contain one of the following > > >>>>>> + "renesas,r8a7779-pcie", "renesas,r8a7790-pcie", > > >>>> "renesas,r8a7791-pcie" > > >>>>>> +- reg: base addresses and lengths of the pcie controller. > > >>>>>> +- #address-cells: set to <3> > > >>>>>> +- #size-cells: set to <2> > > >>>>>> +- device_type: set to "pci" > > >>>>>> +- ranges: ranges for the PCI memory and I/O regions > > >>>>>> +- interrupts: interrupt values for MSI interrupt > > >>>>>> +- #interrupt-cells: set to <1> > > >>>>>> +- interrupt-map-mask and interrupt-map: standard PCI properties > > >>>>>> + to define the mapping of the PCIe interface to interrupt > > >>>>>> + numbers. > > >>>>>> +- clocks: from common clock binding: handle to pci clock. > > >>>>>> +- clock-names: from common clock binding: should be "pcie" > > >>>>> > > >>>>> You really only have one PCIe clock? So the controller is > > > generating the > > >>>>> PCIe bus clock from it's register clock? No need to enable any > > > other > > >>>>> clock for PCIe to work? > > >>>> Yes, just the one clock. The PCIe bus clock is an external clock > > > dedicated > > >>>> to PCIe and SATA, and we have no control over it. > > >>>> > > >>> Is this some kind of always-on clock? If not you probably want a > > >>> reference to it from the PCIe driver even if it's shared between SATA > > >>> and PCIe. After all you don't want to end up unconditionally enabling > > >>> this clock from the board or SoC level just to have PCIe working, > > > right? > > >> Ok, I see, I'll need a reference to a board clock, even if it's always > > > on for > > >> these boards. > > > One small question... > > > > > > The patches added the PCIe host controller to two devices, r8a7790 and > > > r8a7791. The r8a7790-based Lager board doesn't have the necessary hardware > > > to use PCIe, so should I add a dummy pcie_bus clock to the Lager board > > > dts, even though PCIe is not used? > > > > > > I'm just wondering what the dts file looks like for a board that doesn't > > > support many interfaces. Does it become littered with dummy clocks and > > > regulators? > > > > The bridge node should be set to disabled by default so it never gets > > probed. Any boards that want to use it can over-ride the status to be > > enabled. > Ok, thanks. Hmm, yes it doesn't get probed, but you still get a build problem as the DT entry references an clock that doesn't exist. Maybe I'm missing something... Phil -- To unsubscribe from this list: send the line "unsubscribe linux-pci" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
