On Tue, Nov 26, 2024 at 03:39:09PM +0800, Richard Zhu wrote:
> Before sending PME_TURN_OFF, don't test the LTSSM state. Since it's safe
> to send PME_TURN_OFF message regardless of whether the link is up or
> down. So, there would be no need to test the LTSSM state before sending
> PME_TURN_OFF message.
>
> Only print the message when ltssm_stat is not in DETECT and POLL.
> In the other words, there isn't an error message when no endpoint is
> connected at all.
>
> Signed-off-by: Richard Zhu <hongxing.zhu@xxxxxxx>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@xxxxxxxxxx>
- Mani
> ---
> v5 changes:
> - Remove the redundant check "(val > DW_PCIE_LTSSM_DETECT_WAIT)".
> v4 changes:
> - Keep error return when L2 entry is failed and the endpoint is
> connected refer to Krishna' comments. Thanks.
> v3 changes:
> - Refine the commit message refer to Manivannan's comments.
> - Regarding Frank's comments, avoid 10ms wait when no link up.
> v2 changes:
> - Don't remove L2 poll check.
> - Add one 1us delay after L2 entry.
> - No error return when L2 entry is timeout
> - Don't print message when no link up.
> ---
> .../pci/controller/dwc/pcie-designware-host.c | 38 +++++++++++--------
> drivers/pci/controller/dwc/pcie-designware.h | 1 +
> 2 files changed, 23 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index 24e89b66b772..bbd0ee862c12 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -927,25 +927,31 @@ int dw_pcie_suspend_noirq(struct dw_pcie *pci)
> if (dw_pcie_readw_dbi(pci, offset + PCI_EXP_LNKCTL) & PCI_EXP_LNKCTL_ASPM_L1)
> return 0;
>
> - /* Only send out PME_TURN_OFF when PCIE link is up */
> - if (dw_pcie_get_ltssm(pci) > DW_PCIE_LTSSM_DETECT_ACT) {
> - if (pci->pp.ops->pme_turn_off)
> - pci->pp.ops->pme_turn_off(&pci->pp);
> - else
> - ret = dw_pcie_pme_turn_off(pci);
> -
> - if (ret)
> - return ret;
> + if (pci->pp.ops->pme_turn_off)
> + pci->pp.ops->pme_turn_off(&pci->pp);
> + else
> + ret = dw_pcie_pme_turn_off(pci);
> + if (ret)
> + return ret;
>
> - ret = read_poll_timeout(dw_pcie_get_ltssm, val, val == DW_PCIE_LTSSM_L2_IDLE,
> - PCIE_PME_TO_L2_TIMEOUT_US/10,
> - PCIE_PME_TO_L2_TIMEOUT_US, false, pci);
> - if (ret) {
> - dev_err(pci->dev, "Timeout waiting for L2 entry! LTSSM: 0x%x\n", val);
> - return ret;
> - }
> + ret = read_poll_timeout(dw_pcie_get_ltssm, val,
> + val == DW_PCIE_LTSSM_L2_IDLE ||
> + val <= DW_PCIE_LTSSM_DETECT_WAIT,
> + PCIE_PME_TO_L2_TIMEOUT_US/10,
> + PCIE_PME_TO_L2_TIMEOUT_US, false, pci);
> + if (ret) {
> + /* Only dump message when ltssm_stat isn't in DETECT and POLL */
> + dev_err(pci->dev, "Timeout waiting for L2 entry! LTSSM: 0x%x\n", val);
> + return ret;
> }
>
> + /*
> + * Refer to r6.0, sec 5.3.3.2.1, software should wait at least
> + * 100ns after L2/L3 Ready before turning off refclock and
> + * main power. It's harmless too when no endpoint connected.
> + */
> + udelay(1);
> +
> dw_pcie_stop_link(pci);
> if (pci->pp.ops->deinit)
> pci->pp.ops->deinit(&pci->pp);
> diff --git a/drivers/pci/controller/dwc/pcie-designware.h b/drivers/pci/controller/dwc/pcie-designware.h
> index 347ab74ac35a..bf036e66717e 100644
> --- a/drivers/pci/controller/dwc/pcie-designware.h
> +++ b/drivers/pci/controller/dwc/pcie-designware.h
> @@ -330,6 +330,7 @@ enum dw_pcie_ltssm {
> /* Need to align with PCIE_PORT_DEBUG0 bits 0:5 */
> DW_PCIE_LTSSM_DETECT_QUIET = 0x0,
> DW_PCIE_LTSSM_DETECT_ACT = 0x1,
> + DW_PCIE_LTSSM_DETECT_WAIT = 0x6,
> DW_PCIE_LTSSM_L0 = 0x11,
> DW_PCIE_LTSSM_L2_IDLE = 0x15,
>
> --
> 2.37.1
>
--
மணிவண்ணன் சதாசிவம்
