On Mon, Aug 26, 2024 at 6:43 AM Stanimir Varbanov <svarbanov@xxxxxxx> wrote:
>
> Hi Jim,
>
> <cut>
>
> >
> > Hi Stan,
> >
> > Most of the clocks on the STB chips come up active so one does not
> > have to turn them on and off to have the device function. It helps
> > power savings to do this although I'm not sure it is significant.
> >>
> >>>
> >>> Perhaps you don't see the dependence on the PCIe clocks if the 2712
> >>> does not give the PCIe node a clock property and instead keeps its
> >>> clocks on all of the time. In that case I would think that your
> >>> solution would be fine.
> >>
> >> What you mean by my solution? The one where avoiding assert of
> >> bridge_reset at link [1] bellow?
> >
> > Yes.
> >>
> >> If so, I still cannot understand the relation between bridge_reset and
> >> rescal as the comment mentions:
> >>
> >> "Shutting down this bridge on pcie1 means accesses to rescal block will
> >> hang the chip if another RC wants to assert/deassert rescal".
> >
> > I was just describing my observations; this should not be happening.
> > I would say it is a HW bug for the 2712. I can file a bug against the
> > 2712 but that will not help us right now. From what I was told by HW,
> > asserting the PCIe1 bridge reset does not affect the rescal settings,
> > but it does freeze access to the rescal registers, and that is game
> > over for the other PCIe controllers accessing the rescal registers.
>
> Good findings, thank you.
>
> The problem comes from this snippet from brcm_pcie_probe() :
>
> ret = pci_host_probe(bridge);
> if (!ret && !brcm_pcie_link_up(pcie))
> ret = -ENODEV;
>
> if (ret) {
> brcm_pcie_remove(pdev);
> return ret;
> }
>
> Even when pci_host_probe() is successful the .probe will fail if there
> are no endpoint devices on this root port bus. This is the case when
> probing pcie1 port which is the one with external connector. Cause the
> probe is failing we call reset_control_rearm(rescal) from
> brcm_pcie_remove(), after that during .probe of pcie2 (the root port
> where RP1 south-bridge is attached) reset_control_reset(rescal) will
> issue rescal reset thus rescal-reset driver will stuck on read/write
> registers.
>
> I think we have to drop this link-up check and allow the probe to finish
> successfully. Even that there no PCI devices attached to bus we want the
> root port to be visible by lspci tool.
Hi Stan,
What is gained by having only the root bridge shown by lspci? We do
not support PCIe hotplug so why have lspci reporting a bridge with no
devices?
The reason we do this is to save power -- when we see no device we
turn off the clocks, put things in reset (e.g. bridge), and turn off
the regulators. We have SoCs with multiple controllers and they
cannot afford to be supplying power to controllers with non-populated
sockets; these may be products that are trying to conform to mandated
energy-mode specifications.
This will solve partially the
> issue with accessing rescal reset-controller registers after asserting
> bridge_reset. The other part of the problem will be solved by remove the
> invocation of reset_control_rearm(rescal) from __brcm_pcie_remove().
> That way only the first probed root port will issue rescal reset and
> every next probe will not try to reset rescal because we do not call
> _rearm(rescal).
In theory I agree with the above -- it should probably not be invoking
the rearm() when it is being deactivated. However, I am concerned
about a controller(s) going into s2 suspend/resume or unbind/bind.
Let me run some tests.
Regards,
Jim Quinlan
Broadcom STB/CM
>
> What do you think?
>
> ~Stan
Attachment:
smime.p7s
Description: S/MIME Cryptographic Signature
